Sony IT-B1 Operating Instructions

Telephone
Operating Instructions
Mode d'emploi (au verso)
IT-B1
Sony Corporation © 1999 Printed in the Philippines
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to
qualified personnel only.
INDUSTRY CANADA NOTICE
NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommunications
network protective, operational and safety requirements as prescribed in the
appropriate Terminal Equipment Technical Requirements document (s). The
Department does not guarantee the equipment will operate to the user's
satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative
designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal meatallic water
pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as
appropriate.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal
device provides an indication of the maximum number of terminal allowed to be
connected to a telephone interface. The termination on an interface may consist
of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Number of all the devices does not exceed 5.
IMPORTANT INSTRUCTION TO USERS
3-866-947-22(1)
• Your model (IT-B1) has been approved by the Industry Canada.
INFORMATION
This Class B digital apparatus complies with Canadian ICES-003.
Note
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Setting up the phone
Connect the phone
2
Telephone line
cord (supplied)
To telephone
outlet
To LINE
jack
Tips
• If your telephone outlet is not modular, contact your telephone
service company for assistance.
• If you want to hang the phone on the wall, see "Mounting the phone
on a wall".
Choose the dialing mode
For the phone to work properly, select an appropriate dialing mode (tone or
pulse).
DIAL MODE
switch
If you aren't sure of your dialing system
Make a trial call with the DIAL MODE switch set to T. If the call connects, leave
the switch as is; otherwise, set to P.
Making and receiving calls
Making a call
(REDIAL)
(MUTING)
TONE (*)
1
Connect the handset cord
(supplied) to the handset, and
to the phone.
2
Connect the telephone line
cord (supplied) to the LINE
jack on the bottom of the
phone, and to a telephone
outlet.
1
Handset cord
(supplied)
Modular
Depending on your dialing system, set
the DIAL MODE switch as follows:
If your dialing system is to Set the switch
Tone T
Pulse P
1
Pick up the handset.
The dialing keys light up.
You hear a dial tone.
2
Dial a phone number.
(FLASH)
3
When you're done talking,
replace the handset in the
cradle.
HANDSET
The call is disconnected.
VOLUME switch
RINGER LEVEL
switch
Receiving a call
When you hear the phone ring, pick up the handset. When you're done talking,
replace the handset in the cradle.
Additional tasks
To
Do this
Adjust the ringer volume
Set the RINGER LEVEL switch to H (high), L (low) or OFF.
Adjust the handset
Set the HANDSET VOLUME switch to H (high), M (middle) or
volume
L (low).
Switch to tone dialing
Press TONE (*) after you're connected.
temporarily
The line will remain in tone dialing until disconnected.
Mute a call
Press and hold (MUTING). While pressing (MUTING) you can
hear the other party but the other party cannot hear you.
Switch to another call
Press (FLASH).
("call waiting" service*)
Press (FLASH) again to get back to the first caller.
* Contact your telephone company to subscribe to this service.
Redialing
You can redial the last number called with just one touch of the (REDIAL) button.
This lets you easily redial the same number again if, for example, the line was
busy.
1
Pick up the handset.
The dialing keys light up. You hear a dial tone.
2
Press (REDIAL).
Note
You can redial the number which consists of up to 31 digits, including a press of tone,
which is counted as one digit.
Mounting the phone on a wall
1
Reverse the hang-up tab.
2
Plug the telephone line cord to the LINE jack and to the telephone
outlet. Use the shorter cord for mounting.
3
Hook the phone to the wall plate.
1
Hang-up
tab
3
Wall plate
Maintenance
On handling
• Do not attempt to disassemble the casing. Refer servicing to qualified
personnel only.
• Do not put foreign objects into the unit. Should any liquid or solid object fall
into the unit, unplug the unit and have it checked by qualified personnel
before operating the unit any further.
• Do not drop the unit as a malfunction may result.
On cleaning
Clean the cabinets with a soft cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine as they may damage the finish of the cabinet.
If you have any questions or problems concerning your phone, please consult
your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made these checks, consult your
nearest authorized Sony dealer.
Remedy
Symptom
• Make sure the telephone line cord is securely
You hear no dial tone.
connected to the telephone outlet.
• Make sure the dial mode setting (tone or pulse) is
The phone does not connect at
correct.
all, even the numbers you dial
are correct.
The phone does not ring.
• Set the RINGER LEVEL switch to H or L.
The phone does not redial • Make sure the number (including the tone digits, if
correctly. used) you last dialed does not exceed 31 digits.
• Make sure the last dialed number is really the one you
want to dial.
Specifications
Dial signal Tone, 10 PPS (pulse) selectable
Approx. 69 × 74.5 × 225 mm (w/h/d)
Dimensions
× 3 × 8
3
(Approx. 2 /
4
Mass Approx. 485 g
(Approx. 17 oz), attachments included
Supplied accessories • Telephone line cords (2)
• Handset cord
Design and specifications are subject to change without notice.
Telephone
line cord
2
7
/ inches)
8