Philips 4101 Series Service Manual page 16

EN 16 5. TPN16.2E LA
Item Item value
16 E_Fuse
17 ORT_MODE
18 AGEING MODE
19 AUD_LIMITE_MODE
20 AUD_THRESHOLD_BYTE1
21 AUD_THRESHOLD_BYTE2
22 AUD_THRESHOLD_BYTE3
23 AUD_GAIN_LINEIN
24 AUD_GAIN_HDMI
25 AUD_GAIN_ATV
26 AUD_GAIN_DTV
27 AUD_GAIN_USB
28 TUNER_ID
29 CIPLUS QUERY
30 CIPLUS UPDATE
31 CI Key Type Selection
32 AQ_TABLE_INDEX
33 EDID UPDATE
34 LVDS SSC Ratio
35 LVDS SSC Freq
36 DDR SSC Ratio
37 DDR SSC Freq
38 Panel H.Flip
39 Panel V.Flip
40 Panel ABSwap
41 Watchdog
42 Backlight PWM freq.(Hz)
43 Backlight PWM Limit
44 VGA_TxRx_Mode
45 LVDS Driving
46 LVDS Format
47 Ziggo Aging
48 SPDIF
49 Standard PWM Gain
50 ECO PWM Gain
51 VGA port
52 Zero Detect Enable
53 Copy PQ table to TV
54 Copy AQ table to TV
55 Headphone
56 EnhancedH/88
57 Joysticker Enable
58 Ambilight Enable
59 Lounge Light Enable
60 FRC F/W Upgrade
61 Satellite Tuner Slave Address
62 912_SSC_LVDS_PERCENT
63 912_SSC_LVDS_FREQ
64 912_LVDS_DRIVING
65 912_LVDS_FORMAT
66 EXIF_FACTORY
How to Exit the Factory mode
Use one of the following methods:
• Select EXIT_FACTORY from the menu and press the "OK"
button.
Note: When the TV is switched "off" by a power interrupt, or
normal switch to "stand-by" while in the factory mode, the TV
will show up in "normal operation mode" as soon as the power
is supplied again. The error buffer will not be cleared.
5.1.4 Customer Service Mode (CSM)
Purpose
The Customer Service Mode shows error codes and
information on the TVs operation settings.The call centre can
instruct the customer (by telephone) to enter CSM in order to
identify the status of the set.This helps the call centre to
diagnose problems and failures in the TV set before making a
service call.
2016-Jul-15
Service Modes, Error Codes, and Fault Finding
Default value
32" 40" 48"
on on on
off off off
off off off
1 1 1
100 100 100
200 200 200
100 100 100
0
-1 -10 -10
-1 0 0
-1 0 0
-1 0 0
0
Press OK
Press OK
ProductKey
18 8 10
Press OK
5% 3% 3%
30KHz 30KHz 30KHz
2% 2% 2%
30KHz 30KHz 30KHz
off off on
off off on
off off off
5sec 5sec 5sec
150 150 150
20 20 20
off off off
3 3 3
VESA 8bit VESA 8bit Jeida 8bit
Press OK
On On On
100 100 100
100 100 100
Off Off Off
on On On
Press OK
Press OK
on On On
on Off On
on On On
Off Off Off
Off Off Off
Press OK
Auto Auto 0xC6
0
0
0
JEDIA 8bit
Press OK
back to
div. table
Description
E-fuse mode
ORT mode
Use this for aging a new LCD panel
Three modes,0: off, 1: adaptive mode, 2: fixed mode
Limit threshold
Limit threshold
Limit threshold
Line-in audio gain
HDMI audio gain
Analogue TV audio gain
Digital TV audio gain
USB audio gain
Displays and changes the Tuner ID with the left and right cursor. Not to be changed when
the tuner is replaced with the correct service part.
Shows the Validity of the CI+ key and the supplier information
Used to enter a new CI+ code into the NVM. This can only be used when no CI+ code exists
in the NVM
CI Key Type Selection
Audio Quality index
Used to enter a new EDID codes into the NVM
LVDS SSC ratio
LVDS SSC frequency
DDR SSC ratio
DDR SSC frequency
Flip panel
Flip panel
ABSwap panel
Watchdog
Backlight PWM frequency
Backlight PWM Limit
VGA_TxRx_Mode
LVDS Driving
LVDS Format
Ziggo Aging
Enable/Disable SPDIF source
Standard PWM Gain
ECO PWM Gain
Enable/Disable VGA port
Zero Detect Enable
Copy PQ table to TV
Copy AQ table to TV
Enable/Disable Headphone source
EnhancedH/88
Joysticker Enable
Ambilight Enable
Lounge Light Enable
FRC F/W Upgrade
TUNER Address
Percent of 912_SSC_LVDS
912_SSC_LVDS_FREQ
912_LVDS_DRIVING
The format for 912_LVDS
Exits the Factory mode
The CSM is a read-only mode; therefore, modifications are not
possible in this mode.
Specifications
• Ignore "Service unfriendly modes".
• Line number for every
line (to make CSM language independent).
• Set the screen mode to full
screen (all contents on screen is visible).
• After leaving the Customer Service Mode, the original
settings are restored.
• Possibility to use "CH+" or "CH-" for channel surfing, or
enter the specific channel number on the RC.
How to Activate CSM
To activate CSM, press the following key sequence on a
standard remote control transmitter: "123654" (do not allow the
display to time out between entries while keying the sequence).