TH-L32C10R2 1 Safety Precautions 1.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
TH-L32C10R2 2 Prevention Electro Static Discharge (ESD) Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field- effect transistors and semiconductor “chip”...
TH-L32C10R2 3 About Lead Free Solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead Solder and PbF will refer to Lead Free Solder. The Lead Free Solder (PbF) used in our manufacturing process and discussed below is (Sn+Ag+Cu).
TH-L32C10R2 4 Power LED Blinking Timing 1. Subject Information of LED Flashing timing. 2. Contents When an abnormality occurs, the protection circuit will operate and reset the unit to stand by mode. During this time, the defective block can be identified by the number of blinking times of the Power LED on the front panel of the unit as follow:...
TH-L32C10R2 5 Chassis Board 5.1. Chassis Installation 1. Stick FELT to SIDE AV BRACKET. - Stick the SIDE AV INDI. SHEET on the SIDE AV BRACKET. - Insert the SIDE AV BRACKET from the side position of the A-PCB.
Page 10
TH-L32C10R2 6 Location of Controls and Components 6.1. Wire Dressing 1. Wiring No. 1 ~ No.7 2. Remove dust of terminal of LVDS and PB connector. (by ion blow) Pos. A11 3. Insert LVDS into A11. Clamper Wire No.1 A10 ~ V10 No.2 A01 ~ K01...
Page 11
TH-L32C10R2 7 Disassembly and Assembly Instructions 7.1. AC Cord Installation 1. Put on the AC CORD BRACKET on the CABINET. 2. Fix the AC CORD BRACKET with SCREW. 3. AC CORD BARRIER setting. 4. Insert AC CORD connector into P-PCB connector.
Page 12
TH-L32C10R2 7.2. VESA Metal Assembly 1. Assemble LCD TOP MTG(L,R), VESA METAL(upper) and fix them with screw. Please use jig for vesa metal assembly preparation.
Page 13
TH-L32C10R2 7.3. VESA (BC) Installation 1. Put VESA METAL(BC) on the BACK COVER. 2. Fix them with SCREWS.
Page 14
TH-L32C10R2 7.4. Pedestal Assembly Step 1 Setting BASE PLATE and PEDESTAL COVER with SCREWS. Step 2 1. Stick the RUBBER FOOT at bottom PEDESTAL COVER and BASE PLATE. 2. RUBBER FOOT (TBL4GG3008 - 2 pcs) stick at BASE PLATE. 3. RUBBER FOOT (TBL4GG3009 - 2 pcs) stick at bottom PEDESTAL COVER.
Page 15
TH-L32C10R2 7.5. LED Panel Installation & Fitting 1. Put LED SHADE RIB on CABINET. 2. Fix LED PANEL on CABINET. 3. Wire connecting. (V10) 4. Put V-PCB on CABINET. 5. Fix them with SCREW. 6. Insert the CLAMPER.
Page 16
TH-L32C10R2 7.6. Control Panel Assembly 1. Wire connecting. (K1) 2. Assemble POWER BUTTON to the K-PRINT. 3. Assemble K-PRINT, CONTROL BUTTON, CONTROL PANEL BRACKET. 4. Fix them with SCREWS. 5. Stick the FELT.
Page 17
TH-L32C10R2 7.7. A-PB-MTG & Control Button Fixing 1. Stick P-PCB BARRIER and put all METAL part follow to the picture. Fix all metal part with screw. 2. Put CONTROL PANEL ASSY on the CABINET. Fix the CONTROL PANEL with SCREWS.
Page 18
TH-L32C10R2 7.8. Side AV Bracket Assembly • STICK FELT TMK4G028 (7 X 240 X 0.55t) - 2 PCS.
Page 19
TH-L32C10R2 7.9. Speaker Installation 1. Stick the SPONGE. Follow the spec. below. 2. SP BRACKET slot at CABINET. 3. Insert the SP RUBBER BUSH into the SP UNIT. 4. Insert the SP UNIT to SP BRACKET. 5. Fix them with SCREWS.
