Related Manuals for NEC NP50ZL
Summary of Contents for NEC NP50ZL
- Page 1 Lens Unit Handling Instructions Model NP50ZL レンズユニット 取扱説明書 NP50ZL 型名 镜头部件 操作说明书 NP50ZL 型号...
-
Page 2: Table Of Contents
CONTENTS Introduction ....................3 Cautions on handling the lens units ..........4 Disposing of your used product ............5 Included items ..................6 Things to prepare..................7 Preparation ....................7 How to install the support kit ............8 Adjusting position, size, and focus of the projection screen ..13 Lens shift ..................14 Zoom ....................15 Focus ....................15... -
Page 3: Introduction
Introduction This is the handling instructions for the NP50ZL zoom lens. This document describes cautions when handling the lens unit and how to install and adjust the support kit. CAUTION • After installing the lens unit, be sure to secure it to the projector using the support kit. Fail- ure to do so could cause the lens unit to fall, resulting in injury. -
Page 4: Cautions On Handling The Lens Units
Cautions on handling the lens units • The lens units are precision instruments. Do not subject them to shock or apply excessive force. • Do not move the projector with the lens unit mounted on it. Be sure to remove the lens unit beforehand. Subjecting the projector to shocks when moving could damage the lens unit or lens shift mechanism. • Before removing or mounting the lens unit, turn off the power, wait for the cooling fan to stop, then unplug the power cord from the power outlet. • During operation, DO NOT touch the lens surface, the focus/zoom motor or the gears. • Be very careful not to let dirt or oil get on the lens surface and not to scratch the lens surface. • To avoid the risk of the lens unit dropping, do not perform operations in high places. Perform operations on a flat surface. • When leaving the lens unit off for long periods of time, mount the dust-prevention cap on the projector to prevent dust or dirt from getting inside. レンズユニッ ト取り扱い上の注意 ・... -
Page 5: Disposing Of Your Used Product
Disposing of your used product In the European Union EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. When you dispose of such products, please follow the guid- ance of your local authority and/or ask the shop where you purchased the product. After collecting the used products, they are reused and recycled in a proper way. This effort will help us reduce the wastes as well as the negative impact to the human health and the environment at the minimum level. -
Page 6: Included Items
Included items Lens unit: 1 pc Support kit ⑦ Screw (M3 × 6) 4 pcs ② Lens holder 1 pc Parts C ⑫ Screw (M4 × 10) 4 pcs ③ Lens attachment 1 pc ⑧ Washer 4 pcs ④ Support base 1 pc ⑨... -
Page 7: Things To Prepare
Things to prepare • Phillips head screwdriver, ball end hexagon screwdriver (3 mm), wrench (7 mm) • For ceiling mount or portrait position, a mounting bracket with sufficient strength to support the combined weight of the projector, the lens unit, and the support kit Preparation Return the projector lens position to the home position without the lens mounted. For details on connecting the power cord and turning on/off, refer to the projector User’s Manual. Connect the power cord to the projector, and then press the (POWER) button to turn on the power. -
Page 8: How To Install The Support Kit
How to install the support kit ・ This section explains the installation method for model PA1004UL-W. The installation method is the same for other projectors. 1. Assemble the support base unit. Align the 6 screws holes on the support base with those on the lens holder and fasten using the 6 (M4 ×... - Page 9 3. Turn over the projector. Lay down the projector cabinet upside down on a table with soft cloth laid. CAUTION • For moving the projector, make sure you have at least two people. Attempting to move the projector alone could result in back pain or other injuries. 4. Attach the support unit to the projector. Place the support base unit assembled in step 1 on the projector as shown in the figure, align the 4 screws holes with those on the projector, and fasten using the 4 (M4 ×...
- Page 10 5. Return the projector to its original orientation. 6. According to the instructions on the projector manual, mount the lens unit onto the projector. ・ Make sure to remove the lens cap at the unit back side. If the lens unit with the lens cap re- maining on is installed on the projector, it may cause of malfunction. 5. プロジェクターを元の姿勢に戻す。 6.
