Table of Contents
Related Manuals for LG LT713 Series
Summary of Contents for LG LT713 Series
- Page 1 OWNER’S MANUAL Dome Camera Please read this manual carefully before operating your set and retain it for future reference. MODELS LT913 Series LT713 Series P/NO : MFL66281601 LT913-B.CNLDLLI_MFL66281601_ENG.indd 1 8/6/10 3:59 PM...
-
Page 2: Safety Information
Safety Information Safety Information REGULATORY INFORMATION: FCC Part 15 CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide RISK OF ELECTRIC SHOCK reasonable protection against harmful interference when DO NOT OPEN... - Page 3 Safety Information Warning: Do not install this equipment in a confined space LG Electronics hereby declares that this/ such as a bookcase or similar unit. these product(s) is/are in compliance Warning: Wiring methods shall be in accordance with the with the essential requirements and other National Electric Code, ANSI/NFPA 70.
-
Page 4: Important Safety Instructions
Safety Information IMPORTANT SAFETY 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been INSTRUCTIONS damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. - Page 5 Safety Information About Static Electricity Removal remove the dome cover and wipe all moist surfaces with a soft cloth. Before installing the camera, touch a metal case or other metallic parts with your hand to remove static electricity • Before operating, please check proper temperature, from your body.
-
Page 6: Table Of Contents
Contents Contents Connecting RS-485 device Connecting power source Protocol and baud rate settings Camera ID Setting Removing the Protection Tape Mounting the camera Surface mount (optional) Safety Information Ceiling mount (optional) Wall mount (optional) Pendant mount (Optional) IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Operation Preparation... - Page 7 Contents Auto Pan setting Privacy Mask setting Special setting OSD Settings User title setting ZOOM MAG setting FUNCTION setting DOME ID setting LANGUAGE Setting ALARM Setting Alarm In setting Alarm Out setting RESET Setting Information Initialization Factory reset Appendix Specifications LT913N/P series LT913NI/PI series LT713N/P series...
-
Page 8: Preparation
LT913 series: The optical zoom range is 1x to 37x. • Preset Tour LT713 series: The optical zoom range is 1x to 27x. Preset Tour is the function to go through all the • Digital Zoom registered camera monitoring positions (preset positions). -
Page 9: Accessories
Preparation Accessories When alarm inputs are supplied via the alarm input connector on the camera, the camera sends output For LT913NI/PI series signals via the alarm output connector on the camera. • Controls by General Controller This camera can be controlled by RS-485. Especially the RJ-45 Adapter cable camera has an excellent cost-saving effect because it can be controlled by the general RX point of contact... -
Page 10: Part Names And Functions
Preparation Part Names and Functions BNC connector cover cap Video output BNC connector LT913/713NI/PI series for Indoor Supplies analog video signal (composite) to the connected device. Data Port A (RJ-45) RS-485 data communication and input data port for alarm (relay) signal. Data Port B (RJ-45) Output data port for alarm (relay) signal. - Page 11 Preparation LT913/713N/P series for Outdoor BNC connector cover cap Video output BNC connector Supplies analog video signal (composite) to the connected device. Data Port A (RJ-45) RS-485 data communication and input data port for alarm (relay) signal. Data Port B (RJ-45) Output data port for alarm (relay) signal.
-
Page 12: Installation
Installation Installation Connections Precautions • The following steps of installation and connection work should be done by qualified service personnel or system installers and should conform to all local codes. • Before you install and connect the camera, check and prepare the required peripheral devices and cables. •... -
Page 13: Connecting Display Device
Installation Connecting Display device CAUTION The video signal connection between the camera and the monitor. Do not connect one alarm sensor to the several camera’s alarm input connector. Display device connection Alarm input connection Alarm device Alarm device Alarm device Alarm device Alarm device Alarm device... - Page 14 Installation Alarm Input function PORT A of the LT913/713NI/PI series This speed dome camera has a terminal that can sense the Description Color alarm signals. If the alarm sensor that has installed in a door, window, RS-485 + Red/White safe etc. sense a touch or shock, the alarm sensor send the RS-485 - Black/White alarm signal to the camera and the camera will observe the...
