Table of Contents
Advertisement
Quick Links
Specification
Type
Speaker unit(s)
Full range
Full range
Input power (IEC)
Output sound pressure
Cross over frequency
Frequency range
Dimensions (W x H x D)
CONTENTS
2 way, 2 speaker system (Bass reflex)
Impedance 6 Ω
6.5 cm (2-1/2") cone type
6.5 cm (2-1/2") cone type
250* W (Max)
82 dB/W (1.0 m)
80 Hz - 25 kHz (-16 dB)
96 Hz - 22 kHz (-10 dB)
270 x 94 x 95 mm
SB-HC950P
Colour
(K)... Black Type
Mass
Notes :
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
5 kHz
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
* : Rating with low-cut filter equipped amplifier.
Page
2
2.4. Disassembly of Woofer 2
2
2
3
3
4
5
© 2007 Matsushita Electric Industrial Co. Ltd.. All
rights
distribution is a violation of law.
ORDER NO. MD0702013CE
Speaker System
(10-5/8" x 3-11/16" x 3-3/4")
1.3 kg (2.9 lbs)
reserved.
Unauthorized
copying
A6
Page
5
6
7
10
11
11
12
and
Advertisement
Table of Contents
Related Manuals for Panasonic SB-HC950P
Summary of Contents for Panasonic SB-HC950P
-
Page 1: Table Of Contents
ORDER NO. MD0702013CE Speaker System SB-HC950P Colour (K)... Black Type Specification Type 2 way, 2 speaker system (Bass reflex) (10-5/8” x 3-11/16” x 3-3/4”) Impedance 6 Ω Speaker unit(s) Mass 1.3 kg (2.9 lbs) Full range 6.5 cm (2-1/2”) cone type Full range 6.5 cm (2-1/2”) cone type... -
Page 2: System Combination
1.1. System Breakdown Note : The diagrams below show the breakdown for speaker combinations used in main unit systems. SB-PT950P-K consists of SB-HF950P-K (x2), SB-HS950P-K (x2), SB-HC950P-K (x1) SB-PT1050P-K consists of SB-HF1050P-K (x2), SB-HS1050P-K (x2), SB-HC950P-K (x1) 1.2. Packaging Information... -
Page 3: Assembling And Disassembling
SB-HC950P 2 Assembling and Disassembling “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. -
Page 4: Disassembly Of Rear Cabinet
SB-HC950P 2.2. Disassembly of Rear cabinet Step 1: Remove 6 screws. Step 5: Detach the blue (+) and gray (-) wires. Step 2: Upset the speaker unit as shown above. Step 3: Insert a steel rule into the top conner of the rear cabinet as arrow shown. -
Page 5: Disassembly Of Woofer
SB-HC950P 2.3. Disassembly of Woofer 1 2.4. Disassembly of Woofer 2 Follow (step 1) to (step 4) in item 2.2. Follow (step 1) to (step 4) in item 2.2. Step 1: Detach the black (+) and gray (-) wires. Step 1: Detach the blue (+) and blue (-) wires. -
Page 6: Disassembly Of Terminal Jack
SB-HC950P 2.5. Disassembly of Terminal jack Follow (step 1) to (step 5) in item 2.2. Step 1: Remove 1 screw from the terminal jack. Step 2: Remove terminal jack as arrow shown. -
Page 7: Connection Of The Speaker Cables
SB-HC950P 3 Connection of the Speaker Cables · Be sure to connect speaker cables before connecting the AC power supply cord. · The load impedance of any speaker used with this unit must be 6 Ω. · Be sure to connect the cable from the right speaker to the right terminal and the cable from the left speaker to the left terminal. - Page 8 SB-HC950P Positioning the speakers...
- Page 9 SB-HC950P Note on speaker use · Use only supplied speakers. Using other speakers can damage the unit, and sound quality will be negatively affected. · You can damage your speakers and shorten their useful life if you play sound at high levels over extended periods.
-
Page 10: Connection Of The Wiring Diagram
SB-HC950P 4 Connection of the Wiring Diagram... -
Page 11: Exploded View
SB-HC950P 5 Exploded view 5.1. Cabinet Parts Location... -
Page 12: Replacement Parts List
SB-HC950P 6 Replacement Parts List Notes : · Important safety notice : When replacing any of these components, be sure to use only manufacturer’s specified parts shown in the parts list. · [M] markings in the Remarks columns indicates parts supplied by PAVCSG.