Mitsubishi Electric E70 Series Connection Manual
  1. Manuals
  2. Brands
  3. Mitsubishi Electric Manuals
  4. Control Systems
  5. E70 Series
  6. Connection manual

Mitsubishi Electric E70 Series Connection Manual

Hide thumbs Also See for E70 Series:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for Mitsubishi Electric E70 Series

Summary of Contents for Mitsubishi Electric E70 Series

  • Page 2 Introduction This manual covers the items required for installing and connecting the MITSUBISHI CNC E70 Series. Read this manual thoroughly and understand the product's functions and performance before starting to use. This manual is written on the assumption that all optional functions are added, but the actually delivered device may not have all functions.
  • Page 3 Refer to the following documents. M700V/M70V/E70 Series PLC Interface Manual ..IB-1500920 MDS-DM2 Series Specifications Manual ..IB-1501136 MDS-DM2 Series Instruction Manual ..IB-1501139 MDS-DJ Series Specifications Manual ..IB-1501130 MDS-DJ Series Instruction Manual ..IB-1501133 Safety Handbook (Original Instructions) ..IB-1501025...
  • Page 4 Precautions for Safety Always read this manual and enclosed documents before installation, operation, maintenance and inspection to ensure correct usage. Thoroughly understand the basics, safety information and precautions of the devices before using. This manual classifies the safety precautions into "DANGER", "WARNING" and "CAUTION". DANGER When the user could be subject to imminent fatalities or serious injuries if handling is mistaken.
  • Page 5 For Safe Use Mitsubishi CNC is designed and manufactured solely for applications to machine tools. Do not use this product in any applications other than those specified as above, especially those which are substantially influential on the public interest or which are expected to have significant influence on human lives or properties.
  • Page 6 3. Items related to prevention of bodily injury or property damage DANGER When transporting or installing a built-in IPM spindle or linear servomotor, be careful so that your hand or property will not be trapped in the motors or other metal objects. Also keep the devices with low magnetic tolerance away from the product.
  • Page 7 4. General precautions Always follow the precautions below. Incorrect handling could result in faults, injuries or electric shocks, etc. (1) Transportation and installation CAUTION Correctly transport the products according to the mass. Use motor’s suspension bolts to transport the motor itself. Do not use it to transport the motor after installation onto the machine.
  • Page 8 CAUTION Always install the motor with reduction gear in the designated direction. Failure to observe this could result in oil leaks. Always install a cover, etc., over the shaft so that the rotary section of the motor cannot be touched during motor rotation.
  • Page 9 (2) Items related to wiring CAUTION Correctly wire this product. Failure to observe this could result in motor runaway, etc. Do not install a phase advancing capacitor, surge absorber or radio noise filter on the output side of the drive unit. Correctly connect the output side (terminal U, V, W).
  • Page 10 (3) Adjustments CAUTION Check and adjust programs and each parameter before starting operation. Failure to observe this could result in unpredictable operations depending on the machine. Do not make drastic adjustments or changes as the operation could become unstable. (4) Usage CAUTION Install an external emergency stop circuit so that the operation can be stopped and the power turns OFF immediately when unforeseen situation occurs.
  • Page 11 (5) Troubleshooting CAUTION Use a motor with electromagnetic brakes or establish an external brake mechanism for the Shut off with motor Shut off with CNC brake purpose of holding; this serves as brake control output control PLC output countermeasures for possible hazardous situation caused by power failure or product fault.
  • Page 12 (6) Maintenance, inspection and part replacement CAUTION Periodically back up the programs, tool data and parameters to avoid potential data loss. Also, back up those data before maintenance and inspections. When replacing the battery on the controller side, the machining programs, tool data and parameters should be backed up with the input/output device beforehand.
  • Page 14 Treatment of waste The following two laws will apply when disposing of this product. Considerations must be made to each law. The following laws are in effect in Japan. Thus, when using this product overseas, the local laws will have a priority.
  • Page 16 This symbol mark is according to the directive 2006/66/EC Article 20 Information for end- users and Annex II. Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and/or reused. This symbol means that batteries and accumulators, at their end-of-life, should be disposed of separately from your household waste.
  • Page 18 Trademarks MELDAS, MELSEC, EZSocket, EZMotion, iQ Platform, MELSOFT, GOT, CC-Link, CC-Link/LT and CC-Link IE are either trademarks or registered trademarks of Mitsubishi Electric Corporation in Japan and/or other countries. Ethernet is a registered trademark of Xerox Corporation in the United States and/or other countries.
  • Page 20 本製品の取扱いについて ( 日本語 /Japanese) 本製品は工業用 ( クラス A) 電磁環境適合機器です。販売者あるいは使用者はこの点に注意し、住商業環境以外で の使用をお願いいたします。 Handling of our product (English) This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 본...

