Therefore, the following checks should be performed for the continued protection of the customer and servicetechnician. PDP-503CMX...
Page 3
PRODUCT SAFETY NOTICE With the AC plug removed from an AC power source, place a Many electrical and mechanical parts in PIONEER set have jumper across the two plug prongs. Turn the AC power switch on. special safety related characteristics. These are often not evident...
Page 4
Assy Front SCAN (B) Assy X CONNECTOR (A) Assy X DRIVE Assy X CONNECTOR (B) Assy SW POWER SUPPLY Module Power Switch (S1) AC Inlet with Filter Power Cord Fig.1 Charged Section and High Voltage Generating Point (Rear View) PDP-503CMX...
Page 5
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. PDP-503CMX...
7.1 DIAGNOSIS ............................120 7.1.1 CONFIGURATION OF THE PC BOARD ..................120 7.1.2 DIAGNOSIS FOR SHUTDOWN AND POWER-DOWN BY LED............. 121 7.1.3 AUTOMATIC BACKUP OF DIGITAL VIDEO ASSY DATA..............131 7.1.4 DISASSEMBLY..........................133 7.2 IC INFORMATION..........................137 8. PANEL FACILITIES ............................163 PDP-503CMX...
Number of pixels ..........1280 x 768 Remote control unit holder ..........1 Power supply ..AC 100 - 120 V, 50/60 Hz (PDP-503CMX) AA (R6) batteries ............2 Power supply ..AC 100 - 240 V, 50/60 Hz (PDP-503MXE) Cleaning cloth ...............
Page 8
Accessories Power Cord (ADG1208) Cleaning Cloth (for wiping front panel) Display Stand (×2) (AMR3264) (AED1208) PDP-503CMX Only Binder Assy (AEC1758) Remote Control Unit Washer (×2) (WB80FZB) Hex Hole Bolts (×2) (AXD1459) (SMZ80H400FZB) Speed Clamp (×2) Remote Control Unit Holder (AMR3268) Bead Bands (×2)
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING 40 41 PDP-503CMX Only PDP-503MXE Only PDP-503CMX...
Page 11
See Contrast table (2) Accessory Assy See Contrast table (2) Caution Sheet See Contrast table (2) (2) CONTRAST TABLE PDP-503CMX/LUCB and PDP-503MXE/YVLDK are constructed the same except for the following : PDP-503CMX/ PDP-503MXE/ Mark No. Symbol and Description LUCB YVLDK...
CLAMP A Assy AWZ6738 CLAMP B Assy AWZ6739 Screw ABA1301 CLAMP C Assy AWZ6740 V Cushion AED1205 CLAMP D Assy AWZ6741 Service Panel Assy AWU1068 Wire Saddle AEC1904 Circuit Board Spacer AEC1872 Circuit Board Spacer AEC1873 NSP 9 PCB Spacer AEC1121 PDP-503CMX...
Page 13
PW : Common use of public use and module ∗ In case of this unit, all the parts carved a seal of character removes it. Service Panel Assy (AWU1068) Wire Saddle Circuit Board Spacer Circuit Board Spacer (AEC1878) (AEC1872) (AEC1872) (There is marking of "P" nearby.) PDP-503CMX...
AEC1902 NSP 3 Front Chassis H ANA1683 Seet C AEC1927 Sub Frame L ANG2455 NSP 15 Front Chassis HU ANA1697 Sub Frame R ANG2456 FPC Cushion AEB1370 NSP 7 Front Chassis V ANA1661 Screw AMZ30P060FZK Screw ABA1294 Screw BMZ30P060FMC PDP-503CMX...
Display Label See Contrast table (2) Serial Label AAX2609 NSP 10 Panel Holder ANG2508 (2) CONTRAST TABLE PDP-503CMX/LUCB and PDP-503MXE/YVLDK are constructed the same except for the following : PDP-503CMX/ PDP-503MXE/ Mark No. Symbol and Description LUCB YVLDK 19 Display Label...
