Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
3840 x 2160p –24 Hz, 25 Hz, 30 Hz, 50 Hz, 60 Hz • 1. Product information Product information is subject to change without notice. Connectivity detailed product information, please visit www.philips.com/support Common TV Side Common Interface slot: CI+/CAM • Display Type • USB 1 – USB 2.0 Diagonal screen size •...
Page 4
Supported media server software (DMS) • You can use any DLNA V1.5 certified media server software (DMS class). • You can use the Philips TV Remote app (iOS and Android) on mobile devices. Performance may vary, depending on the capabilities of the mobile device and the software used.
Refer to the diversity tables for the correct values. two pins of the Mains/AC Power plug. • The correct component values are listed on the Philips • Check the cabinet for defects, to prevent touching of any Spare Parts Web Portal.
Page 6
• Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to avoid mixed regimes. If this cannot be avoided, carefully clear the solder-joint from old tin and re-solder with new tin.
Page 7
originating from the USA and used e.g. in • Always respect voltages. While some may not be dangerous in themselves, they can cause unexpected LATAM and AP-NTSC countries reactions that are best avoided. Before reaching into a B-TXT Blue TeleteXT powered TV set, it is best to test the high voltage Centre channel (audio) insulation.
Page 8
G-TXT Green TeleteXT distance is 6.5 MHz. L' is Band I, L is all H_sync to the module bands except for Band I High Definition LG.Philips LCD (supplier) Hard Disk Drive Loudspeaker HDCP High-bandwidth Digital Content Protection: LVDS Low Voltage Differential Signalling A “key”...
Page 9
Serial Peripheral Interface bus; a 4-wire module, implementing the CA system for a synchronous serial data link standard host (e.g. a TV-set) S/PDIF Sony Philips Digital InterFace Power On Reset, signal to reset the uP SRAM Static RAM PSDL Power Supply for Direct view LED...
Page 10
Thin Film Transistor toward external amplifier Total Harmonic Distortion Vestigial Side Band; modulation method TMDS Transmission Minimized Differential WYSIWYR What You See Is What You Record: record Signalling selection that follows main picture and Transport Stream sound TeleteXT WXGA 1280 × 768 (15:9) TXT-DW Dual Window with TeleteXT XTAL...
3.2 Assembly/Panel Removal 3.2.1 Stand removal 1. Remove the fixation screws [1] that secure the stand. 2. Take the stand bracket out from the set. (OLED804 Series) 3.2.2 Rear Cover Warning: Disconnect the mains power cord before removing the rear cover. 1.
Page 13
3.2.4 IR Board Control Unit 1. Release the connector from the SSB Board. Caution: be careful, the Keyboard is catch on the Back cover, please be careful to avoid damage the fragile connectors! 2. Remove all the fixation screws from the keyboard control panel [2] and take it out from the Back cover. When defective, replace the whole unit.
Page 14
3.2.6 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. 1. Gently unplug all connectors from the PSU. 2. Remove all fixation screws from the PSU. 3.
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 16
– (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 17
4.3 Factory mode: Purpose To perform extended alignments. Specifications Displaying and or changing Panel ID information. Displaying and or changing Tuner ID information. Error buffer clearing. Various software alignment settings. Testpattern displaying. Public Broadcasting Service password Reset. ...
Page 18
How to Exit CSM To exit CSM, use one of the following methods. Press the MENU/HOME button on the remote control transmitter. Press the POWER button on the remote control transmitter. Press the POWER button on the television set. ...
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading 5.1.1. The following update is for .pkg file. 1. Rename the file to “upgrade_loader.pkg”. 2. Prepare a USB memory (File format: FLAT, Size: 1G~8G). 3. Copy the software to USB flash disk (root directory). 4.
Page 20
Step 2: F/W Upgrade 1. Press [Settings], then Choose [Search for update] in the Settings menu 2. Choose [USB], then press OK. 3. Choose [Identify], then press OK. 4. .Select the file that you downloaded and press OK 5. Identify the software and choose [Done], then choose [Start] on following step...
