Sealey HT104R Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
1.1. GENERAL SAFETY
Ensure the lamp is fully charged before initial use.
9
DO NOT turn the torch on when it is being charged.
8
DO NOT shine directly into your, other person's or animal's eyes.
8
DO NOT allow children to use the torch.
8
DO NOT handle or move the torch whilst it is being charged.
8
DO NOT use the torch if you suspect that the battery or the torch casing is damaged.
8
DO NOT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery,
8
subsequently recharge the battery at least once every six months of non-use.1.2.
1.2. ELECTRICAL SAFETY
Use only the USB charging lead supplied to charge the battery.
WARNING! It is the user's responsibility to read, understand and comply with the following electrical instructions:
‰
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products, particularly portable equipment which is plugged into an electrical
supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. You must ensure that you:
Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply.
9
DO NOT use if worn or damaged.
8
1.3 BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
‰
DO NOT Attempt to open, disassemble, modify or service the battery pack.
8
DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT Expose to temperatures above 60°C (140°).
8
Replace only with the battery pack designated for this product.
9
Recycle or dispose of used battery as stipulated by local regulation.
9
If the electrolyte in the cells gets on your skin thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention.
2. INTRODUCTION
5W COB LED Striptlight along front of adjustable headband with 3W SMD spotlight on one side. Features auto-sensor which is activated
by pressing the sensor button next to the power button. Supplied with USB Type-C charging lead.
3. SPECIFICATION
Model No: .................................................................HT104R
Battery: ......................................3.7V 1.2Ah Lithium-Polymer
LED Type: .......................................5W COB + 3W LED Bulb
Lumen Output ................................ COB: 350lm, SMD:120lm
Operating Time .............................. 2hr @ 100%, 6hr @ 30%
Charging Time: ..............................................................2.5hr
Operation
© Jack Sealey Limited
5W COB & 3W LED BULB HEAD TORCH WITH
AUTO-SENSOR
HT104R
MODEL NO:
Original Language Version HT104R Issue 1 04/10/21