Terminal Display Label R AAX2931 Label (GREEN) AAX2955 Bolt Caution Label AAX2928 (2) CONTRAST TABLE PDP-503CMX/LUCB and PDP-503MXE/YVLDK are constructed the same except for the following : PDP-503MXE/ PDP-503CMX/ Mark No. Symbol and Description LUCB YVLDK 1 Name Label Gray...
Page 47
Clamp Mode : AUTO Clamp Mode : AUTO Clamp Mode : AUTO Clamp Mode : AUTO Color Mode : COLOR MODE 1 Color Mode : COLOR MODE 1 Color Mode : COLOR MODE 1 Color Mode : COLOR MODE 1 PDP-503CMX...
Page 48
K5315 (HD_SEL) and k 5317 (HD _ 30) synchronize with K5316 (VD_SEL). K5316 (VD_SEL) K5317 (HD_30) K5314 (DE_SEL) K5315 (HD_SEL) Magnified K5316 (VD_SEL) section of No. 32. Frequency of 2 times of K5314 K5316 (VD_SEL) (DE_SEL), K5315 (HD_SEL) and K5317 (HD_30) in the 1125i indication. K5316 (VD_SEL) K5317 (HD_30) PDP-503CMX...
• Execute Final Setup signal input MUTING key (AA49) Double audio (AA1E) OFFSET mode • Adjustment of the signal input. MUTING key (AA49) VIDEO OPTION mode SCREEN SIZE (AAD3-AF3C) MUTING key (AA49) INITIALIZE mode Full auto zoom (AAD3-AF36) or P. ZOOM (AAD3-AF22) PDP-503CMX...
Page 66
• AXD1459 (PDP-503CMX) POWER POWER MENU SCREEN DISPLAY CALL SIZE SCREEN SIZE FULL AUTO FULL AUTO ZOOM ZOOM DISPLAY CALL SURROUND MUTE MODE MUTE SOUND AUDIO VOLUME SOUND MENU VOLUME AV MEMORY SURROUND MODE AV SELECT AUDIO • AXD1432 • AXD1673...
Page 67
• While there is no input, The partial setting, or while incompatible PC signals are input, settings that are not dependent on the signal mode can be performed. (For the MASK setting, see "MASK 1," and "MASK 2.") The setting items that are dependent on the input signal mode are grayed on the display and cannot be changed. PDP-503CMX...
R SIDE MASK LEV R SIDE MASK LEV VOP-M LEV-1 0 to 255 IC30 G SIDE MASK LEV G SIDE MASK LEV VOP-M LEV-2 0 to 255 B SIDE MASK LEV B SIDE MASK LEV VOP-M LEV-3 0 to 255 PDP-503CMX...
Page 69
VIDEO OPTION), and add the OFFSET value of the selected setting. The addition of the COLOR TEMP OFFSET value is not needed in Integrator mode or in Service Factory mode (except for COLOR TEMP adjustment mode,) because the unit operates with the COLOR TEMP 3 settings. PDP-503CMX...
: OFFSET value (adjustment value) * Adjustment value is REFERENCE value + OFFSET value. 3. When VIDEO OPTION is selected : No display When INITIALIZE is selected : Selected setting. (No display for an item having the lower layer.) PDP-503CMX...
Page 71
• When this mode is entered, the VERSION display (the function called by pressing the "1" key) is displayed first. • When any of the above keys are pressed, the corresponding operation is executed. Note: The VERSION display is the default display for Service Factory mode. PDP-503CMX...
Page 72
Up to eight power-downs are displayed. If the number of power-downs becomes more than 8, the latest data are added, and the oldest data are cleared. Display details at PD INFORMATION Display PD Point Display PD Point X-DRV X-DRIVE ADRES ADDRESS junction X-DDC X-DC/DC CONVERTER ADR-K ADDRESS resonance Y-DRV Y-DRIVE POWER Power supply Y-DDC Y-DC/DC CONVERTER DC-DC DC/DC CONVERTER (DIGITAL) PDP-503CMX...
Page 74
• When a slot is not inserted, or when a slot manufactured by other vendor is inserted, the SLOT item cannot be selected. (The display is not skipped during item selection.) • Items that cannot be selected are grayed on the display. PDP-503CMX...
