Advertisement
EnGlISh
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit
from the support that Philips offers, register your product at www.philips.
com/welcome.
General description (Fig. 1)
Spray nozzle
A
Cap of filling opening
B
Steam control
C
-
O = no steam
-
l = minimum steam
-
; = maximum steam
-
1 = Calc-Clean function
Shot-of-steam button 9 (all types except GC2510)
D
Spray button T
E
Automatic shut-off light (GC2560 only)
F
Mains cord
G
Anti-Calc tablet (all types except GC2522/GC2510)
H
Temperature light
I
Type plate
J
Water tank
K
Temperature dial
L
Important
Read this user manual carefully before you use the appliance and save it for
future reference.
Danger
-
Never immerse the iron in water.
Warning
-
Check if the voltage indicated on the appliance corresponds to the local
mains voltage before you connect the appliance.
-
Do not use the appliance if the plug, the mains cord or the appliance
itself shows visible damage, or if the appliance has been dropped
or leaks.
-
If the mains cord is damaged, you must have it replaced by Philips, a
service centre authorised by Philips or similarly qualified persons in
order to avoid a hazard.
-
Never leave the appliance unattended when it is connected to the
mains.
-
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
-
Children should be supervised to ensure that they do not play with the
appliance.
-
Do not let the mains cord come into contact with the hot soleplate of
the iron.
Caution
-
If the appliance has an earthed plug, it must be plugged into an earthed
wall socket.
-
Check the mains cord regularly for possible damage.
-
The soleplate of the iron can become extremely hot and may cause
burns if touched.
-
When you have finished ironing, when you clean the appliance, when
you fill or empty the water tank and also when you leave the iron even
for a short while: set the steam control to position O, put the iron on its
heel and remove the mains plug from the wall socket.
-
Always place and use the iron on a stable, level and horizontal surface.
-
Do not put perfume, vinegar, starch, descaling agents, ironing aids or
other chemicals in the water tank.
-
This appliance is intended for household use only.
Electromagnetic fields (EMF)
This Philips appliance complies with all standards regarding electromagnetic
fields (EMF). If handled properly and according to the instructions in this
user manual, the appliance is safe to use based on scientific evidence
available today.
Before first use
Remove any sticker or protective foil from the soleplate.
1
Let the iron heat up to maximum temperature and pass the iron over
2
a piece of damp cloth for several minutes to remove any residues
from the soleplate.
2
Preparing for use
Filling the water tank
Do not put perfume, vinegar, starch, descaling agents, ironing aids,
chemically descaled water or other chemicals in the water tank.
Switch off the appliance and unplug it.
1
Set the steam control to position O (= no steam) (Fig. 2).
2
Open the cap of the filling opening.
3
Tilt the iron and fill the water tank up to maximum level under the
4
tap (Fig. 3).
Note: Do not fill the water tank beyond the MAX indication.
Note: If the tap water in your area is very hard, we advise you to use distilled
water. Do not use chemically descaled water.
Close the cap of the filling opening ('click').
5
Setting the temperature
Put the iron on its heel (Fig. 4).
1
To set the required ironing temperature, turn the temperature dial to
2
the appropriate position.
Check the laundry care label for the required ironing temperature.
-
1 Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester)
-
1 Silk
-
2 Wool
-
3 Cotton, linen
If you do not know what kind or kinds of fabric an article is made of,
determine the right ironing temperature by ironing a part that is not visible
when you wear or use the article.
Silk, woollen and synthetic materials: iron the reverse side of the fabric to
prevent shiny patches. Avoid using the spray function to prevent stains. Start
ironing the articles that require the lowest ironing temperature, such as
those made of synthetic fibres.
Plug in the appliance. If the appliance has an earthed plug, put the
3
mains plug in an earthed wall socket.
The temperature light goes on.
,
When the temperature light goes out, wait a while before you start
4
ironing.
During ironing, the temperature light goes on from time to time. This
,
indicates that the iron is heating up to the set temperature.
Using the appliance
Note: The iron may give off some smoke when you use it for the first time. This
stops after a short while.
Steam ironing
Make sure that there is enough water in the water tank.
1
Set the recommended ironing temperature (see chapter 'Preparing
2
for use', section 'Setting the temperature').
Set the appropriate steam setting. Make sure that the steam setting is
3
suitable for the ironing temperature selected: (Fig. 2)
-
ç for minimum steam (temperature settings 2 and 3).
-
é for maximum steam (temperature settings 3 to MAX).
Note: The iron starts to produce steam as soon as it has reached the set
temperature.
GC2640/GC2620/GC2530/GC2528/GC2520/GC2510 only:
Water may leak from the soleplate if the set temperature is too low (MIN
to 2).
Ironing without steam
Set the steam control to position O (= no steam).
1
Set the recommended ironing temperature (see chapter 'Preparing
2
for use', section 'Setting the temperature').
Features
Spray function
You can use the spray function at any temperature to moisten the article to
be ironed. This helps remove stubborn creases.
Make sure that there is enough water in the water tank.
1
4239.000.6144.8
Advertisement
