Advertisement
3.
SPECIFICATION
i
Model No.: ...........................................................CP20VRSX
Battery: .................. 20V 2Ah - 6Ah Lithium-ion (not included)
No load speed: ..................................................... 0-3100spm
Motor Power:...................................................................48W
Stroke Length:.............................................................. 28mm
Supply: .............................................................................20V
Cutting specifications ......... Wood -120mm, Soft Metal:10mm
Vibration/Uncertainty: ......................................... 8.20/1.5m/s
Replacement parts:
CP20VMC - Mains Charger (not included)
Consumable parts:
WRS3021/150mm 6tpi Blades (Pack of 5) (not included)
CP20VBP2 - 2Ah Battery, CP20VBP4 - 4Ah Battery, CP20VBP6 - 6Ah Battery (not included)
4.
OPERATION
Blade Clamp
Collet
fig.1
WARNING: Remove battery before fitting tool or maintenance is carried out.
‰
4.1.
To remove the battery from the equipment, depress the spring loaded button on the battery pack. Remove the battery pack by sliding
out. DO NOT touch the metal battery terminals.
4.2.
USING THE TOOL (FIG.1)
4.2.1.
Ensure that you have read, understood and comply with all the safety instructions in Section 1.
4.2.2.
Remove battery from tool. Depress tab on front face of battery and slide battery off the tool.
4.2.3.
To fit the required saw blade rotate the Blade Clamp Collet anticlockwise (fig.1).
4.2.4.
Locate the blade into the Collet (fig.1).
4.2.5.
Release Collet and allow it to return to original position and check firm attachment of blade into collet.
4.2.6.
Refit battery ensuring that the switch locking mechanism is set to the 'Locked' central position (fig.1).
4.3.
ORBITAL / LINEAR CUTTING
4.3.1.
To select Orbital cutting, move the Orbital/Linear Cut lever to the 'ON' position as marked on the body.
4.3.2.
To select Linear cutting, move the Orbital/Linear Cut lever to the 'OFF' position as marked on the body.
4.3.3.
To operate the saw, depress the Trigger Release Button and squeeze the Trigger. Cutting speed is regulated by the trigger.
4.3.4.
When cutting is finished, remove the battery and saw blade.
4.3.5.
Clean the tool, blade and body vents (see Maintenance section 5 below).
4.3.6.
Store in a cool, dry place out of the reach of children.
5. MAINTENANCE
WARNING: Always disconnect the battery before carrying out any inspection, maintenance or cleaning.
‰
5.1.
GENERAL INSPECTION
5.1.1.
Regularly check that all the unit is sound and fit for purpose.
5.1.2.
Repairs should be carried out by an authorised service centre.
5.2.
CLEANING
WARNING: Always wear protective equipment, including eye protection and gloves, when cleaning this tool.
‰
5.2.1.
Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the device's service life.
5.2.2.
Clean the body of your machine with a soft brush, or dry cloth.
5.2.3.
Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a damp cloth is recommended.
5.2.4.
Water must never come into contact with the tool. Ensure the tool is thoroughly dry before using it.
5.2.5.
If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable).
5.3.
LUBRICATION
5.3.1.
Lightly lubricate all moving parts at regular intervals with a suitable spray lubricant.
5.4.
STORAGE
© Jack Sealey Limited
2
Orbital / Linear
Trigger
Cut Lever
Foot Release Lever
Original Language Version
Trigger Release
Button
CP20VRSX Issue 1 17/11/21
Advertisement