Page 75
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "____," and the item indication is grayed. PDP-503CMX...
Page 76
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "____," and the item indication is grayed. PDP-503CMX...
Page 77
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "____," and the item indication is grayed. PDP-503CMX...
Page 78
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "____," and the item indication is grayed. PDP-503CMX...
Page 79
• When a slot is not inserted, or when a slot manufactured by other vendor is inserted, the SLOT item cannot be selected. (The display is not skipped during item selection.) • Items that cannot be selected are grayed on the display. • Selection of each item is impossible when there is no input signal. PDP-503CMX...
Page 80
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "___(___)," and the item indication is grayed. PDP-503CMX...
Page 81
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "___(___)," and the item indication is grayed. PDP-503CMX...
Page 82
• When the input signal mode is not identified, the adjustment value is displayed with "___(___)," and the item indication is grayed. • As the items X-SUS-B, X-SUS-G, Y-SUS-B, Y-SUS-G, V-SUS, and V-OFFSET do not have OFFSET adjustment values, making settings is not allowed. These items are grayed, and the adjustment values are displayed with "___(___)." PDP-503CMX...
Page 83
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • When the input signal mode is not identified, the adjustment value is displayed with "___(___)," and the item indication is grayed. PDP-503CMX...
Page 84
RANGE CHECK AA59 AV SELECT REFERENCE Shifting to various AA43 AV MEMORY adjustment / setting AA1E OFFSET screen AAD3-AF3C SCREEN SIZE VIDEO OPTION AAD3-AF36 FULL AUTO ZOOM INITIALIZE AAD3-AF22 P.ZOOM Shifting to next adjustment AA49 MUTING INITIALIZE / setting screen PDP-503CMX...
Page 85
• COLOR TEMP setting during COLOR TEMP adjustment When Service Factory mode is entered, the setting for COLOR TEMP becomes MIDDLE regardless of the user's setting. During COLOR TEMP adjustment, the unit operates in the selected COLOR TEMP mode. PDP-503CMX...
Page 86
• When this mode is entered, the R SIDE MASK LEVEL display (the function called by pressing the "1" key) is displayed first. • When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. PDP-503CMX...
Page 87
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • During COLOR MODE adjustment, the setting becomes COLOR MODE 2, and the adjusted value will be stored in memory, but the color mode setting will not be stored after adjustment is completed. PDP-503CMX...
Page 88
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. • During COLOR TEMP adjustment, the unit operates with the selected COLOR TEMP setting, and the adjusted value will be stored in memory, but the COLOR TEMP setting will return to MIDDLE after adjustment is completed. PDP-503CMX...
Page 89
RANGE CHECK AA59 AV SELECT REFERENCE Shifting to various AA43 AV MEMORY adjustment / setting AA1E OFFSET screen AAD3-AF3C SCREEN SIZE VIDEO OPTION AAD3-AF36 FULL AUTO ZOOM INITIALIZE AAD3-AF22 P.ZOOM Shifting to next adjustment AA49 MUTING INFORMATION / setting screen PDP-503CMX...
Page 90
SET : To register the setting and shift to the confirmation screen for setting changes. U L S S E T N OW D A T A : 1 2 3 4 5 S E T D A T A : 0 9 7 0 0 PDP-503CMX...
Page 91
• To release the mask setting, use "M00" of RS-232C Factory Adjustment mode or "MASK OFF" of Service Factory menu. (The mask setting cannot be released with FULL MASK OFF of the Integrator menu or "FMN" of the RS-232C Factory Adjustment mode.) PDP-503CMX...
Page 92
Note: If PICTURE DEFAULT is executed: 1 All the PICTURE items set on the user menu are reset. 2 The values for PICTURE, WHITE BAL, and SIDE MASK LEVEL of the Integrator menu will become those of current adjustment values of Service Factory mode. PDP-503CMX...
Page 93
For each function that can be controlled by the PC HDTV MODE 1035i Common to all input functions COMPONENT1 750p/1125i/1125p VIDEO INPUT COMPONENT2 525i/525p/625i/625p SUB VOLUME For each input function Common to all units BAUD RATE 4800BPS (Setting/Timer time/Mask time/mask color) TIMER OFF/1/0.0/WHT Common to all input functions PDP-503CMX...