-
Page 15: Alarm Output Connections
Installation ALARM output connections ALARM OUT [NC2] Blue Connect the alarm device to the alarm output data port. Brown Alarm signal output at an event occurrence. You can set the Alarm Output to the normal open or normal close mode. 1. -
Page 16: Connecting Lkd1000 Controller
Installation RJ-45 Adapter cable PORT A Connecting LKD1000 controller RS-485 connection 1. Connect the RJ-45 Adapter cable to the PORT A (RJ-45) cable of the camera. 2. Connect the LKD1000 controller to the RJ-45 Adapter cable. (Refer to the manuals of the LKD1000 controller for more details.). -
Page 17: Connecting Power Source
Pelco D Pelco P OSD Set NOTE If you are not using the controller with LG Multix protocol, there may be some limitation of function control. 5. Assemble the dome cover and the camera assembly cover in the reverse order. -
Page 18: Camera Id Setting
Installation Camera ID Setting OFF OFF OFF OFF OFF The camera’s ID is set to “0” as factory default. If you use OFF OFF OFF two or more cameras simultaneously, change the ID of the OFF OFF OFF cameras. OFF OFF OFF Set the camera ID setting referring to the pictures and the table on the below. - Page 19 Installation OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF...
- Page 20 Installation OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF...
-
Page 21: Removing The Protection Tape
Installation Removing the Protection Tape OFF OFF OFF OFF OFF You should remove the protection tape before installing OFF OFF OFF OFF the camera. Remove the protection tape carefully. OFF OFF OFF OFF OFF OFF For LT913/713N/P series models. OFF OFF OFF OFF 1. -
Page 22: Mounting The Camera
Installation Mounting the camera 2. Install the surface mounting bracket on the ceiling. You can mount the camera on the ceiling or wall. Surface mount (optional) Follow the instructions below to surface mount the camera. CAUTION The building structure must be able to support 8 kg. 1. -
Page 23: Ceiling Mount (Optional)
Installation Ceiling mount (optional) 4. Tighten the locking screw. Follow the instructions below to mount the camera on the ceiling. CAUTION The building structure must be able to support 8 kg. 1. Make a hole through the ceiling as shown below. Ø... - Page 24 Installation 3. Install the ceiling mounting bracket on the ceiling. Face 5. Pass the connection cable through the inner side of the front of the ceiling mounting bracket toward the the ceiling. Connect the cables to the cable jacks of the area of interest.
-
Page 25: Wall Mount (Optional)
Installation Wall mount (optional) 7. Tighten the locking screw. Install the camera by the following order. 1. Connect the safety cable to the wall mount assembly. 8. Connect the cables to the cable jacks of the camera body. After installing the camera, you should arrange the cables using the outlet box to protect the cables. - Page 26 Installation 2. Drill a hole on the wall where you want to install the 5. Attach the camera to the camera assembly bracket by pipe. Pass the connection cable through the wall following step a and b . Align the locking point of mount assembly so that they hang down.
-
Page 27: Pendant Mount (Optional)
Installation Pendant mount (Optional) 7. Assemble the camera cover as shown below. Install the camera by the following order. 1. Connect the safety cable to the pendant mount assembly. Red Stripe LT913-B.CNLDLLI_MFL66281601_ENG.indd 27 8/6/10 4:00 PM... - Page 28 Installation 2. Drill a hole on the wall where you want to install the 3. Install the pendant mount assembly. pipe. Pass the connection cable through the pendant mount assembly so that they hang down. 4. Connect the connection cable and the safety cable to the camera body.
- Page 29 Installation 5. Attach the camera to the camera assembly bracket by 7. Assemble the camera cover as shown below. following step a and b . Align the locking point of the wall mount assembly and the camera. 6. Tighten the locking screw. LT913-B.CNLDLLI_MFL66281601_ENG.indd 29 8/6/10 4:00 PM...
