SA-HT730GCP 1 Use of Active Subwoofer 1.1. Checking Player when Active Subwoofer is not used 1. This unit uses the active subwoofer to supply the power of the component, and the active subwoofer should be connected to the component to check operational conditions of the component.
SA-HT730GCP 2 Safety Precautions 2.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
SA-HT730GCP Caution Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
SA-HT730GCP 6 Precaution of Laser Diode CAUTION : This product utilizes a laser. Invisible laser radiation is emitted from the optical pick up lens when the unit is turned on. Wavelength : 662nm(DVD)/785nm(VCD/CD) Maximum output radiation power from pick up : 100µW/VDE Laser radiation from pick up unit is safety level, but be sure the followings: 1.
Page 8
SA-HT730GCP 8 General Description 8.1. Operating instructions TUNING H.BASS OPEN/CLOSE Standby/on indicator PROGRESSIVE DISC EXCHANGE CD MODE DISC SKIP INPUT SELECTOR Remote control Direct select button/indicators signal sensor TUNE MODE FM MODE PHONES VOLUME MEMORY SYSTEM TUNER/BAND TV/VIDEO DVD/CD DISC...
Page 9
SA-HT730GCP 8.2. Disc information Discs that can be played Indication in Disc Logo Remarks these operating instructions Recorded with devices using Version 1.1 of the Video Recording Format (a unified video recording standard), such as DVD video recorders, DVD video cameras, personal computers, etc.
Page 10
SA-HT730GCP 8.3. About HighMAT 8.3.1. What’s HighMAT? Consumers worldwide are using PCs to create their own collections of music, photos and even video by burning them onto CDs. But how these collections can be experienced across different devices can be confusing to navigate, time consuming to access for a DVD player, and be incomplete in terms of music information available to the customer.
Page 11
SA-HT730GCP 8.3.2. Why take advantage of HighMAT? A Problem Defined:Today, when consumers create their own digital audio, video or photo collections on CD-R or other physical formats, there are numerous, inconsistent ways that devices read the data. For the consumer, the playback experience can be...
Page 12
SA-HT730GCP Conventional HighMAT Even though DVD player is CD-R/RW compatible, the inconsistent ways HighMAT compatible products play content back with consistent that various DVD players can read the music or photos files often leads interface. This includes products which are JPEG compatible products to a confusing and inconsistant playback experince.
Page 13
SA-HT730GCP HighMAT is now available for CD Burning and in Leading DVD Players HighMAT is a new technology that is now available in leading software and consumer electronic devices to dramatically improve the digital media experience when you create homemade CDs HighMAT delivers a simple, standardized way for PC software and consumer electronics devices to talk to each other and work better together.
Page 14
SA-HT730GCP When you create your homemade CDs with software that supports HighMAT CD burning, and then play them back on a DVD player that supports HighMAT, you get better, easier navigation. You get folders you can access with a single click of your DVD player´s remote control.
Page 15
SA-HT730GCP 9 Accessories AC cord Remote control System cable AM loop antenna AC plug adapter FM indoor antenna Speaker label Video Cable...
Page 16
SA-HT730GCP 10 Handling Precautions for Optical Pickup Unit The laser diode in the optical pickup unit may break down due to static electricity of clothes or human body. Special care must be taken avoid to electrostatic breakdown when servicing and handling the laser diode.
Page 18
SA-HT730GCP 11 Disassembly and Main Component Replacement Procedure “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components.
Page 20
SA-HT730GCP 11.2. Main Components and P.C.B. Locations...
Page 21
SA-HT730GCP 11.3. Disassembling the Top Cabinet Step 1 Remove 7 screws. Step 2 Remove the top cabinet in the direction of arrow. Step 6 Remove the front panel in the direction of arrow. 11.4. Disassembling the Front Panel Step 7 Remove panel angle.