Page 94
Common to all units − − ID NO SET SLOT INPUT VIDEO (RGB) Factory Setting Item INTE MODE UNLOCK MASK1/2 setting Common to all units ACL SW COLOR DET NO CARE RS-232C Setting Item VIDEO MUTE Common to all units 100% display PDP-503CMX...
Page 95
• When any of the above keys is pressed, the current adjustment value is stored in memory, then the corresponding operation will be executed. Note: During MASK setting, an OSD is not displayed. If another operation is selected, an OSD is displayed for 2 seconds after the MASK signal output is stopped, then the selected FULL MASK display will be displayed again. PDP-503CMX...
Page 96
RANGE CHECK AA59 AV SELECT REFERENCE Shifting to various adjustment / AA43 AV MEMORY setting screen AA1E OFFSET AAD3-AF3C SCREEN SIZE VIDEO OPTION AAD3-AF36 FULL AUTO ZOOM INITIALIZE AAD3-AF22 P.ZOOM AA49 MUTING Shifting to next adjustment / setting screen INFORMATION PDP-503CMX...
2. Color difference and TINT adjustment When replaced No adjustment required. DIGITAL VIDEO Assy SW POWER SUPPLY Module Y DRIVE Assy X DRIVE Assy RGB Assy Video Card (PDA-5002) Fig. 1 Configuration of the PC Board (rear side view) PDP-503CMX...
PSUS (=GNDH) is a floating GND and its electric potential is different from that of chassis (Y DRIVE Assy) GND. Be sure not to short-circuit PSUS (=GNDH) and another GND, because that may damage the unit. Note : Be sure to measure between specified test points. PDP-503CMX...
Page 102
Side mask color / Level Adjustment SIDE MASK LEV. Set the indicated value with the keys on the remote control unit (1, 2 and 3 keys). R SIDE LEVEL : key 1 G SIDE LEVEL : key 2 B SIDE LEVEL : key 3 PDP-503CMX...
Page 103
Green signal measured in step 9. Tolerance: ± 0.05V OFFSET mode: Select RGB 1 mode with the top and bottom keys. AD B HIGH : "8" key Adjust with the right and left keys. PDP-503CMX...
Page 104
Green signal measured in step 9. Tolerance: ± 0.05V OFFSET mode: Select RGB 1 mode with the top and bottom keys. AD R HIGH : "6" key Adjust with the right and left keys. PDP-503CMX...
Page 105
TINT : "4" key Reference: Adjustment values when using the Minolta color-difference meter NTSC 20% window-step signal (-3dB) White Balance 80% window-step signal (-3dB) 66.2 − Flesh Window chroma signal Color − PDP-503CMX...
TxD outputs of data on various SETUP settings − − − − GET ADJUST SLOT TxD outputs of data of picture quality setting of SLOT − − − − GET ADJUST RGB TxD outputs of data of picture quality adjustment (RGB 1) PDP-503CMX...
Page 109
Top and bottom reversing display − − MIRROR MODE XY Top/bottom and right/left reversing display − − VIDEO MUTE NO To turn the video mute of IC30 to OFF − − VIDEO MUTE YES To turn the video mute of IC30 to ON PDP-503CMX...
Page 110
− − VARIABLE OUTPUT To set the audio output to variable − − − 3S Y/C MOTION To set the 3D Y/C setting to MOTION − − − 3D Y/C STILL To set the 3D Y/C setting to STILL PDP-503CMX...
3 byte Offset of W/B adjustment value (Offset data) 3 byte (Note 1) Blue (Note 1) : If data are output when the Reference mode is selected, the same data as the reference data are output as the offset data. PDP-503CMX...
Page 112
1: Communication failure Wide microcomputer communication 1 byte 1: Communication failure MAIN IIC 1 byte 1: Communication failure MAIN EEPROM IIC 1 byte 1: Communication failure AUDIO failure 1 byte 1: AUDIO failure FAN failure 1 byte 1: FAN failure PDP-503CMX...
