Using The Clearframe™ Feature; (For 46Sl412U, 55Sl412U, And 55S41U); Selecting The Cinema Mode; Using The Film Stabilization Feature - Toshiba 40SL412U Owner's Manual

Selecting the cinema mode

When you view a DVD (3:2 pulldown processed) from
a DVD player connected to the VIDEO, ColorStream HD
(component video), or HDMI inputs on the TV, smoother
motion can be obtained by setting the Cinema Mode to Film.
To set the Cinema Mode to Film:
(available for 480i and 1080i signals)
1無
and open the Picture menu
Press
2無
Highlight Picture Settings and press
3無
Highlight Advance Picture Settings and press
4無
In the Cinema Mode field, select Film.
5無
To save the new settings, highlight Done and press
To revert to the factory defaults, highlight Reset and
press .
To set the Cinema Mode to Video:
Select Video in Step 3 above.
Using the ClearFrame™ feature
(For 46SL412U, 55SL412U, and
55S41U)
The new ClearFrame 120 Hz anti-blur technology doubles
the frame rate from 60 frames per second to 120 frames per
second, virtually eliminating motion blur without adding
flicker or reducing image brightness.
To turn on ClearFrame:
1無
and open the Picture menu, highlight Picture
Press
Settings and press
.
2無
Highlight Advanced Picture Settings and press
3無
In the ClearFrame field, select On.
4無
To save the new settings, highlight Done and press
To revert to the factory defaults, highlight Reset and
press .
Note:
• If you select one of the factory-set picture modes
(Sports, Standard, Movie or PC) and then
change the ClearFrame setting, the picture mode
automatically changes to Preference.
• When ClearFrame is set to Off, the Film
Stabilization feature will not be available (grayed
out and set to Off).
52
Chapter 7: Using the TV's advanced features
.
.
.
.
.

Using the Film Stabilization feature

(For 46SL412U, 55SL412U, and
55S41U)
This feature helps to eliminate video shaking.
To turn on Film Stabilization:
1無
and open the Picture menu, highlight
Press
Picture Settings and press
2無
Highlight Advanced Picture Settings and press
3無
In the Film Stabilization field, select Smooth,
Standard or Off.
4無
To save the new settings, highlight Done and press
To revert to the factory defaults, highlight Reset
and press .
Note:
• If you select one of the factory-set picture
modes (Sports, Standard, Movie or PC) and
then change the Film Stabilization setting,
the picture mode automatically changes to
Preference.
• When ClearFrame is set to Off, Film
Stabilization will be grayed out and set to Off
automatically.
• When slow motion video is present the units will
treat any scrolling text as Film and may cause
a slight jitter of the scrolling text. Tuning Off the
Film Stabilization feature will correct this issue.
Using CableClear
®
reduction
The CableClear digital noise reduction feature
®
allows you to reduce visible interference in your
TV picture. This may be useful when receiving a
broadcast with a weak signal (especially a Cable
channel) or playing a noisy video cassette or disc.
To change the CableClear settings:
1無
and open the Picture menu, highlight
Press
Noise Reduction and press
2無
In the CableClear field, select your desired setting.
Note:
• If the current input is ANT/CABLE, VIDEO,
the menu will display the text "CableClear."
The available selections are Off, Low,
Middle, and High.
• If the current input is ColorStream HD,
HDMI 1, HDMI 2 or HDMI 3, the menu
will display the text "DNR." The available
selections are Off, Low, Middle, and High.
Low, Middle, and High will reduce the noise
in varying degrees, from lowest to highest,
respectively.
.
digital noise
.
(continued)
.
.