Sealey WL483D Instructions

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
instruction
manual
1. SAFetY
electricAl SAFetY
1.1.
wArning! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey stockist.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable
Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. imPortAnt: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
do not pull or carry the appliance by the power cable.
8
do not pull the plug from the socket by the cable.
8
do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is
8
replaced immediately by a qualified electrician.
8
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
2. introduction
i
Powerful 3 diopter 120mm precision lens gives high quality magnifying capabilities. features 48 smd leds to illuminate the object for improved
detailed work. multi-position swing arm allows simple positioning of lamp to suit task. features a G-clamp base to secure to a workbench or
table. Ideal for electrical engineers, engravers and fine detail work.
3. SPeciFicAtion
i
model no:................................................................ wl483d
leds: ........................................................................ 48 smd
supply: ...........................................................................230V
4. oPerAtion
4.1. mounting
4.1.1. Fix the clamp to a secure surface. See fig.1.
4.1.2. lower the work light assembly into the clamp, use two
hands to prevent the lamp moving during this operation.
4.1.3. Turn on/off using the switch on top. See fig.2.
4.1.4. Adjust by loosening/tightening the head clamp. See fig.3.
note: Be aware of the effect of using the lamp close
to a window/door where it could be in direct sunlight.
remember to close the lid on top whilst it is not in use.
© Jack sealey limited
instructions for
bench mounted worklight
wl483d
model no:
fig.1
Original Language Version
recommended fuse rating
3 AmP
fig.2
WL483D Issue 2 (H,F) 11/01/18