Page 22
SA-HT730GCP 11.5. Disassembling the Tray 11.7. Disassembling the Main Assembly P.C.Board · Follow the (Step 1) - (Step 2) of Item 11.3. · Follow the Item 11.6. · Follow the (Step 1) - (Step 6) of Item 11.4. Step 1 Unlock the claw and remove 9 screws.
Page 23
SA-HT730GCP 11.8. Removal of the Tray Base Guide (L) and Tray Base Guide · Follow the (Step 1) - (Step 2) of Item 11.3. · Follow the (Step 1) - (Step 6) of Item 11.4. · Follow the (Step 1) - (Step 2) of Item 11.5.
Page 24
SA-HT730GCP Step 3 Rotate close lock gear to direction of arrow, press claw (b) and pull out close lock gear. 11.12. Removal of the Tray Motor Step 2 Flip the base mecha unit in vertical position. P.C.B. and Sensor P.C.B.
Page 25
SA-HT730GCP · Follow the (Step 1) - (Setp 3) of Item 11.6. Step 1 Release the claw in the direction of arrow (1), and then push drive gear shaft up. Step 3 Release the 2 claws in the direction of arrow (1), and Step 2 Remove Drive Gear (A) and Drive Gear (B).
Page 26
SA-HT730GCP 11.18. Removal of the Cam Gear & Support Piece · Follow the (Step 1) - (Step 2) of Item 11.3. · Follow the (Step 1) - (Step 6) of Item 11.4. · Follow the (Step 1) - (Step 2) of Item 11.5.
Page 27
SA-HT730GCP 11.20. Assembly of Tray Base · Follow the (Step 1) - (Step 2) of Item 11.3. · Follow the (Step 1) - (Step 6) of Item 11.4. · Follow the (Step 1) - (Step 2) of Item 11.5. Step 1 Rotate cam gear anti-clockwise. Align at position (C) as marking on gear with arrow.
Page 28
SA-HT730GCP 12 Service Position Prepare service tools before proccess service position. Service Tools Loading Motor P.C.B - Main REEX0465 (11 pin) P.C.B 12.1. Checking & Repair Tray Motor P.C.B and Sensor P.C.B · Follow the (Step 1) - (Step 2) of Item 11.3.
Page 29
SA-HT730GCP 13 Optical Pick-up Self-Diagnosis and Replacement Procedure 13.1. Optical Pickup Breakdown Diagnosis The optical pickup self-diagnosis function and tilt adjustment check function have been included in this unit. When repairing, use the following procedure for effective Self-diagnosis and tilt adjustment.Be sure to use the self-diagnosis function before replacing the optical pickup when "NO DISC"...
Page 30
SA-HT730GCP 13.2. Service Mode Table 1 The service modes can be activated by pressing various button combination on the player and remote control unit. Player buttons Remote control unit buttons Application Note STOP Error code display (Refer to the item, “13.3.
Page 31
SA-HT730GCP Error Code Error Content Additional error explanation F890 Sending message when message is Sending message to AV task being sent to AV task F891 Message couldn’t be sent to AV task Begin sending message to AV task F893 FROM falsification...
Page 32
SA-HT730GCP 13.4. Service mode table 2 Pressing various button combinations on the player and remote control unit can activate the service modes.
Page 34
SA-HT730GCP 13.5. Sales demonstration lock function This function prevents discs from being lost when the unit is used for sales demonstrations by disabling the disc eject function. "LOCKED" is displayed on the unit, and ordinary operation is disabled. 13.5.1. Setting ·...
Page 35
SA-HT730GCP 14 Self-Diagnosis Function 14.2. Memorized Error Codes 14.2.1. Activating Self-Diagnosis Function 14.1. Automatic Displayed Error and Displaying Method Codes 1. Turn on the power. 14.1.1. Automatic Display Function 2. Select DVD/CD function. With no DVD/CD inserted in the player, press and hold down the F_SKIP button For a power unit error, the code is automatically displayed.