  • Page 22: Table Of Contents

    Contents 1 System Configuration..........................1 1.1 System Basic Configuration Drawing..................... 2 1.2 General Connection Diagram ........................ 3 1.3 List of Configuration ..........................5 1.3.1 List of Units ............................ 5 1.3.2 Durable Parts ..........................6 1.3.3 Replacements ..........................6 1.3.4 List of Cables ..........................7 2 General Specifications ..........................
  • Page 23 4.2.10 Connecting with Safety Observing I/O Device ................92 4.3 Connection of Operation Panel I/O Unit....................93 4.3.1 Operation Panel I/O Unit Connection System Drawing ............... 93 4.3.2 Connecting with Keyboard Unit....................94 4.3.3 Connecting with Manual Pulse Generator (MPG)................ 95 4.3.3.1 Handle Numbers ........................
  • Page 24 Appendix 1.41 List of Cable Connector Sets ................... 161 Appendix 2 EMC Installation Guidelines ....................163 Appendix 2.1 Introduction ........................164 Appendix 2.2 EMC Directives ........................164 Appendix 2.3 EMC Measures ........................165 Appendix 2.4 Panel Structure ........................165 Appendix 2.4.1 Measures for Control Panel Body ................165 Appendix 2.4.2 Measures for Door .....................

  • Page 26: System Configuration

    System Configuration...

  • Page 27: System Basic Configuration Drawing

    MITSUBISHI CNC 1 System Configuration 1.1 System Basic Configuration Drawing Keyboard unit Display unit Remote I/O unit Control unit Manual pulse generator Operation panel I/O unit Remote I/O unit Manual pulse generator Synchronous feed encoder Servo/Spindle drive units Motors (Note 1) Control unit is mounted on the back side of the display unit. (Note 2) Operation panel I/O unit is mounted on the back side of the keyboard unit.

  • Page 28: General Connection Diagram

    E70 Series Connection Manual 1.2 General Connection Diagram 1.2 General Connection Diagram Dotted lines indicate the sections prepared by the machine tool builder. <> Angle brackets indicates attached cable of unit. Round brackets indicates former product model number. L1 L2 L3...
  • Page 29 MITSUBISHI CNC 1 System Configuration [Analog Spindle Configuration] Dotted lines indicate the sections prepared by the machine tool builder. <> Angle brackets indicates attached cable of unit. Round brackets indicates former product model number. L1 L2 L3 CNC control unit No-fuse breaker (NFB) FCU7-MU528(FCU7-MU558) <G497>...

  • Page 30: List Of Configuration

    E70 Series Connection Manual 1.3 List of Configuration 1.3 List of Configuration 1.3.1 List of Units Classification Type Components Remarks [Control unit] Main control card Export Tarde Control Order and Foreign NC functions FCU7-MU528 Memory card (HN451) Exchange Order noncompliant unit...

