Table of Contents
Advertisement
Available languages
Available languages
English
Joining Saw Head Module to Handle Module
(Fig. I–L)
WARNING: Sharp moving blade. To prevent accidental
operation, insure that battery is disconnected from the
handle and that the protective scabbard is in place on the
chain before performing the following operations. Failure
to do this could result in serious personal injury.
The three assembliess which make up the pole saw are keyed
to insure correct assembly. If an assembly does not smoothly
attach to another do not force fit.
Combining the handle assembly
assembly
creates a pole saw that is approximately 1.8 m in
3
length as shown in Fig. I.
To attach the handle assembly to the saw head assembly:
1. Align the groove
22
on the outside of the coupling end of
the handle assembly
1
of the coupling end of the saw head assembly
Fig. J. Push the two sections completely together. Refer to
Fig. K.
2. Slide the threaded sleeve
down as far as possible and rotate the sleeve clockwise
until it stops and completely covers the threads as shown
in Fig. L.
WARNING: Always check to make sure that the sleeve
is completely threaded on and that the red threads are
no longer visible. Not threading the sleeve completely
on could result in the assemblys becoming disconnected
creating a hazardous condition. Periodically check the
connections to insure that no red threads are visible.
Joining Center Extension to Saw Head
Module and Handle Module (Fig. A, M)
Adding the center extension
saw head assembly
creates a pole saw that is approximately
3
2.7 m in length as shown in Fig. M.
Refer to to Joining Saw Head Module to Handle Module for
directions on how to attach the middle assembly to the handle
assembly and saw head assembly.
WARNING: Always check to make sure that the sleeve
is completely threaded on and that the red threads are
no longer visible. Not threading the sleeve completely
on could result in the assemblys becoming disconnected
creating a hazardous condition. Periodically check the
connections to insure that no red threads are visible.
DISASSEMBLY
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
16
to the saw head
1
with the tongue
23
on the inside
. Refer to
3
9
on the saw head assembly
to the handle assembly
2
Detaching Saw Head Module (Fig. N)
WARNING: Sharp moving blade. To prevent accidental
operation, insure that battery is disconnected from the
handle and that the protective scabbard is in place on the
chain before performing the following operations. Failure
to do this could result in serious personal injury.
When detaching the assemblies, whether it is in the two
assembly or three assembly mode, always detach the saw head
assembly
3
first. To do this, rest the handle assembly
ground and grasp the center of the saw head assembly with
one hand as shown in Fig. N. Use your other hand to loosen the
threaded sleeve and then pull the two halves apart. Repeat this
process if the center extension was attached.
Attaching and Adjusting the Shoulder Strap
(Fig. O)
This pole saw comes with an adjustable shoulder strap.
1. Snap the shoulder strap latch
as shown in Fig.O.
2. Adjust the strap so it fits securely over your shoulder.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. P)
WARNING: To reduce the risk of serious personal injury,
and
1
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
and one hand on the foam gripper
Operating the Pole Saw (Fig. A)
WARNING: Read and understand all instructions. Failure
to follow all instructions listed below may result in electric
shock, fire and/or serious personal injury.
CAUTION: Always reduce the tension off the chain again
after finishing work. The chain contracts as it cools down.
If it is not slackened off, it can damage the pole saw.
iMPORTAnT: Never operate a pole saw that is damaged or
improperly adjusted or that is not completely and securely
assembled. Be sure that the saw chain
the trigger switch is released. Never adjust the guide bar
saw chain when the motor is operating or the battery is attached.
1
on the
onto the strap mount
28
19
.
7
stops moving when
14
or
13
29
Advertisement
Table of Contents
