Sealey SHADE 10 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
 Ensure all workshop safety rules, regulations and conditions are complied with when using welding equipment. The head shield will
not off er protection against misuse of workshop tools, equipment, or accessories.
 This head shield is designed for eye and face protection during the following operations: manual metal arc welding, TIG welding,
pulsed arc welding and plasma cutting.
 WARNING! This head shield is not suitable for use with laser welding or oxygen acetylene welding or cutting.
 Prior to using the head shield for the fi rst time ensure that any protective fi lm is removed from the internal and external lenses.
 Maintain the head shield in good condition.
 Ensure that the clear lens is kept clean and is securely attached to the head shield.
Fit the head shield and adjust the head band so the head shield will sit as low and near to your face as possible.

 Use head shield only in temperatures ranging from -10°C to 60°C.
 Remove ill fi tting clothing, remove ties, watches, rings and other loose jewellery.
 Maintain correct balance and footing.
 Ensure the fl oor is clear from obstructions, not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the working area.
 Replace the lenses if they become scratched or covered in weld spatter.
 WARNING! The head shield will only protect the eyes/face from radiation and weld spatter.
 WARNING! The head shield will not protect against explosive devices or corrosive liquids.
 DO NOT use the head shield for any purpose for which it is not designed.
 DO NOT use the head shield unless you have been instructed in its use by a qualifi ed person.
 DO NOT get the head shield wet or use in damp or wet locations.
 DO NOT leave work place with head shield in lowered position.
DO NOT place the head shield on a hot surface.

 DO NOT use the head shield without the correct shade (fi lter) for the desired application.
 WARNING! During the welding process hazardous ultraviolet and infrared rays are emitted which can injure the eyes and cause
skin burns.
 It is advisable to wear suitable additional safety clothing to protect the rest of the body during the welding process.
 After use, clean head shield and store in a safe, dry, childproof location in it's original packaging.
 WARNING! DO NOT use the helmet if damaged or you suspect it may be faulty. (Contact Sealey stockist).
 WARNING! Welding vapours and gases can be harmful to your health. Keep your head away from any fumes, work in a well
ventilated area.
2. INTRODUCTION
Welding head shield with polypropylene shell and adjustable headband. Features a 2" x 4-1/4" front fl ip lens for quick and easy weld
inspection. Supplied with a shade 10 lens. Conforms to BS EN 175.
3. SPECIFICATION
Model: ..................................................................SSP101.V2
Shade: ............................................................................... 10
4. ASSEMBLY
4.1. ATTACHING THE HEADBAND
4.1.1. Unscrew and remove the thumb wheel on one side of the headband (fi g 1).
4.1.2. Locate the exposed threaded spindle through the fi xing hole in the head shield body (fi g 2).
4.1.3. Clip the tilt tab onto the locating stud on the head shield (fi g 3).
4.1.4. Reattach the thumbscrew and tighten (fi g 4).
4.1.5. Repeat for the other side.
© Jack Sealey Limited
WELDING HEAD SHIELD - SHADE 10
SSP101.V2
MODEL NO:
Original Language Version SSP101.V2 Issue 1 30/11/21