Assembly And Adjustments - Black & Decker BEPW1600 Instruction Manual

using more than one extension to make up the total length,
be sure each individual extension contains at least the
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Volts Total length of cord in meters (m)
120 V - 127V 0 - 7
220 V 0 - 15
ampere Rating
Minimal cross‑sectional area of the
More Not
Than More
Than
0 6 1,0
6 10 1,0
10 12 1,5
12 16 2,5
Extension Cords
Use only extension cords that are intended for outdoor
use. These extension cords are identified by a marking
"Acceptable for use with outdoor appliances; store indoors
while not in use." Use only extension cords having an
electrical rating not less than the rating of the product. Do
not use damaged extension cords. Examine extension cord
before using and replace if damaged. Do not abuse extension
cord and do not yank on any cord to disconnect. Keep cord
away from heat and sharp edges. Always disconnect the
extension cord from the receptacle before disconnecting the
product from the extension cord.

WARNING: To reduce the risk of electrocution, keep
all connections dry and OFF the ground. Do not touch
plug with wet hands.
Servicing of Double Insulated Appliances
Your appliance is double‑insulated to give you added
safety. In a double insulated appliance, two systems of
insulation are provided instead of grounding. No grounding
means is provided on a double insulated appliance, nor
should a means for grounding be added to the appliance.
Servicing a double insulated appliance requires extreme
care and knowledge of the system and should be done
only by qualified service personnel. Replacement parts
for a double insulated appliance must be identical to the
parts they replace. A double insulated appliance is marked
with the words double insulated or "double insulation". The
symbol i (square within a square) may also be marked on
the appliance.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
7 - 15 15 - 30
15 - 30 30 - 60
cord in milimeters (mm
1,5 1,5
1,5 2,5
1,5 2,5
4,0 Not Recommended
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
30 - 50
or AC/DC .... alternating or direct
60 - 100
...................... Class II Construction
2 )
n o ....................... no load speed
2,5
n ......................... rated speed
4,0
4,0
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Attaching Handle (Fig. M)
BEPW1600L, BEPW1750
Press the handle
secure with the screws supplied. Do not overtighten.
Attaching Spray Handle (Fig. B)
1. To connect the spray handle
insert the end of the spray handle onto the end of the
spray wand.
2. Press in and turn the spray handle counterclockwise to
lock it into position.
Attaching High Pressure Hose (Fig. C)
NOTICE: Never pull high pressure hose or water supply
hose to move pressure washer. This could damage hose
and/or pump inlet and/or pump outlet.
1. To connect the high pressure hose
spray handle
while clicking the hose end
Release the hose connect button when the hose end has
clicked into position.
2. To connect the high pressure hose to the pressure
washer unit
PSI....................... pounds per square
minute
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
..................... wear eye protection
current
..................... wear hearing
(double insulated)
never direct the water jet at
people, animals, the machine or
electric components
18 onto the pressure washer unit
4 to the spray wand
, depress the hose connect button
4
into the spray handle.
23
16 , screw the hose collar
ENgLIsh
inch
do not stare into
the light
protection
protection
read all documentation
16 and
2 ,
to the
1
13
23 onto the high
27