  • Page 31: Durable Parts

    MITSUBISHI CNC 1 System Configuration Classification Type Components Remarks [External power supply unit] External power supply with power supply Power supply card Input 200VAC PD25 ON/OFF function Case set Output 24VDC (3A) [Manual pulse generator] UFO-01-2Z9 Input 5VDC 5V Manual pulse generator UFO-01-2Z9 (Produced by NIDEC NEMICON) 100pulse/rev...

  • Page 32: List Of Cables

    E70 Series Connection Manual 1.3 List of Configuration 1.3.4 List of Cables Length (m) of cables provided Max. cable Type Application by Mitsubishi length CNP2E-1-xM Motor side PLG cable 2, 3, 4, 5, 7, 10, 15, 20, 25, 30 CNP3EZ-2P-xM...
  • Page 33 MITSUBISHI CNC 1 System Configuration Length (m) of cables provided Max. cable Type Application by Mitsubishi length MR-BKS1CBLxM- Brake cable for HF-KP motor (load side angle) 2, 3, 5, 7, 10 A1-H MR-BKS1CBLxM- Brake cable for HF-KP motor (reverse load side angle) 2, 3, 5, 7, 10 A2-H MR-PWS1CBLxM-...

  • Page 34: General Specifications

    General Specifications...

  • Page 35: Environment Conditions

    MITSUBISHI CNC 2 General Specifications 2.1 Environment Conditions Operation panel Machine operation Unit name Control unit Display unit Keyboard unit I/O unit panel Item FCU7-MU528 FCU7-DX621/711/ Type FCU7-DU120-13 FCU7-KB024/025 FCU7-KB921/926 (FCU7-MU558) 721/731 During 0 to 55C° operation Ambient temperature During -20 to 60C°...

  • Page 36: Control Unit

    E70 Series Connection Manual 2.2 Control Unit 2.2 Control Unit Dimension and names of parts [FCU7-MU528(FCU7-MU558)] (10) (11) (12) (13) (14) (15) (16) (17) (18) Connector Connector Function Function name name Front USB memory I/F (11) RIO1 Remote I/O unit I/F...
  • Page 37 MITSUBISHI CNC 2 General Specifications (2) Front CF card I/F (CF) It is recommended to use CF cards of the original equipment manufactured parts. Mitsubishi is unable to guarantee the machine operation when a commercially available CF card or SD memory card (SD-CF adapter is required) is used.
  • Page 38 E70 Series Connection Manual 2.2 Control Unit (5) External emergency stop input (EMG) EMG IN +24V * Be sure to connect EMG terminal cable (G123) to the connector when not used. <Cable side connector type> Connector: 005057-9403 Contact: 0016020103 Recommended manufacturer: MOLEX...