Page 113
(Note 1) (Reference data) 3 byte B-Y LEVEL (Offset data) 3 byte (Note 1) (Note 1) : If data are output when Reference mode is selected, the same data as the reference data are output as the offset data. PDP-503CMX...
Page 114
H.POSITION 3 byte V.POSITION 3 byte CLOCK 3 byte (Note 1) PHASE 3 byte (Note 1) V.SIZE 3 byte (Note 1) When the current input signal mode is VIDEO or INPUT 5(DVI), dummy data(*) are output as adjustment data. PDP-503CMX...
Page 115
Hour meter information of the eighth latest PD 7 byte Upper 5byte: HOUR, Lower 2byte: MINUTE (Note 1) See the table below on PD information Data Power Down Point None Y-DRIVE Y-DC/DC CONVERTER X-DC/DC CONVERTER X-DRIVE Power supply ADDRESS junction ADDRESS resonance DC/DC CONVERTER (DIGITAL) PDP-503CMX...
Page 116
(Note 1) See the table below on SD information Table 2: SD contents GET Data Shut Down Point Panel microcomputer communication failure Module IIC communication failure Condensation Temperature abnormality FAN abnormality Module microcomputer communication failure Wide microcomputer communication failure Main IIC communication failure AUDIO failure PDP-503CMX...
Page 117
(Note 1) As for the setting data not related to the current input function/input signal/setting, dummy data are output. (Note 2) If data are output when the Reference mode is selected, the same data as the reference data are output as the offset data. PDP-503CMX...
Page 118
SUB VOLUME (INPUT4) 2 byte 0 to 60 (Note 1) SUB VOLUME (INPUT5) 2 byte 0 to 60 (Note 1) (Note 1) As for the setting data not related to the current input function/input signal/setting, dummy data are output. PDP-503CMX...
Page 119
TEMPERATURE 3 byte A/D input value (Note 2) HOUR METER 5 byte Unit : H 0: Lock release KEY LOCK 1 byte 1: Lock (Note 1) Dummy data (*) are output when a SLOT manufactured by Pioneer is connected. PDP-503CMX...
Assy I/O Assy SP OUT L ADR CONNECT C RGB Assy Assy Assy ADR RESONANCE Assy SUB ADDRESS B Assy ADR CONNECT B MX LED Assy Assy BRIDGE D Assy ADR CONNECT A CLAMP D Assy Assy Rear View PDP-503CMX...
Wait another 5 seconds, then recover the unit by setting the MAIN POWER X-DC/DC CONVERTER button to ON. X-DRIVE Power supply Note: After power-down is released, the unit restarts and goes in to Standby mode. Address junction Address resonance DIGITAL-DC/DC CONVERTER PDP-503CMX...
Page 122
Block Diagram of the Shutdown Signal System ("STANDBY/ON" LED: Blinking in green) PDP-503CMX...
Page 123
1 byte Seventh latest "SD INFO" 1 byte Shutdown Point OSD Data Panel microcomputer communication failure Module IIC communication failure Condensation Temperature abnormality FAN abnormality Module microcomputer communication failure Wide microcomputer communication failure Main IIC communication failure AUDIO failure PDP-503CMX...
Page 124
Temperature displayed in "INFORMATION" of the Factory menu 1 0 4 T EMP 2 : 0 8 8 T E MP 3 TEMP1 (°C) TEMP1 (data) -50 TEMP2 (°C) TEMP2 (data) /2+5 F A N 1 3 5 TEMP3 (°C) TEMP3 (data) /2+5 PDP-503CMX...
Page 125
: The power is shut down as soon as a failure is detected. Possible causes • Disconnection of a connector between the MX AUDIO Assy (A5) and the RGB Assy (R8). • Short-circuiting between + and - of C8615 and C8622. PDP-503CMX...
Page 126
Block Diagram of the Power Down Signal System ("STANDBY/ON" LED: Blinking red) PDP-503CMX...
Page 127
2.5V UVP P.D. by 2.5V undervoltage (= overcurrent) Reference OVP : Over Voltage Protect UVP : Under Voltage Protect OCP : Over Current Protect : Power Down Note 1: The AC200V P.D. circuit is not mounted in the PDP-503MXE model. PDP-503CMX...
