Table of Contents
Advertisement
Available languages
Available languages
English
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: Do not aim toward electrical or other
risk areas.
Installing and Removing the Battery Pack
(Fig. E)
CAUTION: Make sure the battery compartment door is
closed before operating the fan. DO NOT allow water
to enter the battery compartment
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
compartment door
6
. Align the battery pack with the rails
inside the fan's battery compartment and slide it in until
the battery pack is firmly seated and ensure that it does
not disengage. Shut the battery compartment door.
To remove the battery pack from the fan, open the battery
compartment door. Press the release button
pull the battery pack out of the fan's battery compartment.
Insert it into the charger as described in the charger section
of this manual.
Turning the Fan On and Off (Fig. A)
Fan speed is variable and can be adjusted by the fan
button
1
.
To turn the fan on low, press the fan button once.
To turn the fan on medium, press the fan button twice.
To turn the fan on high, press the fan button three times.
To turn off the fan, press the fan button for a fourth time for
1 second. The pump will turn off from any on setting.
nOTE: If you turn on the pump only, the fan will turn on to
the lowest setting.
Pump Switch (Fig. A)
•
To turn the pump on low, press the pump button
once. When turning on the pump, the fan will be turned
on automatically at low speed.
•
To turn the pump on medium, press the pump
button twice.
•
To turn the pump on high, press the pump button
three times.
•
To turn the pump switch off, press the pump button a
fourth time for 1 second. The pump will turn off from any
on setting.
Usage with Water Bucket (Fig. F, G)
WARNING: Do not submerge the fan in the
water bucket.
1. Place the water bucket
level surface.
2. Fill the water bucket with plain, clean water with no
other additives. Do not fill the bucket so it overflows.
3. Set the fan base onto the rim of the water bucket so the
intake tube head
is submerged in the water.
4
nOTE: Do not secure the intake tube
clips
4
while pumping water from the water bucket. The
storage clips are only for storage when not in use
8
into the fan, open the battery
8
9
and firmly
12
(not included) on a flat and
in the storage
7
4. Choose the appropriate setting for the pump. Refer to
Pump Switch for further information.
5. Set your fan setting. Refer to Turning the Fan On and Off
for further information.
nOTE: The fan and water bucket must be moved
seperately. The fan is not attached to the water bucket.
Usage with Garden Hose (Fig. H)
CAUTION: Do not allow water to continue to flow
when the fan is off
1. Set the fan base onto a flat, stable surface.
2. Attach the garden hose
tube head
connector thread.
nOTE: Do not secure the intake tube in the storage
clips
while attached to the garden hose. The storage
11
clips are only for storage when not in use
3. Choose the appropriate setting for the pump. Refer to
Pump Switch for further information.
4. Set your fan setting. Refer to Turning the Fan On and Off
for further information.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Nozzle Maintenance (Fig. E, I, J)
Ensure all misting nozzle maintenance is properly performed.
Leaks can result creating a slip and fall hazard or cause
2
property damage. Irregular mist patterns or leakage may be
the result of a clogged or dirty misting nozzle.
To Clean Nozzles
1. Turn off the fan and the pump.
2. Remove the battery pack
3. Remove the misting nozzles
by rotating them in a counterclockwise direction.
4. Soak the misting nozzles in a de-scaling agent for at least
an hour.
5. Use a brush to clean any foreign materials restricting the
misting nozzles in the front and rear holes while rinsing
with water.
6. Flush the misting nozzles with water.
7. Reconnect the misting nozzles.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
(not included) to the intake
10
, and hand tighten the hose by rotating the
4
.
8
5
from each side of the fan
Advertisement
Table of Contents