  • Page 39 MITSUBISHI CNC 2 General Specifications (9) Ethernet I/F (LAN) * Connect connector case with FG pattern. * Use cross cable (G300) when directly connecting a device such as a personal computer to the unit. <Cable side connector type> Connector: 5-569550-3 Recommended manufacturer: Tyco Electronics (10) Operation panel I/O unit I/F (CG71) 3.3V...
  • Page 40 E70 Series Connection Manual 2.2 Control Unit (11) Remote I/O unit I/F (RIO1) Up to eight remote I/O stations can be connected. TXRX1 TXRX1* <Cable side connector type> Connector: 1-178288-3 Contact: 1-175218-2 x3 Recommended manufacturer: Tyco Electronics (12) Menu key I/F (MENUKEY) (13) Encoder input 1ch/ 5V manual pulse generator input 2ch (ENC) Synchronous feed encoder or 5V manual pulse generator can be connected to this connector.
  • Page 41 MITSUBISHI CNC 2 General Specifications (a) Input for synchronous feed encoder <Specification of input part> Three phases (A phase, B phase, a phase difference 90 degrees, Number of pulse phases Z phase) (Refer to the waveform below.) Signal output of the encoder Line driver output Input voltage range 0V to 5.25V...
  • Page 42 E70 Series Connection Manual 2.2 Control Unit (c) 5V manual pulse generator input/output circuit Connector pin No. HA1A HA2A Signal input HA1B HA2B Control circuit Power output When using the synchronous feed encoder and the manual pulse generator at the same time, connect the manual pulse generator to the operation panel I/O unit or use a distribution cable made by the machine tool builder.
  • Page 43 MITSUBISHI CNC 2 General Specifications (a) Skip signal input conditions Use the input signal within the following condition ranges. 24V common 0V common Input voltage at external contact ON 6V or less 18V or more, 25.2V or less Input current at external contact ON 6mA or more Input voltage at external contact OFF 20V or more, 25.2V or less...
  • Page 44 E70 Series Connection Manual 2.2 Control Unit (15) Serial communication (RS-232C) I/F 2ch (SIO) RD1(RXD1) SD1(TXD1) CS1(CTS1) RS1(RTS1) DR1(DSR1) ER1(DTR1) RD2(RXD2) SD2(TXD2) CS2(CTS2) RS2(RTS2) DR2(DSR2) ER2(DTR2) * Connect connector case with FG pattern. <Cable side connector type> Plug: 10120-3000VE Shell: 10320-52F0-008...
  • Page 45 MITSUBISHI CNC 2 General Specifications (18) LED   Name Name Function At fault Conditions (1) Failure of 24VDC input 24VDCIN 24VDC input check Not lit (2) Fuse is disconnected near DCIN connector (1) Failure of internal voltage output in control unit DCOUT Internal output voltage check Not lit (2) Short circuit of 5VDC output on CG71 or ENC...

