Sealey SMC01.V3 Instructions

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
Keep in dry area
protect from rain
1. Safety
1.1. electrical Safety
WArninG! it is the responsibility of the owner and the operator to read, understand and comply with the following: You must check
‰
all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors
for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A residual
current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current
device (rcd) is used. it is particularly important to use an rcd with portable products that are plugged into a supply which is not
protected by an rccB. if in any doubt consult a qualified electrician. You may obtain a residual current device by
contacting your sealey stockist. You must also read and understand the following instructions concerning electrical safety.
the electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
9
electrician, using a Portble Appliance tester (PAt), at least once a year.
the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and
9
the safety of the appliance operators. if in any doubt about electrical safety, contact a qualified electrician.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
ensure that cables are always protected against short circuit and overload.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure
9
that none are loose.
important: ensure that the voltage marked on the appliance matches the power supply to be used and that
9
the plug is fitted with the correct fuse - see fuse rating to right.
Do not pull or carry the appliance by the power cable.
8
Do not pull the plug from the socket by the cable.
8
Do not use worn or damaged cables, plugs or connectors. immediately have any faulty item repaired or
8
replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is damaged, cut the cable just above the
plug and dispose of the plug safely. fit a new plug according to the following instructions (uK only).
a) connect the Green/YelloW earth wire to the earth terminal 'e'.
b) connect the BroWn live wire to the live terminal 'l'.
c) connect the Blue neutral wire to the neutral terminal 'n'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation extends
beyond the cable restraint and that the restraint is tight.
double insulated products, which are always marked with this symbol
to rewire, connect the wires as indicated below. Do not connect either wire to the earth terminal.
if an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is preferred since any appliance
9
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure
that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the
use of 2.5mm² section cable.
1.2. general Safety
Warning! do not use on AnY otHer BAtteries APArt from seAled leAd Acid BAtteries.
‰
Warning! disconnect the charger from the mains power before servicing or performing any maintenance.
‰
disconnect the charger from the mains power before disconnecting from the battery.
9
maintain the charger in good condition (use an authorised service agent only).
9
Keep the charger clean for best and safest performance.
9
© Jack sealey limited
instructions for
compact auto maintenance battery
charger 3-cycle 12V
model no:
Wear protective electrical
gloves shock
hazard
Original Language Version
Smc01.V3
Warning
Warning:
corrosive explosive
material
substance
, are fitted with live (brown) and neutral (blue) wires only.
use in well
Keep away
ventilated areas
from sources of
ignition
fuSe rating 3 amp
smc01.V3 | issue 1 20/01/17