Page 36
SA-HT730GCP 15 Service Precautions 15.1. Recovery after the DVD player is repaired · When FLASH ROM IC or DVD module P.C.B. is replaced, carry out the recovery processing to optimize the drive. Playback the recovery disk to process the recovery automatically.
Page 37
SA-HT730GCP 16 Adjustment Procedure 16.1. Service Tools and Equipment Application Name Number Tilt adjustment DVD test disc DVDT-S20 [SPG] TORX screw driver (T6) Available on sales route. (T6) or RFKZ0185 [SPG] Others Grease RFKXPG641 [SPG] Confirmation CD test disc PVCD-K06 or any other commercially...
Page 38
SA-HT730GCP 16.4. Optical adjustment 16.4.1. Optical pickup tilt adjustment Measurement point Adjustment point Mode Disc Tangential adjustment screw T01 (inner periphery) play DVDT-S20 [SPG] Tilt adjustment screw T30 (center periphery) T43 (outer periphery) play Measuring equipment Adjustment value None (Main unit display for servicing is used.) Adjust to the minimum jitter value.
Page 39
SA-HT730GCP 17 Abbreviations INITIAL/LOGO ABBREVIATIONS INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ERROR TORQUE CONTROL ACLK AUDIO CLOCK ERROR TORQUE CONTROL AD0~UP ADDRESS BUS REFERENCE ADATA AUDIO PES PACKET DATA ENCSEL ENCODER SELECT ADDRESS LATCH ENABLE ETMCLK EXTERNAL M CLOCK (81MHz/40.5MHz) AMUTE AUDIO MUTE...
Page 40
SA-HT730GCP INITIAL/LOGO ABBREVIATIONS INITIAL/LOGO ABBREVIATIONS READ ENABLE VBLANK V BLANKING RFENV RF ENVELOPE COLLECTOR POWER SUPPLY RF PHASE DIFFERENCE OUTPUT VOLTAGE (CD-ROM) REGISTER SELECT VCDCONT VIDEO CD CONTROL (TRACKING RSEL RF POLARITY SELECT BALANCE) RESET DRAIN POWER SUPPLY VOLTAGE RESERVE...
Page 41
SA-HT730GCP 18 Voltage Chart 18.1. DVD Module P.C.B. Re f No. IC8001 MODE CD P LAY IC8001 Re f No. MODE CD P LAY IC8001 Re f No. MODE CD P LAY IC8001 Re f No. MODE CD P LAY IC8001 Re f No.
Page 42
SA-HT730GCP 18.2. Main P.C.B. Re f No. IC2006 MODE CD P LAY S TANDBY IC2007 Re f No. MODE CD P LAY S TANDBY IC2008 Re f No. MODE CD P LAY S TANDBY IC2010 Re f No. MODE CD P LAY -6.7...
Page 43
SA-HT730GCP Q2000 Q2001 Q2002 Q2004 Q2028 Re f No. MODE CD P LAY S TANDBY Q2102 Re f No. Q2029 Q2103 MODE CD P LAY -4.5 -4.5 S TANDBY Q2104 Q2105 Q2200 Re f No. MODE CD P LAY -4.3 -4.3...
Page 45
SA-HT730GCP 20 Schematic Diagram Notes · This schematic diagram may be modified at any time Caution! with the development of new technology. IC and LSI are sensitive to static electricity. Notes: Secondary trouble can be prevented by taking care during...
Page 48
DAC3 OUT DQ15 EXADR17 EXADR18 ADDRESS EXADR19 EXADR20 IC8691 C0JBAA000346 AND GATE DVD CLK OP CPU CLK NEXOE NEXWE NEXCE OP CPU CMD DVD CMD MDQ16 IC8695 C0JBAA000346 AND GATE DVD STAT OP CPU STAT DATA MDQ31 SA-HT730GCP BLOCK DIAGRAM...