-
Page 30: Operation
3rd level Contents AUTO/MANUAL/ONE PUSH/ FOCUS MODE ZOOM TRIG FOCUS LT913 Series : 50 CM, 1.8 M, 3 M, 6 M FOCUS DIST LT713 Series : 50 CM, 1 M, 3 M, 5 M RETURN IRIS AUTO/MANUAL OFF/LOW/MIDDLE/HIGH WDR/BLC OFF/WDR/BLC/HSBLC BRIGHTNESS... - Page 31 Operation D/N LEVEL LOW/MIDDLE/HIGH AUTO DWELL TIME 5,10,15,30,60 SEC DAY/NIGHT RETURN NIGHT 3D-DNR MIDDLE HIGH COLOR -20 to 20 COLOR SHARPNESS 0 to 68 RETURN NAME OFF/ON SPEED 1 to 127 DWELL TIME 1 to 255 IRIS AUTO, 20, 40, 60, 80, 100 % OFF/ LOW WDR/ MID.
- Page 32 RETURN RETURN TIME SPECIAL (1 MIN to 100 MIN) AUTO RETURN TILT LIMIT ON/OFF PROTOCOL LG MULTIX/ PELCO D/ PELCO P 2 400/ 4 800/ 19 200/ 38 400/ BAUDRATE 9 600 BPS COMMUNICATION SAVE & EXIT RETURN LT913-B.CNLDLLI_MFL66281601_ENG.indd 32...
- Page 33 Operation RETURN USER TITLE ON/OFF ZOOM MAG ON/OFF OSD SET FUNCTION ON/OFF DOME ID ON/OFF RETURN The option depends LANGUAGE on the model. NORMAL OPEN/CLOSE ALARM IN1 to ALARM IN4 PRESET 0 to 127 ALARM IN1 to DWELL TIME 3 to 255 ALARM IN4 RETURN ALARM SET...
-
Page 34: Menu Navigation
We use the LKD1000 controller in this manual to explain PRESET /CAM1 the features of the LG Dome camera because of the LKD1000’s ability to control all of the LG Dome camera’s advanced features. (For detailed controller instructions, refer to the LKD1000 Controller Manual.) -
Page 35: Camera Menu Settings
Operation Camera menu settings Focus Distance setting Selects the minimum shooting distance for the focus. Select [FOCUS DIST] option on the [FOCUS] menu, then select a focus distance value. Focus setting Exposure settings The camera adjusts the focus automatically by sensing the center of the picture. -
Page 36: White Balance Setting
Operation WDR/BLC setting SHUTTER (Shutter Speed) setting Use WDR/BLC option to set the options for BLC or WDR Select the desired shutter speed for camera exposure. You camera. can change the shutter speed to higher speed to capture fast-moving subjects, though the image becomes darker. 1. -
Page 37: Day/Night Setting
Operation temperature objects, such as a blue sky or D/N LEVEL: Use [Near] or [Far] button to select a sunset. level. When the scene is dim. DWELL TIME: Use [Near] or [Far] button to select a dwell time. • AUTO: In this mode, the color temperature range for the proper white balance is approximately NOTE 2 700 K to 5 400 K. -
Page 38: Color Setting
Operation PAN/TILT Settings Color setting You can switch the displayed picture to grayscale or color. Preset setting Preset position is the function to register camera monitoring positions (preset positions) associated with position numbers. By entering the position numbers, you can move cameras to the preset positions. 1. -
Page 39: Group Tour Setting
Operation To clear the preset position • CLR: If you enter the wrong code, select [CLR] then press [Open] or [Close] to delete. All letters You can clear a memorized preset position. will be erased at once. 1. Select [CLEAR PRESET] option on the [PRESET] menu. •... -
Page 40: Pattern Setting
Operation Pattern setting To set the group 1. Select [SET GROUP] option on the [GROUP TOUR] You can activate the camera in a repeating pattern. The menu. pattern is programmed by recording your manual pan, tilt, and zoom operations. The camera stores the movements 2. -
Page 41: Auto Pan Setting
Operation Auto Pan setting To play the auto pan You can play the camera with auto pan function. By selecting the Auto Pan number, the camera pans automatically. 1. Select [RUN] option on the [AUTO PAN] menu. 2. You can stop the Auto pan function by moving the joystick or pressing any button. -
Page 42: Special Setting
Operation Special setting 5. Select the mask zone using the joystick and then press [Open] or [Close] button to save it. 6. Use [Near] or [Far] button to set up the [ON] or [OFF] on the [MASK STATE] option. If you already registered the mask zone and set to ON, the mask zone box appears on the monitor. - Page 43 Operation Home position The home position is the camera’s basic position. NOTE The camera returns to this position whenever you want. If you set [AUTO RETURN] to [ON], the [HOME POSITION] Use the following procedure to make the home position. option is set to [OFF] automatically and you can not use 1.