Page 21
6.Choos [Upadte] press OK start the softwear update. 6. Upgrade in progress Step 3: Check the SW version After burning software, TV will restart Press “123654”, enter Customer Service Mode to check if the software version is correct. Caution: Please make sure that software upgrade is finished before unplug the USB and AC power! 5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set.
Page 22
The last five errors, stored in the NVM, are shown in the Service menu’s. This is called the error buffer. The error code buffer contains all errors detected since the last time the buffer was erased. The buffer is written from left to right. When an error occurs that is not yet in the error code buffer, it is displayed at the left side and all other errors shift one position to the right.
Trouble shooting 2016年12月10日 2016/4/8 Picture-related Intermittent Ask Photo Picture ? problem ? Menu Smarkt Signal SW latest ? Backlight? issue function? issue SSB+LVDS+Panel Update SW LED working ? PSU/SSB Problem solved ? Sound ? PSU+ Panel Finish SW+SSB...
Page 24
Trouble shooting 2016年12月10日 2016/4/8 Audio/Sound- related Intermittent Sound ? problem ? Setting SW latest ? Mute ? issue issue Update SW Extra device Check extra connect? device Problem solved ? Factory setting Finish Sound back ? Setting issue SSB+SPK...
Page 25
6.Slow response to user interaction 7.Switches ON by itself 8.Switches Off by itself 9.Stuck in standby mode / unable to start up 10.Stuck on PHILIPS / ANDROID logo 11.CAM not recognized by TV 12.CAM authentication issue 13.Misc CAM issue 14.IP-EPG issues 15.BC-EPG issues...
7. Electrical Diagram Block diagram 7.2 Power Supply Power architecture of this platform. AUDIO LVDS Platform power Display power CN8601 ON/OFF Platform PS_ON MT5599 12V_A CN1190 AC-input + Main filter AC IN...
Page 56
9-2-22 DCDCd_+2V5 +2V5 Updated on 2018/12/21 FB4504 120R 3A +12V C4542 100NF 16V Updated to C0603 on 2019/1/28 10R 5% R4541 PQ_2.5V C4541 New 18AC : 373G253S383M00 U4503 1uF 16V 100R 5% R4540 PQ_3.3V L4503 3.3uH MP1471AGJ Updated on 2018/12/21 Updated on 2018/12/21 R4542 100K 1%...
Page 57
9-2-23 DCDCb_+1V5 DDR_1.5V Updated on 2019/1/24 FB4505 120R 3A +12V C4551 100NF 16V Updated to C0603 on 2019/1/28 10R 5% R4557 DDR_1.5V New 18AC : 373G253S383M00 C4553 U4504 PQ_3.3V 1uF 16V 100R 5% R4560 L4504 3.3uH MP1471AGJ Updated on 2019/1/24 R4558 91K 1% Vout=0.8*(1+33/36) = 1.533...
Page 58
9-2-24 NT72315_POWER PQ_VDD_DDR_1.5V POWER IF Estimate:244mA DDR IF power cap place near Factual: waiting for test power pin of main chip as close as possible. PQ_Main_DDR_1.5V PQ_VDD_DDR_1.5V R3736 PQ_VBOTX_2.5V PQ_1.5V U3700D R3731 0 OHM 1/8W PQ_2.5V 0 OHM 1/8W PQ_VDD_MMU_1.5V VDD15_DDR_MMU VDD15_DDR_MMU VDD15_DDR_MMU...
9.3 E 715GA039 IR Board 9-3-1 IR&STB LED&Light sensor L i g h t S e n s o r DVD3V3 U222 R 2 2 3 R 2 2 4 R 2 2 5 R 2 2 6 R 2 2 7 R 2 2 8 R 2 2 9 I I C...
9.4 E 715GA334 Keyboard control panel 9-4-1 Key CONN TO SSB JOYSTICK Joystick key define CN03 CN02 CN01 Direction switch Key functionResistance Voltage Range KEY1 Center 2-5 short Menu 0.0 to 0.22 V GND_Key AMBI_SPI_CLK CONN Right 1-5 short 0.5V 0.39 to 0.60 V AMBI_SPI_MOSI 100PF 50V...