Page 49
SHIFT REGISTER LATCH POWER ON RESET DVD CLK DVD CLK DVD CMD DVD CMD DVD STAT DVD STAT ST/DO IC2018 TUN DO TUN DI MN101C49GHB TUN SD SYSTEM CONTROL TUN FMDET TUN CLK POWER SUPPLY (FM:ON) (FM) SA-HT730GCP BLOCK DIAGRAM...
Page 66
SA-HT730GCP A A A A TRAY MOTOR P.C.B. LOADING MOTOR P.C.B. (REP3466A) (REP3465A) M9101 Q9102 M9001 SENSOR P.C.B. (REPX3466A) Q9103 CN9102 SA-HT730GCP LOADING MOTOR/TRAY MOTOR/SENSOR P.C.B.
Page 67
DVD MODULE P.C.B. (SIDE:A) CN2009 M9101 SENSOR P.C.B. TRAY MOTOR CN9102 P.C.B. CN2010 MAIN P.C.B. CN2004 SPINDLE 47 50 MOTOR ASS'Y FP8201 LOADING MOTOR P.C.B. M9001 TUNER PACK UNIT DVD MODULE P.C.B. (SIDE:B) JK2001 JK2000 AV JACK ACTIVE SUBWOOFER SA-HT730GCP WIRING CONNECTION...
Page 70
SA-HT730GCP 26 Terminal Function of ICs 26.1. IC2018 (MN101C49GHB): Terminal Function Name Operation CPU MUTE_HP Mute signal output for Headphone Not used Terminal Function TU_SD Tuner signal detect input Name TU_ST/DO Stereo indicator from Tuner/ DO output AVSS - Power supply for A/D converter...
Page 71
SA-HT730GCP 27 Parts Location and Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety purpose. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used.
Page 72
SA-HT730GCP 27.1. Loading Mechanism, Traverse Unit & Cabinet 27.1.1. Loading Mechanism, Traverse Unit & Cabinet Parts Location...
Page 75
SA-HT730GCP 27.1.2. Traverse and Cabinet Parts List Ref. Part No. Part Name & Description Remarks RMS0789 FIXED PIN Ref. Part No. Part Name & Description Remarks RMS0802-J DRIVE GEAR SHAFT XTN26+14JFJK SCREW CABINET AND CHASSIS XTV2+6GFJ PCB SCREW XWG6FFY WASHER...
Page 76
SA-HT730GCP 27.2. Component Parts List Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks PRINTED CIRCUIT BOARDS Q2809 B1ACKD000005 TRANSISTOR Q2811 B1BCCG000023 TRANSISTOR REP3867A DVD MODULE P.C.B Q2812 B1ABCE000016 TRANSISTOR (RTL) Q2813 B1AAKD000014...
Page 77
SA-HT730GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks D6900 B3AAA0000583 DIODE CONNECTORS D6901 B3ABA0000397 DIODE D6902 B3ABA0000397 DIODE CN2002 K1KA10AA0031 10P CONNECTOR D6903 B3ABA0000397 DIODE CN2004 K1MN50A00008 50P CONNECTOR D6904 B3ABA0000397...
Page 78
SA-HT730GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks JK6801 K2HC103A0024 W2061 ERJ3GEY0R00V CHIP RESISTOR W2062 ERJ3GEY0R00V CHIP RESISTOR EARTH TERMINAL W2064 ERJ6GEY0R00V CHIP RESISTOR W2065 ERJ6GEY0R00V CHIP RESISTOR E2000 K4CZ01000027 TERMINALS...
Page 79
SA-HT730GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2035 ERJ3GEYJ221V 220 1/16W R2154 ERJ3GEYJ222V 2.2K 1/16W R2037 ERJ3GEYJ221V 220 1/16W R2155 ERJ3GEYJ104V 100K 1/16W R2038 ERJ3GEYJ221V 220 1/16W R2156 ERJ3GEYJ103V 10K 1/16W...