-
Page 44: Osd Settings
Operation OSD Settings • CLR: If you enter the wrong code, select [CLR] then press [Open] or [Close]. All letters will be erased at once. • POS: Move the USER TITLE position on the screen using the [Near] or [Far] buttons. •... -
Page 45: Dome Id Setting
Operation ALARM Setting DOME ID setting Displays or removes the Camera ID OSD on the screen. This camera has a terminal that can sense the alarm signals. The camera can be programmed to go to a preset with a signal from any connected alarm device. 1. -
Page 46: Alarm Out Setting
Operation Alarm Out setting Initialization 1. Select one of the alarm out options on the [ALARM You can initialize the camera settings. SET] menu. 1. Select [INITIALIZATION] option on the [RESET] menu. 2. Use [Near] or [Far] button to set it [ON]. 2. -
Page 47: Appendix
Appendix Appendix Specifications LT913N/P series Model LT913N LT913P Signal System NTSC (High Resolution) PAL (High Resolution) Pick-Up Device 4.5 mm EX-view HAD CCD Total Pixels No 410 000 Pixels 470 000 Pixels Horizontal Resolution More Than 540 TV Lines Lens x37 Zoom ( F1.5 (Wide Angle), F4.1 (Tele)), f = 3.5 mm to 129 mm S/N Ratio More Than 50 dB (AGC Off ) -
Page 48: Lt913Ni/Pi Series
Appendix 0 º to 360 º (Endless) , Maximum 400 º /second Panning Range (Speed) 0 º to 180 º , Maximum 400 º /second Tilting Range (Speed) Privacy Zone 8 area active programmable zone Preset/ID 128 position / 256 Auto Panning 2 to 8 points Pattern... - Page 49 Appendix Alarm Input 4 Channel Alarm Output 2 Channel Video Output Composite Output 1 Vp-p ( 75 Ω Terminated) Electronic Shutter 1/60 to 1/90 000 second 1/50 to 1/90 000 second Iris Control Auto / Manual Wide Dynamic Range Dual Shutter Control (62 dB) 0 º...
-
Page 50: Lt713N/P Series
Appendix LT713N/P series Model LT713N LT713P Signal System NTSC (High Resolution) PAL (High Resolution) Pick-Up Device 4.5 mm EX-view HAD CCD Total Pixels No 410 000 Pixels 470 000 Pixels Horizontal Resolution More than 540 TV Lines Lens x27 Zoom ( F1.5 (Wide Angle), F3.8 (Tele Photo)), f = 3.25 mm to 88 mm S/N Ratio More Than 50 dB (AGC Off ) Day &... -
Page 51: Lt713Ni/Pi Series
Appendix LT713NI/PI series Model LT713NI LT713PI Signal System NTSC (High Resolution) PAL (High Resolution) Pick-Up Device 4.5 mm EX-view HAD CCD Total Pixels No 410 000 Pixels 470 000 Pixels Horizontal Resolution More than 540 TV Lines Lens x27 Zoom ( F1.5 (Wide Angle), F3.8 (Tele Photo)), f = 3.25 mm to 88 mm S/N Ratio More Than 50 dB (AGC Off ) Day &... - Page 52 LT913-B.CNLDLLI_MFL66281601_ENG.indd 52 8/6/10 4:00 PM...