Page 128
Seventh latest "1st PD" point 1 byte Seventh latest "2nd PD" point 1 byte Seventh latest PD time stamp 7 byte Eighth latest "1st PD" point 1 byte Eighth latest "2nd PD" point 1 byte Eighth latest PD time stamp 7 byte PDP-503CMX...
Page 130
Similarly, the switches and the semifixed VRs inside the power- 200V AC). supply module must not be adjusted without a special reason. Setting: For the MXE model only, the switch is set to 200V, and for other models, it is set to 100V. PDP-503CMX...
1 Automatic copying is performed every time the Service Factory mode is entered (regardless of the keyword.) 2 When the power is turned on, keyword checking is performed, then automatic copying is performed if the keyword for the DIGITAL VIDEO Assy (Area B) is "not adjusted," and that for the RGB Assy is "adjusted." PDP-503CMX...
Page 132
After repair, readjustment is required. 2. Except for data for the COLOR and TINT items, data in Area C in the EEPROM of the RGB Assy are assembly-adjustment data. Readjustment is not required when the RGB Assy is replaced with one for service. PDP-503CMX...
SW Power Supply Module Remove the four screws. Remove the SW Power Supply Module. SW Power Supply Module Slit SW Power Supply Module Insert the SW Power Supply Module into the slits of Sub Frame L and R. Diagnosis PDP-503CMX...
Page 134
DIGITAL VIDEO Assy ×2 RGB Base ×2 ×2 ×2 ×2 ×2 Terminal Panel M DIGITAL VIDEO Assy Remove the connectors and binders, and remove the RGB Base with PCB Assys. DIGITAL VIDEO Assy RGB Assy SLOT CONNECTOR Assy RGB Base PDP-503CMX...
Page 135
Remove the Front Case 50. SCAN (A) Assy Front Case 50 ×6 Rear Case (50M) Aluminum Materials The hook of the Front Case 50 is fixed with the Rear Case (50M) and the aluminum material, as shown in the illustration. SCAN (B) Assy PDP-503CMX...
Page 136
Jig Cable (GGD1035). Jig Cable SLOT CONNECTOR Assy (GGD1035) RGB Assy ×2 ×2 ×2 ×2 Video Card Reconnect the Video Card. X DRIVE Assy (Do not insert it into the slot.) Video Card SLOT CONNECTOR Assy RGB Assy Diagnosis PDP-503CMX...
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. • List of IC SN755864APZP, HD64F2328VF, PE1012A, PE1013B, M30624FGAFP, PD6358A, PST9246N, FS781BZB, STK795-470, BA5417, ML6426CS-1, CXA3516R SN755864APZP (SCAN A ASSY : IC6201 - IC6206, SCAN B ASSY : IC6001 - IC6006) Scan IC Pin Assignment (Top view) PDP-503CMX...
Page 138
The high potential circuit power supply which is common to HVO1 - HVO32 − 41, 42, 78, 79 The high potential circuit power supply which is common to HVO33 - HVO64 29, 33, 43, 47 − It is the insulation electrically 77, 80, 83, 96 PDP-503CMX...
Page 139
APLP The APL value acquisition trigger signal input VD_31 The V signal input from IC1401 (PD6358) 3.3V power supply Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus Data bus PDP-503CMX...
Page 140
A clock oscillation child connection terminal NC terminal 3.3V power supply NC terminal A read control terminal from an outside slave device HWRB A wright control terminal to an outside slave device NC terminal NC terminal NC terminal NC terminal NC terminal NC terminal PDP-503CMX...
Page 141
The HD signal input from outside Assy (RGB Assy etc.) The microcomputer mode of operation select signal input The microcomputer mode of operation select signal input The microcomputer mode of operation select signal input NC terminal CS_31Y IC1301, IC1401 (PD6358) control signal CS_31X IC1301, IC1401 (PD6358) control signal PDP-503CMX...
Page 144
, y l l l u l l u t i s c t i x i f t s i x i f PDP-503CMX...