  • Page 46: Display Unit

    E70 Series Connection Manual 2.3 Display Unit 2.3 Display Unit Outline dimension [FCU7-DU120-13 (8.4-type)] 110( Space required for wiring) (Note 1) The above side view shows the state with the control unit mounted. (Note 2) Consider the minimum radius value of optical communication cable for the bottom space. (Refer to "Connection : Precautions for Using Optical Communication Cable".)

  • Page 47: Keyboard Unit

    MITSUBISHI CNC 2 General Specifications 2.4 Keyboard Unit Outline dimension [FCU7-KB024 (8.4-type)] 110 ( Space required for wiring (Note) The above side view shows the state with the operation panel I/O unit FCU7-DX721 mounted. <Panel cut dimension drawing> (Unit outline) 13 0 (Square hole) 4-M3 Screw...
  • Page 48 E70 Series Connection Manual 2.4 Keyboard Unit [FCU7-KB025 (8.4-type)] 110 (Space required for wiring) (Note) The above side view shows the state with the operation panel I/O unit FCU7-DX721 mounted. <Panel cut dimension drawing> (Unit outline) 13 0 (Square hole)

  • Page 49: Operation Panel I/O Unit

    MITSUBISHI CNC 2 General Specifications 2.5 Operation Panel I/O Unit Characteristics of operation panel I/O unit are as follows. (1) Number of DI/DO points that can be mounted on the machine operation panel is 64/64 at the minimum and 96/96 at the maximum.
  • Page 50 E70 Series Connection Manual 2.5 Operation Panel I/O Unit Dimension and names of parts [FCU7-DX621] 110 ( Space required for wiring) (10) (11) (12) (13) <Dimension drawing for installing on the panel> <Installation on the back side of the keyboard>...
  • Page 51 MITSUBISHI CNC 2 General Specifications [FCU7-DX711] 110 ( Space required for wiring) (10) (11) (12) (4) (5) (13) <Dimension drawing for installing on the panel> <Installation on the back side of the keyboard> Operation panel I/O unit can be installed on the back side 116 ( Unit outline of the keyboard.
  • Page 52 E70 Series Connection Manual 2.5 Operation Panel I/O Unit [FCU7-DX721/ FCU7-DX731] 110 ( Space required for wiring) (10) (11) (12) (4) (5) (13) (Note) (9) is not available for FCU7-DX731. <Dimension drawing for installing on the panel> <Installation on the back side of the keyboard>...
  • Page 53 MITSUBISHI CNC 2 General Specifications (1) Machine input (CG31) Digital input 32 points (1st station) (2) Machine input (CG33) Digital input 32 points (2nd station) (Note) This is not available for FCU7-DX621. (3) Machine input (CG35) Digital input 32 points (3rd station) (Note) This is not available for FCU7-DX711.
  • Page 54 E70 Series Connection Manual 2.5 Operation Panel I/O Unit (a) Outline of digital signal input circuit Both 24V common and 0V common connections are allowed in the digital signal input circuit. Follow the wiring diagram below for each type. Input circuit...
  • Page 55 MITSUBISHI CNC 2 General Specifications (4) Machine output (CG32) Digital output 32 points (1st station) (5) Machine output (CG34) Digital output 32 points (2nd station) (Note) This is not available for FCU7-DX621. (6) Machine output (CG36) FCU7-DX731: Digital output 32 points (3rd station) FCU7-DX621/DX721: Digital output 16 points (3rd station) (with analog output) (Note) This is not available for FCU7-DX711.
  • Page 56 E70 Series Connection Manual 2.5 Operation Panel I/O Unit (a) Outline of digital signal output circuit Use within the specification ranges shown below. Output circuit (Macine side) CG32/CG34/CG36 24VDC(+) Control Circuit Source type (DX621/DX7x1) : Relay : Pilot lamp Output conditions...
  • Page 57 MITSUBISHI CNC 2 General Specifications (7) Keyboard I/F (NCKB) (8) FG terminal (FG) (9) Analog output 1ch (AO) (Note) This is not available for FCU7-DX731. * Connect connector case with FG pattern. <Cable side connector type> Plug: 10120-3000VE Shell: 10320-52F0-008 Recommended manufacturer: 3M Output circuit Output conditions...
  • Page 58 E70 Series Connection Manual 2.5 Operation Panel I/O Unit (10) Manual pulse generator input 2ch (5V and 12V) (MPG) 5V manual pulse generator and 12V manual pulse generator can be connected to this connector. Connect the synchronous feed encoder to the ENC connector of the control unit.
  • Page 59 MITSUBISHI CNC 2 General Specifications <Input/output circuit> Connector pin No. HA1A HA2A Signal input HA1B HA2B Control unit +12V +12V Power output Power output (11) Remote I/O unit I/F (RIO3) TXRX3 TXRX3* 0V(GND) <Cable side connector type> Connector: 1-178288-3 Contact: 1-175218-2 x3 Recommended manufacturer: Tyco Electronics Refer to the following chart for the maximum number of connecting stations and I/O points.
  • Page 60 E70 Series Connection Manual 2.5 Operation Panel I/O Unit (13) LED Name Function At fault Conditions 3VON 3VDC input check Not lit (1) Disconnection between control unit and operation panel I/O unit (1) Disconnection between control unit and operation panel I/O unit...

