Related Manuals for LG LMV1371TB
Summary of Contents for LG LMV1371TB
- Page 1 INSTALLATION INSTRUCTIONS MICROWAVE OVEN PLEASE READ AND SAVE THESE INSTALLATION INSTRUCTIONS. LMV1371TB LMV1371TW www.lg.com P/No.: MFL06210502...
-
Page 2: Your Safety First
YOUR SAFETY FIRST BEFORE YOU START Proper installation is the installer's responsibility! ● – Read the entire manual before you begin. The Model number label is located on the oven front. See Figure 1. Mounting plate is located on back side of microwave oven. See Figure 2. BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS: Model Number Label Mounting... - Page 3 YOUR SAFETY FIRST THIS APPLIANCE MUST BE GROUNDED! ● – If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug.
- Page 4 YOUR SAFETY FIRST MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. ● – Mount the oven against a flat, vertical wall, so that it is supported by the wall. – DO NOT mount the microwave oven to an island or peninsula cabinet. –...
-
Page 5: Parts, Tools, Materials
PARTS, TOOLS, MATERIALS THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector One power cord clamp and (for roof venting or wall venting installation) One dark-colored mounting screw Not Actual Size (to hold the power cord) Actual Size... - Page 6 PARTS, TOOLS, MATERIALS YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heavy material for covering the counter top. Clear Tape Stud Finder or Thin Nail (for taping the templates to the wall) Keyhole Saw (for the power cord hole) Saber Saw (for cutting vent holes for roof or wall vending)
-
Page 7: Step 1: Prepare The Electrical Connections
STEP 1: PREPARE THE ELECTRICAL CONNECTIONS W A R N I N G AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. NOTE: The outlet should be on a circuit dedicated to the Upper Cabinet... - Page 8 STEP 2: PREPARE THE VENTING SYSYTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 9, page 9. W A R N I N G -F I R E H A Z A R D THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways.
-
Page 9: Standard Fittings
STEP 2: PREPARE THE VENTING SYSYTEM STANDARD FITTINGS NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking. DUCT LENGTH The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not exceed the equivalent of 140 feet. -
Page 10: Roof-Vented Installation
STEP 3: PREPARE THE VENT MOTOR Your microwave oven is shipped with the blower assembled for room venting. If you want wall-venting or roof-vented installation, you must change the blower, as detailed below. W A R N I N G ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT. -
Page 11: Wall-Vented Installation
STEP 3: PREPARE THE VENT MOTOR WALL-VENTED INSTALLATION: Knockouts Use side cutters or tin snips. 1. Remove one motor mounting screw and two mount-all mounting screws. Take off the mount-all from the| oven. See Figure 14. 2. Carefully lift the vent motor of the microwave oven. 3. -
Page 12: Step 4: Prepare The Wall And Upper Cabinet For Installation
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION BEFORE YOU START 1. Remove any shipping materials and parts from inside the microwave oven. 2. Cover the counter top or cooktop with a thick, protective covering to protect it from damage and dirt. See Figure 16. - Page 13 STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION DRILL THE HOLES IN THE WALL AND UPPER CABINET. W A R N I N G BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL. Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock.
-
Page 14: Step 5: Install The Mounting Plate
STEP 5: INSTALL THE MOUNTING PLATE 1. Remove the template from upper cabinet. NOTE: If you are venting the oven through the wall, be sure you align the duct connector (included) on the rear of the mounting plate with the 3 "x10"... -
Page 15: Step 6: Attach The Oven To The Wall
STEP 6: ATTACH THE OVEN TO THE WALL W A R N I N G power cord You will need two people to lift this microwave. Failure to use more than one person could result in power cord hole personal injury. 1.