Page 145
Pin Function (2/2) a l l g i l g i l t s i l a i n i l PDP-503CMX...
Page 146
PD6358A (DIGITAL VIDEO ASSY : IC1301, IC1401) Picture Improved IC Pin Function (1/7) ) t r ) t i PDP-503CMX...
Page 147
) t i f i f ) t i ) t i ) t i ) t i ) t i ) t i ) t i ) t i ) t i ) t i ) t i PDP-503CMX...
Page 148
Pin Function (3/7) ) t r ) t i PDP-503CMX...
Page 149
) t i r i f ) t i ) t i ) t i ) t i ) t i f i f ) t i ) t i r i f ) t i PDP-503CMX...
Page 150
Pin Function (5/7) ) t i r i f ) t i ) t r PDP-503CMX...
Page 151
) t i ) t i ) t i ) t i ) t i f i f ) t i r i f ) t i ) t i ) t i ) t r PDP-503CMX...
Page 152
Pin Function (7/7) ) t i ) t i ) t i ) t i ) t i ) t i ) t i PDP-503CMX...
Page 153
PST9246N (DIGITAL VIDEO ASSY: IC1208) Reset IC Block Diagram Pin Assignment (Top View) SOT-25 (TOP VIEW) Pin Function Pin No. Pin name Functions control pin Substate pin GND pin Reset signal output pin pin / voltage detect pin PDP-503CMX...
Page 154
Modulated Clock Frequency Output. The center frequency is the same as the input reference FSOUT CMOS/TTL frequency for FS781. Input frequency is multipled by 2X and 4X for FS782 and FS784 respectively. Power Positive Power Supply Power Power Supply Ground PDP-503CMX...
Page 155
OUT L PGND 36 N.C. 35 POWER GND 34 POWER GND DUMMY 33 POWER GND 32 POWER GND 31 N.C. 30 PL1 N.C. 28 N.C. 26 PC1 25 PC2 24 PC2 PGND DUMMY TR10 23 N.C. 22 PL2 21 PL2 PDP-503CMX...
Page 156
BA5417 (MX AUDIO ASSY: IC8601) Power Amp Block diagram T . S . D S T . B Y F I L T E R Pin Function PDP-503CMX...
Page 157
Internally pulled low. B Unfiltered analog G- or U-channel input for Bank <B>. Sync must be SYNC IN Input for an external H-sync logic provided at SYNC IN pin. signal for filter channels. CMOS level input. Active High. PDP-503CMX...
Page 158
CXA3516R (RGB ASSY: IC4603) AD + PLL IC Pin Assignment (Top view) PDP-503CMX...
8. PANEL FACILITIES PLASMA DISPLAY [PDP-503CMX, PDP-503MXE] MAIN UNIT Note When optional speakers have been connected, the operation panel on the main unit will not be operable. Main unit Operation panel on the main unit 1 Display stand 4 STANDBY/ON button Press to put the display in operation or standby mode.
Page 164
75 W, set this switch to the 2 CONTROL IN/OUT (monaural mini jacks) 2.2 kW position. For connection of PIONEER components that bear the Î mark. Making CONTROL connection enables control 9 AUDIO INPUT (Stereo mini jack) of the plasma display as a component in a system.
Page 165
PLASMA DISPLAY [PDP-503CMX, PDP-503MXE] REMOTE CONTROL UNIT 1 SCREEN SIZE button Press to select the screen size. 2 INPUT buttons Use to select the input. 3 MENU button Press to open and close the on-screen menu. 4 ADJUST (5/∞/3/2) buttons Use to navigate menu screens and to adjust various settings on the unit.
Page 166
2. Set this unit in the stand. CAUTION Because this unit weighs about 88 lbs 3 oz (about 40 kg) and the lack of depth makes it fairly unstable, please use 2 people or more when packing, carrying PDP-503CMX...
Page 167
Installation using the optional PIONEER stand or Wall-mount installation of the unit installation bracket This unit has been designed with bolt holes for ÷ Please be sure to request installation or mounting of this wall-mount installation, etc.. The installation holes that can unit or the installation bracket by an installation be used are shown in the diagram below.