Advertisement
4.3.
Lowering the vehicle
4.3.1. Open the release valve by slowly turning the release knob counter clockwise, wait until the saddle has been fully lowered before
withdrawing the jack from beneath the vehicle.
SAFETY WARNING! Always lower in a slow and controlled manner and ensure that there are no persons or obstacles beneath the
vehicle, or in the path of descent.
5.
MAINTENANCE
IMPORTANT: Only fully qualified personnel should attempt maintenance or repair.
5.1.
When the jack is not in use, the arm should be in the lowest position to minimise corrosion.
5.2.
Keep the jack clean and lubricate all moving parts with oil on a regular basis.
5.3.
Every 3 months grease the upper arm pivot pin via grease nipples.
5.4.
The pump and cylinder form a closed hydraulic system and refilling with oil is only necessary
in exceptional cases.
To check oil level:
1) Place jack on a level surface with the saddle fully lowered.
2) Remove cover plate (fig. 2.2.) and then the filler plug, taking care that no dirt is allowed into the tank.
3) Check that level is to the bottom of the filler plug (fig. 3.). Add oil if necessary.
NOTE: Use a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL.
WARNING: DO NOT use brake fluid, or any fluid other than hydraulic jack fluid as this will cause serious damage to the jack
and will invalidate the warranty!
5.5.
Before each use check for broken, cracked, bent, or loose parts, or any visible damage to ram, pump, saddle, lifting arm, frame and all
parts including nuts, bolts, pins and other fasteners. If any suspect item is found, remove jack from service and take the necessary action
to remedy the problem.
DO NOT use the jack if it is believed to have been subjected to abnormal or shock loading. Inspect and take appropriate action.
5.6.
Periodically check the pump piston and the ram for signs of corrosion. Clean exposed areas with a clean cloth and jack oil.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THIS PRODUCT.
Hydraulic products are repaired by local service agents only. We have service/repair agents in all parts of the UK.
DO NOT RETURN JACKS TO US. Please telephone us on 01284 757500 to obtain the address and telephone number of your local agent.
If jack is under guarantee you can also contact your local dealer.
De-commissioning
Should the jack become completely unserviceable, draw off the oil into an approved container and dispose of the jack and the oil according to
local regulations.
6.
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
Jack will not lift
1) Overloaded
the load properly
2) Release valve not closed
or will not hold
3) Air in system
raised load.
4) Low oil level
5) Internal defect
Jack will not lower
1) Unit requires lubrication
2) Piston rod bent or damaged
3) Jack frame/link system distorted due
to overloading/poor positioning
4) Release valve partially closed
5) Release valve blocked
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
REMEDY
1) Be sure to use jack with adequate capacity.
2) Check and close release valve.
3) Open release valve and pump the handle a few times. Close valve and re-try.
4) Check level and replenish if necessary.
5) Contact Service Agent.
1) Oil all external moving parts.
2) Contact local Service Agent.
3) Replace damaged parts or contact Service Agent.
4) Check and fully open release valve.
5) Clean release valve.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
Fig. 3.
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
10000LQ
Issue: 3 - 31/03/10
Advertisement
