Page 1
ACCESSORY KIT ZUBEHÖR-SET KIT D'ACCESSOIRES ACCESSOIRE-KIT JUEGO DE ACCESORIOS KIT DI ACCESSORI CU-V70KIT E INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES MANUALE DI INSTRUZIONI LYT0002-0D8A...
Dear Customer, Thank you for purchasing this Accessory KIT. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new Accessory KIT. Using This Instruction Manual •All major sections and subsections are listed in the Table Of Contents ( •Notes appear after most subsections.
Page 3
Warning on lithium cell battery The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C or incinerate. Replace battery with Panasonic (Matsushita Electric), Sanyo or Maxell CR2025; use of another battery may present a risk of fire or explosion.
Page 4
CAUTION! Attaching the camcorder to the Docking Station, connecting cables (AUDIO/ VIDEO, S-VIDEO, Editing, DC) and leaving the unit on top of the TV is not recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage. EN-4 About Batteries DANGER! Do not attempt to take the batteries...
Page 5
The Benefits Of Lithium-Ion Batteries Lithium-ion batteries are small yet have a large power capacity. However, if exposed to extreme cold (below 10°C), the effective operational time decreases significantly. Exposure to temperatures below 0°C will render the battery inoperative. If you are planning to shoot in an environment at these temperatures, carry the battery in a pocket to keep it warm, then attach it just prior to...
Page 6
CAUTIONS BEFORE USE To avoid malfunctions, short circuits, battery leakage, excessive heat and possibly fire ..DO NOT allow the DC Plug to come in contact with metal objects or surfaces..DO NOT use the Power Grip with any appliance other than the GR-DVJ70.
Page 7
1. To avoid hazard ..do not burn..do not short-circuit the terminals..do not modify or disassemble..use only specified chargers. 2. To prevent damage and prolong service life ..do not subject to unnecessary shock..
PROVIDED ACCESSORIES Docking Station Remote control unit Power Grip CU-V778U RM-V708U or RM-V710U Lithium battery CR2025 (for remote control) Battery pack S-VIDEO cable Editing cable AUDIO and VIDEO cable BN-V714U (Phono Docking Station TV or VCR) EN-8...
CONTENTS SAFE PRECAUTIONS PROVIDED ACCESSORIES ABOUT THE POWER GRIP Install Batteries...11 Attach The Power Grip To The Camcorder ...12 Adjust The Grip Band ...13 Record A Scene ...14 Tripod A Mounting ...15 Attaching A Microphone ...16 Specifications ...17 ABOUT THE REMOTE CONTROL UNIT ABOUT THE DOCKING STATION ABOUT THE BATTERY PACK EN-9...
ABOUT THE POWER GRIP The Power Grip enables extended continuous shooting, and makes shooting possible even at 0°C. Lithium Ion batteries are vulnerable in the colder temperatures of winter. Their effectiveness is drastically reduced at temperatures below 10°C, and they will normally not function when the temperature is below 0°C.
Install Batteries Always use two battery packs. The case will not function if only one battery pack is installed. “PUSH” Cover marks Battery Pack Press down "PUSH" and open the cover in the direction of the arrow. Insert two fully charged Battery Packs. •...
ABOUT THE POWER GRIP Attach The Power Grip To The Camcorder Always use two battery packs. The case will not function if only one battery pack is installed. Screw EN-12 (Cont.) Connector cover When detaching the Power Grip, turn the screw opposite the direction indicated by the arrow.
Remove the camcorder’s connector cover as indicated by 1, 2. • In 2, rotate the cover in the direction indicated by the arrow, then remove it. • After use, follow 3, 4 to re-attach the cover. Insert the tips of the metal fittings on the Power Grip deep into the corre- sponding slots on the camcorder (1), then attach the case (2).
ABOUT THE POWER GRIP Record A Scene Insert a cassette and try recording. ** The camcorder’s battery and the Power Grip battery packs cannot be used at the same time. If both are installed, the Power Grip battery packs become the power source. When the Power Grip Battery Packs near complete discharge (when the Power Lamp begins blinking), set the camcorder to RECORD/STANDBY mode, set the Power Dial to “OFF”...
Pull out the viewfinder. Set the Power Dial to “REC”. • The Power Lamp lights and the camcorder enters the Record/Standby mode. • When the battery packs installed in the Power Grip become weak, the case’s Power Lamp begins to blink, and the lamp goes out when the battery packs have completely discharged.
ABOUT THE POWER GRIP Attaching A Microphone You can attach a stereo microphone (commercially available) to the Power Grip. The camcorder does not supply power to the microphone. Refer to the microphone's instruction manual for details on attaching. Accessory shoe EN-16 (Cont.) External MIC...
Pull out the accessory shoe 1 and turn it in the direction of the arrow 2. Insert the microphone's shoe into the accessory shoe. Then connect the microphone's ø3.5 mm mini-plug connector to the external MIC input jack on the camcorder. Specifications Operating temperature 0 —...
ABOUT THE REMOTE CONTROL UNIT For further details, refer to your camcorder's instruction manual. Controls, Indications And Connectors You can use the RM-V708U or RM-V710U to control the camcorder when it's attached to the Docking Station. EN-18 3 2 1 &...
Page 20
ABOUT THE REMOTE CONTROL UNIT Installing The Battery The RM-V708U or RM-V710U uses one lithium battery (CR2025). KNOB Specifications Power : DC 3 V Battery CR2025) Battery Life : Approx. 1 year (depend- ing on usage) Effective distance : Approx. 5 m (front shaft) EN-20 (Cont.) Pull out in the direction of the arrow...
ABOUT THE DOCKING STATION For further details, refer to your camcorder's instruction manual. Controls, Indications And Connectors 1 2 3 45 @ ! 0 9 8 7 Comes on automatically when camcorder is attached; serves to cool the unit down. Take care not to interfere with the blades.
Page 22
JLIP Jack (Joint Level Interface Protocol) • It is used to connect the camcorder to a device such as a personal computer. For further detail consult your nearest JVC & dealer. Information (in English) is also available at our home page: http://www.jvc- victor.co.jp/...
Page 23
Specifications Operating temperature Editing connector S-Video connectors Video output connector Audio output connector JLIP connector Multi connector Dimensions Weight * E. & O. E. Design and specifications subject to change without notice. : 0°C — 40°C (when charging, 10°C — 35°C) : ø3.5 mm : 1 Vp-p, 75 ¸...
For further details, refer to your camcorder's instruction manual. CAUTIONS: This is a lithium-ion type battery pack, and is intended for use with the JVC Digital Video Camera only. Use only the AC Power Adapter/Charger designed exclusively for the Digital Video Camera. Use of another battery charger may result in incomplete charging, malfunctions and risk of fire.
Page 25
Charge Maker BLACK CHARGE MARKER • The charge marker does not move by itself. After charging or removing a discharged battery, be sure to set the marker to the predetermined position. Specifications Power Dimensions Weight The charge marker makes it easy for you to differentiate between charged and discharged batteries.