  • Page 61: Remote I/O Unit

    MITSUBISHI CNC 2 General Specifications 2.6 Remote I/O Unit The following four types of signals can be input/output from the remote I/O unit (FCUA-DX1x1) according to the type and No. of contacts. Use serial link connections to connect the unit with the control unit or the operation panel I/O unit. Multiple remote I/O units can be used as long as the total number of occupied stations is eight or less.
  • Page 62 E70 Series Connection Manual 2.6 Remote I/O Unit Dimension and names of parts [Front view] (11) (11) (11) (DX101) (DX111/DX121) (DX141) [Bottom view] [Side view] (Front) (10) (Rear) <Installation dimension drawing> Mounting hole 2-M5 screw Bottom...
  • Page 63 MITSUBISHI CNC 2 General Specifications (1) Machine input (DI-L) (2) Machine input (DI-R) Both 24V common and 0V common connections are allowed in the digital signal input circuit. Follow the wiring diagram below for each type. Input circuit 24V common 0V common DI-L / DI-R DI-L / DI-R...
  • Page 64 E70 Series Connection Manual 2.6 Remote I/O Unit (3) Machine output (DO-L) (4) Machine output (DO-R) Use within the specification ranges shown below. Output circuit DO-L/DO-R (Machine side) 24VDC(+) Control circuit Source type (DX1x1) Output conditions Insulation method Non-insulation Rated load voltage 24VDC Max.
  • Page 65 MITSUBISHI CNC 2 General Specifications [Outline of analog signal output circuit] The analog signal output circuit can be used only for FCUA-DX121. Output circuit 0V(RG) Output conditions Output voltage 0V to ±10V (±5%) Resolution 12bit (±10V × n/4096) (Note) Load conditions 10kΩ...
  • Page 66 E70 Series Connection Manual 2.6 Remote I/O Unit (5) Analog signal input/output (AIO) (a) Outline of analog signal output circuit The analog signal output circuit can be used only for FCUA-DX141. Output circuit 0V(RG) Output conditions Output voltage 0V to ±10V (±5%) Resolution 12bit (±10V ×...
  • Page 67 MITSUBISHI CNC 2 General Specifications (6) Transfer speed changeover switch (DS) Not used Not used (7) Station No. changeover switch (CS) Selection of station No. (8) Remote I/O unit I/F #1 (RIO1) (9) Remote I/O unit I/F #2 (RIO2) TXRX TXRX* <Cable side connector type>...

  • Page 68: External Power Supply Unit

    E70 Series Connection Manual 2.7 External Power Supply Unit 2.7 External Power Supply Unit Item PD25 200 to 230VAC Input power voltage +10%-15% 50/60Hz±1Hz Output current Dimension 130mm × 65mm × 230mm Mass 1.5kg Output holding time 300ms (Note 1) PD25 will not be turned ON by the ON/OFF switch immediately after the power OFF. Wait at least 2 seconds, and then turn the power ON.
  • Page 69 MITSUBISHI CNC 2 General Specifications (1) AC power input (ACIN) ACIN N ACIN H <Cable side connector type> Connector: 2-178128-3 Contact: 1-175218-5 × 3 Recommended manufacturer: Tyco Electronics (2) ON/OFF switch (ON/OFF SW) Switch ON (upward): 24VDC output Switch OFF (downward): 24VDC output OFF (3) ON/OFF input (ON/OFF) P-OFF P-ON...

  • Page 70: Manual Pulse Generator

    E70 Series Connection Manual 2.8 Manual Pulse Generator 2.8 Manual Pulse Generator [UFO-01-2Z9] 5V Manual Pulse Generator (100 pulse/rev) <Outline dimension drawing> Gasket 3- M4 stud Index Panel cut diameter 72 at equal pitch Above size only <Panel cut drawing>...
  • Page 71 MITSUBISHI CNC 2 General Specifications [HD60C] 12V Manual Pulse Generator (25 pulse/rev) Packing t 2.0 3-M4 stud bolt  L10 Installation of screws other than M3 x 6 8.89 7.60 not possible 24 27 0.5 <Panel cut dimension drawing> 4. 8 (Divide equally by three) 120°...

  • Page 72: Synchronous Feed Encoder

    E70 Series Connection Manual 2.9 Synchronous Feed Encoder 2.9 Synchronous Feed Encoder Dimension and names of parts [OSE-1024-3-15-68] Caution plate 5. 4 hole 19. 5 14. 3 - 0. 11 - 0. 006 - 0. 012 - 0. 017 - 0. 042 +0.

