DeWalt DWS774 Manual
Hide thumbs
Also See for DWS774:
- Instructions manual (33 pages) ,
- Original instructions manual (28 pages) ,
- Original instructions manual (121 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for DeWalt DWS774
Summary of Contents for DeWalt DWS774
- Page 1 DWS773 DWS774 Final Page size: A5 (172mm x 240mm)
- Page 2 Dansk (oversat fra original brugsvejledning) Deutsch (übersetzt von den originalanweisungen) English (original instructions) Español (traducido de las instrucciones originales) Français (traduction de la notice d’instructions originale) Italiano (tradotto dalle istruzioni originali) Nederlands (vertaald vanuit de originele instructies) Norsk (oversatt fra de originale instruksjonene) Português (traduzido das instruções originais) Suomi (käännetty alkuperäisestä...
- Page 3 DWS773 DWS774 250 – 300 Lux...
- Page 4 6 mm XXXX-XX-XX DWS773 DWS774...
- Page 5 >15 mm > 8 mm...
- Page 8 0° 0°...
- Page 9 α = 90° α = 90° α α ≠ 90° α = ⁄ 90° α ≠ 90° α = 90° α...
- Page 10 α ≠ 90° α ≠ 90° α ≠ 90° α ≠ 90°...
- Page 11 α α = 90°...
- Page 12 α = 45° α = 48° α = 45°...
- Page 14 >10 cm DWS774...
- Page 16 45°...
- Page 17 α ≠ 90°...
- Page 18 α β γ α γ β...
- Page 19 α...
- Page 20 β γ γ β...
-
Page 22: Vibration Emission
EN 62841-3-9:2015. These products also comply with Directive 2014/30/ left 48° 48° EU and 2011/65/EC. Mitre positions, max. right 48° 48° For more information, please contact DEWALT at the following address Bevel position, max. left 48° 48° or refer to the back of the manual. bevel 45° 45°... - Page 23 DWS774: A failure of XPS, has no effect on the intended operation. d ) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
- Page 24 4) Power tool use and care the saw head down and push the saw through the workpiece. Cutting on the pull stroke is likely to cause the saw blade to climb a ) Do not force the power tool. Use the correct power tool for on top of the workpiece and violently throw the blade assembly your application.
-
Page 25: Personal Protective Equipment
Personal Protective Equipment plug from the power source and/or remove the battery pack. Then work to free the jammed material. Continued sawing with a Loose clothes, jewellery, noise and similar hazards may present a danger jammed workpiece could cause loss of control or damage to the to persons. - Page 26 In case of cord or plug replacement the tool must only be repaired by an authorized service agent or by qualified electrician. The following cords are mandatory: Keep away from children DWS773, DWS774: 230V H05RN-F, 2 x 1.0 mm2 DWS773, DWS774: 115V H05RR-F, 2 x 1.5 mm2 Do not use the tool in damp or wet conditions Mains plug replacement (UK &...
-
Page 27: Dust Extraction
Adjustments and Replacements • As you move the saw arm left and right, follow it and stand slightly to the side of the saw blade. Cutting • Always let the blade come to a full stop before raising the arm. If small fibres of wood still split out at the rear of the workpiece, stick a piece of masking tape on the wood where the cut will be The Mitre Saw was accurately adjusted at the factory. - Page 28 • The guide grooves can become clogged with sawdust. Use suitable dust extraction or some low pressure air to clear the guide grooves. • Disconnect the machine from the mains before carrying out any maintenance work or when changing the blade. •...
- Page 32 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT Tel: 70 20 15 10 www.dewalt.dk...