Page 20
TH-L32C10R2 7.10. LCD Panel 1. Remove dust of terminal of LVDS. (by ion blow) 2. Remove dust of terminal of T-con connector. (by ion blow) 3. Insert LVDS into T-con connector. 4. Stick the tape to fix LVDS. 5. Stick the SPONGE at left and right lcd panel.
Page 21
TH-L32C10R2 7.11. LCD Mouting Fixing Step 1 1. LCD SIDE MTG on the CABINET. 2. LCD BTM MTG on the CABINET. 3. LCD BOTTOM CORNER MTG on the CABINET. 4. Fix them with SCREW. Step 2 1. Assemble LCD TOP MTG (L, R), VESA METAL (upper) and fix them with SCREWS.
Page 22
TH-L32C10R2 7.12. LCD Panel Assembly Installation 1. Put LCD panel to cabinet assembly.
Page 23
TH-L32C10R2 7.13. EMI Spec (LVDS) 1. When insert LVDS wire to T-con conector, make sure must center position follow below picture. 2. After fixing LVDS wire please bent again follow the picture.
Page 24
TH-L32C10R2 7.14. Back Cover Assembly (Felt Sticking) Stick the FELT.
Page 25
TH-L32C10R2 8 Service Mode Adjustment Set timer to 30min, press the “RECALL” button on the remote control and press “-” vol button on the LCD panel. • Press button R and G for adjustment. 8.1. Self Check Mode 1. Press the “MENU” button (on the remote control) and the “DOWN” button on the LCD panel.
Page 26
TH-L32C10R2 9 Measurements and Adjustments 9.1. Voltage Chart of A Board Set A-Board to a dummy set and check the satisfaction with the specified voltage as following table. Specification (V) Power Supply Name Measurement Point TNP4G460 / TNP4G461 SUB1.2V TP5602 1.22 - 1.32...
Page 27
TH-L32C10R2 10 Printed Circuit Board 10.1. A-Board A-Board (A Side) TNP4G460 Parts Location Ref. No Location Ref. No Location Ref. No Location Ref. No Location IC1100 IC5441 IC8404 D3015 IC1101 IC5480 IC8405 D4513 IC2750 IC5600 IC8408 D4617 IC2901 IC5601 IC8409...
Page 28
TH-L32C10R2 10.2. A-Board A-Board (B Side) TNP4G460 Parts Location Ref. No Location Ref. No Location Ref. No Location Ref. No Location IC2008 IC4512 IC8002 D3015 IC2301 IC5409 IC8003 IC4510 IC5451 IC8403 IC4511 IC8001 IC8411...
Page 29
TH-L32C10R2 11 Schematic Diagram 11.1. Schematic Diagram Notes Notes : 1. Resistor Unit of resistance is OHM [Ω] (K = 1 000, M = 1 000 000). 2. Capacitor Unit of capacitance is μF unless otherwise noted. 3. Coil Unit of inductance is μF unless otherwise noted.
Page 30
TH-L32C10R2 11.2. A Board 11.2.1. A Board - Sheet : 001 (1 / 1)
Page 108
TH-L32C10R2 12 Exploded View and Replacement Parts List 12.1. Exploded View and Mechanical Replacement Parts List Please click the radio button for “Diagrams ll/Parts List” on the menu bar. 12.2. Electrical Replacement Parts List 12.2.1. Replacement Parts List Notes Important Safety Notice Components identified by mark have special characteristics important for safety.
Page 109
TH-L32C10R2 12.2.2. Electrical Replacement Parts List Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks C2266 F1G1H101A565 CERAMIC CAPACITOR C2301 F1G1C104A116 CERAMIC CAPACITOR CAPACITORS C2302 F1G1C104A116 CERAMIC CAPACITOR C1009 F1G1A105A047 CAPACITOR...