  • Page 73: Mitsubishi Cnc Machine Operation Panel

    MITSUBISHI CNC 2 General Specifications 2.10 MITSUBISHI CNC Machine Operation Panel 2.10.1 MITSUBISHI CNC Machine Operation Panel A Outline dimension [FCU7-KB921 (MITSUBISHI CNC machine operation panel A)] (Space required for wiring) <Panel cut dimension drawing> (Unit outline) (Square hole) 4-M3 Screw...
  • Page 74 E70 Series Connection Manual 2.10 MITSUBISHI CNC Machine Operation Panel Connector No. Connector name Function No. Connector name Function DCIN 24VDC input FG terminal DCOUT 24VDC output Relay wiring Mahine operation panel B RIOIN Remote I/O SUBP switch (1)(2) 24VDC input/output (DCIN/DCOUT) I/O +24V <Cable side connector type>...
  • Page 75 MITSUBISHI CNC 2 General Specifications (3) Remote I/O connected connector (RIOIN) I/O TXRX I/O TXRX* <Cable side connector type> Connector: 1-178288-3 Contact: 1-175218-2 x3 Recommended manufacturer: Tyco Electronics (4) FG terminal (FG) (5) Relay wiring (EXT) Relay EMGCOM Relay EMG Relay 6 Relay 5 Relay 4...
  • Page 76 E70 Series Connection Manual 2.10 MITSUBISHI CNC Machine Operation Panel Machine operation panel B switch (SUBP) Relay EMGCOM Relay EMG Relay 6 Relay 5 Relay 4 Relay 3 Relay 2 Relay 1 Spare SW(X75) Spare SW(X74) Spare SW(X73) Selector SW(X72)
  • Page 77 MITSUBISHI CNC 2 General Specifications Wiring of machine operation panel B <Wiring of rotary switch (SUBP)> Machine Operation Panel I/F PCB HN232 Machine operation panel B 1kΩ [SUBP] (FCU7-KB926) Rotary Switch (RSW1) (For cutting override) 21 position Real gray code Rotary Switch (RSW2) (For spindle override)
  • Page 78 E70 Series Connection Manual 2.10 MITSUBISHI CNC Machine Operation Panel <Wiring of other switches (SUBP)> Machine Operation Panel I/F PCB HN232 [SUBP] Machine operation panel B 1kΩ (FCU7-KB926) Selector Switch (For memory protection) 2 notch Key shape 2c Manual return type...
  • Page 79 MITSUBISHI CNC 2 General Specifications <Connection when the selector SW has 3 notches> [SUBP] Selector SW 3 notch 2a2b Manual return type <Connection when relaying wiring to control panel> [EXT] P-ON PONCOM Connection with (0V) P-ON/OFF Switch POFF P-OFF POFFCOM (0V) EMGCOM Connection using two contacts...

  • Page 80: Mitsubishi Cnc Machine Operation Panel B

    E70 Series Connection Manual 2.10 MITSUBISHI CNC Machine Operation Panel 2.10.2 MITSUBISHI CNC Machine Operation Panel B Outline dimension [FCU7-KB926 (MITSUBISHI CNC machine operation panel B)] (Space required for wiring) <Panel cut drawing> (Unit outline) (Square hole) 4-M3 Screw...
  • Page 81 MITSUBISHI CNC 2 General Specifications Connector Switch Switch (1) Memory protection switch (3) Spindle override (RSW2) (2) Emergency stop button (4) Cutting override (RSW1) (1) Memory protection switch <Contact configuration> Contact 2 Contact 1 Contact 1(Common) Contact 1(A contact) Contact 1(B contact) Contact 2(Common) Contact 2(A contact) Contact 2(B contact)
  • Page 82 E70 Series Connection Manual 2.10 MITSUBISHI CNC Machine Operation Panel (2) Emergency stop button Contact 1(A contact) Contact 1(A contact) Contact 2(B contact) Contact 2(B contact) Contact 3(A contact) Contact 3(A contact) Contact 4(B contact) Contact 4(B contact) <Switch type>...
  • Page 83 MITSUBISHI CNC 2 General Specifications (4) Cutting override (RSW1) Output signal 1 Output signal 3 Output signal 5 Common terminal Output signal 4 Output signal 2 Output signal 6 <Switch type> Switch: AC09-GY0/20L3B02 Recommended manufacturer: Fuji Electric Connection: Connector <Switch side connector type> Connector: IL-7P-S3EN2 Recommended manufacturer: Japan Aviation Electronics <Cable side connector type>...