Page 80
SA-HT730GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2403 ERJ3GEYJ473V 47K 1/16W R2658 ERJ3GEYJ392V 3.9K 1/16W R2404 ERJ3GEYJ822V 8.2K 1/16W R2659 ERJ3GEYJ182V 1.8K 1/16W R2405 ERJ3GEYJ102V 1K 1/16W R2660 ERJ3GEYJ102V 1K 1/16W...
Page 81
SA-HT730GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2905 ERJ3GEYJ1R0V 1 1/16W R8311 ERJ2RHD242X 2.4K 2W R2971 ERJ3GEY0R00V 0 1/16W R8312 ERJ2RHD102X 1K 2W R2972 ERJ3GEY0R00V 0 1/16W R8313 ERJ2RHD243X 24K 2W...
Page 82
SA-HT730GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks CAPACITORS C2176 ECJ1VB1H471K 470P 50V C2177 ECJ1VB1H471K 470P 50V C2003 ECEA1AKA220B 22 10V C2179 EEUFM1A681B 680P 10V C2004 ECJ1VB1E103K 0.01 25V C2200 ECJ1VB1C393K 0.039 16V...
Page 83
SA-HT730GCP Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C2609 ECJ1VB1H562K 5600P 50V C2862 ECJ1VB1C104K 0.1 16V C2610 ECEA1HKA100B 10 50V C2863 ECEA1CKA221B 220 16V C2611 ECEA1HKA4R7I 4.7 50V C2866 ECJ1VB1A105K 1 10V...
Page 85
SA-HT730GCP 27.3. Packing Materials & Accessories Parts List Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks A1-1 UR76EC3103A R/C BATTERY COVER PACKING MATERIALS K2CQ2CA00002 AC CORD RQT7974-M OI BOOK [SP] RPGX1389 PACKING CASE...
Page 86
SA-HT730GCP 28 Schematic Diagram for printing with letter size...
Page 87
SA-HT730GCP 22 Schematic Diagram SCHEMATIC DIAGRAM-1 DVD MODULE CIRCUIT :+B SIGNAL LINE :CD-DA SIGNAL LINE :MAIN SIGNAL LINE :DVD(VIDEO) SIGNAL LINE FP8101 VGND LB8303 J0JCC0000119 Y/PY/G VGND LB8304 J0JCC0000119 CB/PB/B VGND LB8305 J0JCC0000119 CR/PR/R VGND LB8301 J0JCC0000119 VGND LB8302 J0JCC0000119...
Page 89
SA-HT730GCP SCHEMATIC DIAGRAM-2 DVD MODULE CIRCUIT :+B SIGNAL LINE :CD-DA SIGNAL LINE :DVD(VIDEO) SIGNAL LINE :DVD(AUDIO) SIGNAL LINE LB8001 J0JHC0000045 LB8002 J0JHC0000045 C8002 C8001 C8028 C8027 C8026 C8025 C8024 4V330 6V100 2200P C8004 RX8014 82X4 MDQ 7 MDQ 8 MDQ 6...
Page 93
SA-HT730GCP SCHEMATIC DIAGRAM-4 MAIN CIRCUIT :+B SIGNAL LINE :-B SIGNAL LINE :MAIN SIGNAL LINE :DVD(VIDEO) SIGNAL LINE CN2002 CN2004 M+9V VGND DETECT PY/Y/G C2200 0.039 VGND R2200 1K CB B D0/ST CB/PB/B TUNER C2100 0.039 PACK VGND R2100 1K CR R...
Page 99
SA-HT730GCP SCHEMATIC DIAGRAM-7 MAIN CIRCUIT :+B SIGNAL LINE :-B SIGNAL LINE :MAIN SIGNAL LINE R2068 R2069 R2005 R2052 R2054 R2051 R2049 R2047 R2042 Regu R2987 0 R2067 R2065 220 JOG A JOG A DSP LAT JOG LED SURR FC2 R2029 220...