Engine Tightening Torques - Yamaha Fascino S 2021 Supplementary Service Manual

EAS20013

ENGINE TIGHTENING TORQUES

Item
Cylinder head nut (initial torque)
Cylinder head nut (final torque)
Spark plug
Cylinder head bolt
Cylinder head stud bolt (for muffler)
Oil check bolt
Cylinder head cover bolt
Timing chain guide stopper bolt
Valve clearance adjusting screw
locknut
Camshaft sprocket bolt
Timing chain tensioner assembly
bolt
Cam shaft retainer bolt
Air shroud bolt (right)
Air shroud screw (left and right)
Fan bolt
Oil pump assembly screw
Oil strainer bolt
Intake manifold joint bolt
Injector bolt
Air filter case assembly bolt
Throttle body and intake manifold
bolt
Air filter case joint clamp screw
Exhaust installing bolt
Exhaust protector bolt
Exhaust pipe nut
Left and right crankcase bolt
Oil pump cover bolt
Transmission case cover bolt
Transmission oil drain bolt
Crankcase stud bolt
Engine oil drain bolt
TIGHTENING TORQUES
Thread
Q'ty
size
10 N·m (1.0 kgf·m, 7.4 lb·ft)
M8 4
27 N·m (2.7 kgf·m, 20 lb·ft)
M10 1 13 N·m (1.3 kgf·m, 9.6 lb·ft)
M6 2 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M8 2 15 N·m (1.5 kgf·m, 11 lb·ft)
M6 1 7 N·m (0.7 kgf·m, 5.2 lb·ft)
M6 4 11 N·m (1.1 kgf·m, 8.1 lb·ft)
M6 1
M5 2 7 N·m (0.7 kgf·m, 5.2 lb·ft)
M5 2 8 N·m (0.8 kgf·m, 5.9 lb·ft)
M6 2 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M6 1 12 N·m (1.2 kgf·m, 8.9 lb·ft)
M6 3 8 N·m (0.8 kgf·m, 5.9 lb·ft)
M6 6 1.3 N·m (0.13 kgf·m, 0.95 lb·ft)
M6 3 8 N·m (0.8 kgf·m, 5.9 lb·ft)
M5 2 4 N·m (0.4 kgf·m, 3.0 lb·ft)
M30 1 20 N·m (2.0 kgf·m, 15 lb·ft)
M6 2 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M6 1 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M6 2 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M6 2 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M4 1 2.5 N·m (0.25 kgf·m, 1.8 lb·ft)
M8 2 31 N·m (3.1 kgf·m, 23 lb·ft)
M6 2 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M8 2 15 N·m (1.5 kgf·m, 11 lb·ft)
M6 10 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M6 3 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M6 7 10 N·m (1.0 kgf·m, 7.4 lb·ft)
M8 1 20 N·m (2.0 kgf·m, 15 lb·ft)
M8 4 13 N·m (1.3 kgf·m, 9.6 lb·ft)
M12 1 20 N·m (2.0 kgf·m, 15 lb·ft)
2-10
Tightening torque
7 N·m (0.7 kgf·m, 5.2 lb·ft)
SPEC
Remarks
M
with gasket
M
Apply
TB1215 to
screw
thread.
LT
LT
Tighten until
contacting
collar.
with gasket
Tip:Longer
side of
thread
length shall
be screwed
at crancase.