- Page 11 Side view 横から見た図 侧视图 7. Fix the lens attachment to the lens holder. Pass 4 bolts (M4 × 30) with washer and nut through the holes on the face of the lens attachment to tighten them to the lens holder. When doing so, ensure that the washers are pressed lightly against the lens attachment and leave approximately 10 mm of space between the nut and the lens holder.
- Page 12 Screw holes A Screw holes B ネジ穴Ａ ネジ穴 B 螺钉孔 A 螺钉孔 B NOTE ・ The lens holder has 8 screw holes. Use screw holes A for PA1004UL-W/PA1004UL-B/PA804UL-W/PA804UL-B. This completes mounting the support kit. Set up the projector and connect the power cable and video cables. Then remove the front lens cap, turn on the projector, and adjust each setting. 参考 ・ レンズホルダーのネジ穴は 8 箇所あります。 NP-PA1004UL-WJL/NP-PA1004UL-BJL/NP-PA804UL-WJL/NP-PA804UL-BJL の...
-
Page 13: Adjusting Position, Size, And Focus Of The Projection Screen
Adjusting position, size, and focus of the projection screen • See the user manual of the projector for cautions and details on how to operate the projector. • When adjusting the projector, rotate the 4 bolts used in step 7 of the support kit installation. They are called the adjustment bolts. 投写画面の位置、大きさ、フォーカスの調整 ・ 注意事項と詳しい操作方法については、プロジェクターの取扱説明書をご覧ください。 ・ 調整の際は、サポートキット取り付け手順の 7 でしめ付けた 4 箇所のボルトを回します。こ れを調整ボルトと呼びます。 调整投影画面的位置、大小和焦点 • 相关注意事项以及操作投影机的具体细节请参阅投影机的用户手册。 • 在调整投影机时，请转动支撑套件安装步骤 7 中所使用的 4 颗螺栓。 它们称为调整螺栓。... -
Page 14: Lens Shift
• Lens shift Adjust the position of the projection screen. ① Press the SHIFT/HOME POSITION button. ② Press the ▼ ▲ ◀ ▶ buttons to move the projected image. NOTE ・ Loosen the 4 adjustment bolts and nuts when shifting the lens after tightening the adjustment bolts following a focus adjustment. •... -
Page 15: Zoom
• Zoom Adjusts the size of the projection screen. ① Press ZOOM/L-CALIB. button. ② Press ◀ ▶ buttons to adjust zoom. • Focus Focuses the projection screen. ① Press the FOCUS button. ② Press ◀ ▶ buttons to adjust focus of screen center. If the projection screen is not in focus, move between maximum and minimum focus to bring the focus as close to the screen as possible. •... - Page 16 ③ Tighten the top 2 adjustment bolts by a quarter turn each time. The adjustment bolts used for adjusting depend on where the projector is installed. • Tighten adjustment bolts 1 and 3 when installed on a table or floor and adjustment bolts 2 and 4 when installed on a ceiling.
- Page 17 Screen スクリーン 画面 Focus screen フォーカス面 聚焦画面 ⑤ Repeat steps ③ and ④ until the focus is not affected even when the adjustment bolts are tightened by more than a half turn. When the left and right sides of the screen’s focal point varies greatly as shown in the figure, tighten the adjustment bolts on the side far from the projector more. ⑥ Secure the adjustment bolts. Ensure that adjustment bolts not used in adjusting in step ③ are tight enough for the wash- ers to contact the lens attachment.
- Page 19 Turkish WEEE information relevant for Turkish market AEEE Yönetmeliğine Uygundur.
- Page 20 ○ ○ ○ 本表格依据 SJ/T 11364 的规定编制。 ○ ： 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以 下。 × ： 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量 要求。 备注 ： *1 ： 光学部件是指光学玻璃、显示设备、反射透镜等。 *2 ： 实装电气部件是指电路板、内置线缆、FAN、电源、传感器等。 © Sharp NEC Display Solutions, Ltd. 2021 *7N8R1171* Printed in China...