Page 1
Original instructions Safety Roller Door RD344 Roller door with safe interlocking 2TLC172213M0201 rev. B ABB Jokab Safety Varlabergsvägen 11, SE-434 39 Kungsbacka, Sweden www.abb.com/jokabsafety...
Page 2
DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall responsibility of ABB JOKAB SAFETY for any act exceed the individual price of the product on which liability asserted.
Step 12 – Test run the door ................................. 20 Step 13 – Adjustment of Eden sensors ............................... 20 Step 14 – Fronts....................................20 Stand for mounting ............................21 Checklist for mechanical and electrical installation, test run and adjustments ..22 Troubleshooting ......................23 www.abb.com/jokabsafety 2TLC172213M0201, rev. B...
Page 4
Maintenance........................24 Technical data ........................25 EC Declaration of Conformity ..................26 Connection examples .....................27 2TLC172213M0201, rev. B www.abb.com/jokabsafety...
Introduction Scope These instructions contain information on the efficiency in the use of Safety Roller Door RD344 in accordance with the intended applications. These instructions constitute a part of the scope of the delivery. Audience This document is intended for authorized installation personnel.
• that the width and height of the supplied door match the actual opening (see section 1.2). • when mounting the door in ABB JOKAB Safety’s Quick Guard system; that necessary parts of the fencing system are at hand. •...
Another way of securing that nobody is inside the risk area, when the door is to be operated downwards, is by timed reset. A facility like this is not a part of door and has to be ordered separately. Contact ABB/ JOKAB Safety for more information.
When the frames have to be dismantled the upper parts must be secured with appropriate lifting equipment. Fasten the drive unit when mounting/dismantling • When the drive unit is to be mounted/dismantled it must be secured in appropriate lifting equipment. 2TLC172213M0201, rev. B www.abb.com/jokabsafety...
To protect personnel from being injured by the door it is equipped with a contact strip on the bottom beam profile. If the door hits a person the contact strip will be actuated, and the control system will reverse the door to its fully open position. www.abb.com/jokabsafety 2TLC172213M0201, rev. B...
The lower holes require a long drill (150 mm). Screw the door tight in the wall. Use the pre-drilled holes and at least M10 screws in the upper wall attachments (09/15) and the lower wall Figure 4.3 attachments (36/40). See ”Figure 4.4”. Figure 4.4 2TLC172213M0201, rev. B www.abb.com/jokabsafety...
Fit the other four screws in the bearing plate and wall mounting. Remove the strap that secures the roller. Slide in the door fabric and guides in the frame. Fit the side with the safety sensor first. See ”Figure 4.8”. Figure 4.7 Figure 4.8 www.abb.com/jokabsafety 2TLC172213M0201, rev. B...
½ - ¾ turn. Use a drift that is inserted in a pre-drilled hole. Tighten the locking screw. See ”Figure 4.10a-d”. • Tighten all the screws in the bearing. locking ring with same distance locking screw Figure 4.9 Figure 4.10a Figure 4.10b 1/2 - 3/4 Figure 4.10c Figure 4.10d 2TLC172213M0201, rev. B www.abb.com/jokabsafety...
If the supply voltage is 360-425 V the motor shall be Y-connected. See ”Figure 5.1 - Y-connection”. • If the supply voltage is 208-240 V the motor shall be D-connected. See ”Figure 5.2 - D-connection”. Figure 5.1 - Y-connection Figure 5.2 - D-connection www.abb.com/jokabsafety 2TLC172213M0201, rev. B...
Connection of contact strip 37-44 (X3) Option: Focus II Receiver M12 45-48 (X3) Option: Focus II Transmitter M12 50-51 Safety output; to be connected to the machine 52-53 Safety output; to be connected to the machine 2TLC172213M0201, rev. B www.abb.com/jokabsafety...
Important! The “OPEN” cam switch should be adjusted so that a distance of 60 mm is left between the upper part of the bottom beam profile and the top cover (02). The reason for this is to minimize the risk for personal injuries of squeezing hands or fingers between the bottom beam and top cover. www.abb.com/jokabsafety 2TLC172213M0201, rev. B...
Lift the front (02) into position and screw it against the bearing plates’ collar. • Mount the motor cover (01) on the motor, and wall (03) on the non-motor side. • Install the cable duct protection and decorative moulding (38) for the frame cover. 2TLC172213M0201, rev. B www.abb.com/jokabsafety...
Check that machine/ machines inside risk area is stopped correctly when door leaves its bottom position. Check that chosen safety distance is fulfilled and sufficient for the machinery to stop before operator can reach moving parts. 2TLC172213M0201, rev. B www.abb.com/jokabsafety...
Green Eva within range, safety circuit closed; door closed. LED on Eden Green-Red (flashing) Eva within range; the door is closed but the signal is not OK. Eva out of range, safety circuit open; door open. www.abb.com/jokabsafety 2TLC172213M0201, rev. B...
60 mm between the upper part of the bottom beam and the top cover, • the door blade does not get crinkled in the bottom position 2TLC172213M0201, rev. B www.abb.com/jokabsafety...
EC Declaration of Conformity EC Declaration of conformity (According to 2006/42/EC, Annex 2A) ABB AB declare that the safety components of ABB AB make with type designations and safety JOKAB Safety functions as listed below, are in conformity with the Directives Varlabergsvägen 11...
Forts Cont Standard RD100010 Panel Panel Panel Extern Extern Extern Konstr Design Godk Appr Datum Date Blad Sheet Anmärkning Remark 031113 Rullport Safety RollerDoor Ritad Drawn Sidor Pages Ritn nr Drawing no Forts Cont Standard RD100011 www.abb.com/jokabsafety 2TLC172213M0201, rev. B...
Page 28
Forts Cont Standard RD100012 380 mm 210 mm 380 mm Konstr Design Godk Appr Datum Date Blad Sheet Anmärkning Remark 031113 Rullport Safety RollerDoor Ritad Drawn Sidor Pages Ritn nr Drawing no Forts Cont Standard RD100013 2TLC172213M0201, rev. B www.abb.com/jokabsafety...
Page 29
FOCUS TRANSMITTER M12 PROCESS START OPTION OPTION MACHINE SAFETY STRIP Roller Door Anmärkning Remark Konstr Design Godk Appr Datum Date Blad Sheet 031113 Rullport Safety RollerDoor Ritad Drawn Sidor Pages Ritn nr Drawing no Forts Cont Standard RD100015 www.abb.com/jokabsafety 2TLC172213M0201, rev. B...
Page 30
2TLC172213M0201, rev. B www.abb.com/jokabsafety...