Table of Contents
Advertisement
equipment such as gloves to avoid injuries resulting from a high
temperature.
■ When using the product with an extension cord, use a 3 x 1.5mm
heavy duty extension cord only.
■ This machine is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the machine.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise and the operator should pay special attention to
avoid the following:
■ Use the product only for its intended use. Do not alter or modify
the product from the original design or function.
■ Always be aware that misuse and improper handling of the
product can cause injury to yourself and others.
■ Never leave an air compressor unattended with the hose attached
to a tool.
■ Do not continue to use an air compressor or hose which leaks air
or does not function properly.
■ Risk of bursting
– Do not adjust regulator to result in output pressure greater
than marked maximum pressure of attachment.
■ Heat and high temperature are generated while motor and
cylinder are running. Touching exposed metal can result in
serious burns.
– Always keep the air compressor away from the working zones.
■ Injury casued by noise
– Wear ear protection.
■ The gas from air compressor can propel dirt, chips, loose particles
and small objects at high speed. This may result in objects being
thrown into eyes or other possible serious injury.
– Always wear proper personal protective equipment when
operating different tools.
WARNING! Do not remove the NITTO couplers on the product.
Altering the NITTO style couplers which are fixed and sealed on the
product will void your warranty. If you would like to use alternative
style fittings, please use an adaptor for the application.
SPECIFIED CONDITIONS OF USE
This compressor is designed to supply pressurised air only. It must
not be used to compress any other gas. It is designed to operate air
powered tools. The compressor should be operated indoors only.
ASSEMBLY
UNPACKING
This product requires assembly. Carefully remove the product and
any accessories from the box.
WARNING! Do not use this product if any parts on the packing
list are already assembled to your product when you unpack it. Parts
on this list are not assembled to the product by the manufacturer and
require customer installation. Use of a product that may have been
improperly assembled could result in serious personal injury.
Inspect the product carefully to make sure no breakage or damage
occurred during shipping.
8
Do not discard the packing material until you have carefully inspected
and satisfactorily operated the product.
2
WARNING! If any parts are damaged or missing do not operate
this product until the parts are replaced. Use of this product with
damaged or missing parts could result in serious personal injury.
WARNING! Do not attempt to modify this product or create
accessories not recommended for use with this product. Any such
alteration or modification is misuse and could result in a hazardous
condition leading to possible serious personal injury.
WARNING! Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental starting and
possible serious personal injury.
Packing list
– Air compressor
– Front handle
– Front handle locking bolt x 2
– Air filter x 3
– Air hose x 3
– Front wheel x 2
– Rear wheel x 2
– M10 Step bolt x 2
– M10 hex nut x 2
– Ø 10 washer (4mm) x 2
– Ø 10 washer (1.5mm) x 2
– Ø 10 spring washer x 2
– M6 bolt x 8
– M6 hex nut x 8
– Operator's manual
INSTALLING FRONT HANDLE
See figure 2.
1. Insert both ends of the front handle in handle slots.
2. Align the holes on the front handle and handle slots. Secure both
ends with locking bolts and hand tighten.
INSTALLING FRONT WHEELS
See figure 3.
1. Place a front wheel under the left supporting frame at the front.
Align the screw holes.
2. Insert 4 M6 bolts in the holes of the front wheel and the
supporting frame.
3. Secure the front wheel with 4 M6 hex nuts.
4. Repeat the above steps to install the other front wheel on the
right.
5. Ensure the compressor is stable by gently applying lateral force
on it.
INSTALLING REAR WHEELS
See figure 4.
1. Insert an M10 step bolt in the centre hole of the rear wheel.
2. Insert the threaded section of the step bolt in the hole in the rear
brace on the left. Place a 4 mm washer between the wheels and
frame, and place a 1.5 mm washer on the inside of the frame.
3. Secure the step bolt with an M10 spring washer and hex nut.
4. Repeat the above steps to install the other rear wheel on the right.
5. Ensure the compressor is stable by gently applying lateral force
on it.
8
Advertisement
Table of Contents