Page 110
TH-L32C10R2 Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks C3007 F1G1H561A730 CHIP CAPACITOR C4617 F1J1A475A039 CERAMIC CAPACITOR C3008 F1G1H561A730 CHIP CAPACITOR C4624 F1G1C104A116 CERAMIC CAPACITOR C3013 F1G1H561A730 CHIP CAPACITOR C4625...
Page 111
TH-L32C10R2 Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks C8001 F1G1C104A116 CERAMIC CAPACITOR C8078 F1G1C104A116 CERAMIC CAPACITOR C8002 F1H0J1050012 CERAMIC CAPACITOR C8079 F1G1C104A116 CERAMIC CAPACITOR C8003 F1H0J1050012 CERAMIC CAPACITOR C808...
Page 112
TH-L32C10R2 Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks D2752 EZJZ0V120JA VARISTOR IC2301 C1AB00002875 IC D2760 MAZ81400ML DIODE IC2750 C1ZBZ0003577 IC D2779 MA22F2000L DIODE IC2902 C0DBGYY00281 IC D4202 MA2J11100L DIODE...
Page 113
TH-L32C10R2 Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks L4518 J0JYC0000068 COIL Q5601 B1MBDDA00003 TRANSISTOR L4519 J0JYC0000068 COIL Q5602 B1MBDDA00003 TRANSISTOR L5430 J0JHC0000045 COIL Q804 2SD0601A0L TRANSISTOR L5443 G1C470MA0077 COIL...
Page 114
TH-L32C10R2 Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks R1108 ERJ2GEJ101X RESISTOR R2316 EXB28V220JX RESISTOR R1109 ERJ2GEJ101X RESISTOR R2325 ERJ2GE0R00X FIXED RESISTOR R1146 ERJ2GEJ102X FIXED RESISTOR R2500 ERJ2RKF3000X RESISTOR R1153...
Page 115
TH-L32C10R2 Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks R3138 ERJ2GEJ820X RESISTOR R4529 ERJ2GEJ103X FIXED RESISTOR R3139 ERJ2GEJ820X RESISTOR R4530 ERJ2GEJ103X FIXED RESISTOR R3140 ERJ2GEJ820X RESISTOR R4531 ERJ2GEJ103X FIXED RESISTOR...
Page 116
TH-L32C10R2 Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks R5408 ERJ2GEJ473X FIXED RESISTOR R8024 ERJ2GE0R00X FIXED RESISTOR R5409 ERJ2GEJ103X FIXED RESISTOR R8025 ERJ2GE0R00X FIXED RESISTOR R5410 ERJ2GEJ103X FIXED RESISTOR R8026...
Page 117
TH-L32C10R2 Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks R822 ERJ3EKF6340 M 634OHM,F,1/16W R8660 ERJ2GE0R00X FIXED RESISTOR R823 D0GD103JA017 FIXED RESISTOR R867 ERJ6ENF1801 M 1.8KOHM, 1/10W R824 D0GD393JA017 FIXED RESISTOR...
Page 118
TH-L32C10R2 Safety Ref. Part No. Part Name & Description Remarks Safety Ref. Part No. Part Name & Description Remarks R8904 ERJ2GEJ103X FIXED RESISTOR SW2605 K0H1BA000445 CONNECTOR R8905 ERJ2GEJ103X FIXED RESISTOR TU2901A ENG39E04GRF TUNER R8906 ERJ2GEJ103X FIXED RESISTOR K1KA07B00135 CONNECTOR R8907...
Page 119
Model No. : TH-L32C10R2 Parts Location...
Page 120
Model No. : TH-L32C10R2 Packing Exploded View...
Page 121
Model No. : TH-L32C10R2 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks K2CQ2YY00036 AC CORD L0AA14B00003 SPEAKER UNIT L5EDD8Q00060 LCD PANEL N2QAYB000399 REMOTE CONTROL TBL4GA0028 PEDESTAL ASSY TBM4GA002 PANASONIC LOGO SHEET TBM4GC407 MODEL NAME PLATE TBM4GU032...