  • Page 84: Exclusive Cf Cards For Mitsubishi Cnc

    E70 Series Connection Manual 2.11 Exclusive CF Cards for MITSUBISHI CNC 2.11 Exclusive CF Cards for MITSUBISHI CNC Item FCU7-CF256M FCU7-CF002G Capacity 256MB Operation-guaranteed -40 ℃ to +85 ℃ temperature NAND Flash SLC (Note) (Note) SLC stands for Single Level Cell, and it stores one bit data in each memory cell.
  • Page 85 MITSUBISHI CNC 2 General Specifications...

  • Page 86: Installation

    Installation...

  • Page 87: Heat Radiation Countermeasures

    MITSUBISHI CNC 3 Installation 3.1 Heat Radiation Countermeasures Please refer to the following method for heat radiation countermeasures. Example of heat radiation countermeasures <Hypothetical conditions> (1) Average internal temperature of operation panel: T ≤ 55°C (2) Peripheral temperature of operation panel : Ta ≤ 0°C to 45°C (3) Internal temperature rise value : ΔT = T - Ta (max) = 10°C Procedures for heat design and verification Calculate total heat radiation of each...
  • Page 88 E70 Series Connection Manual 3.1 Heat Radiation Countermeasures The following shows an example of calculation applied to heat radiation countermeasures for the operation panel when 8.4-type display unit is used. Because heat will accumulate in the upper portions of the unit, install an agitating fan as required.
  • Page 89 MITSUBISHI CNC 3 Installation Calculation example of panel internal heating value (1) Calculation of unit heating value Heating value (W) Total heating value of units (W): 28W (= control unit + display unit + keyboard unit + operation panel I/O unit) Total heating value (W) by machine input (D1): 5.6W (=24V (total heating value when the 32 points are simultaneously turned ON) ×...

  • Page 90: Noise Countermeasures

    E70 Series Connection Manual 3.2 Noise Countermeasures 3.2 Noise Countermeasures 3.2.1 Connection of FG (Frame Ground) The frame should basically be grounded at one ground point. Connect the control unit and operation panel I/O unit's 0V (RG) to the FG on the +24V stabilized power supply.

  • Page 91: Shield Clamping Of Cables

    MITSUBISHI CNC 3 Installation 3.2.2 Shield Clamping of Cables The shield cables connected to the units must be properly connected to the ground with clamp fittings and the like in order to stabilize the system's operation while preventing malfunctioning due to exogenous noise. (Refer to "EMC Installation Guidelines: EMC Countermeasure Parts: Shield Clamp Fitting".) 3.2.3 Connecting Spark Killers Connect a spark killer on the coil or the contact in parallel for noise countermeasures.

  • Page 92: Unit Installation

    E70 Series Connection Manual 3.3 Unit Installation 3.3 Unit Installation 3.3.1 Display Unit Mount the display unit with four fixing screws. (Note) Refer to "General Specifications: Display Unit" for the panel cut dimension drawing and the screw hole position. Fixing screws (4)

  • Page 93: Keyboard Unit

    MITSUBISHI CNC 3 Installation 3.3.2 Keyboard Unit Mount the keyboard unit with four fixing screws. (Note 1) Refer to "General Specifications: Keyboard Unit" for the panel cut dimension drawing and the screw hole position. (Note 2) A clear protective film covers the sheet keys of the keyboard at the time of shipment. Make sure to remove the sheet before use.

  • Page 94: Control Unit Battery

    E70 Series Connection Manual 3.3 Unit Installation 3.3.4 Control Unit Battery A lithium battery in the control unit battery holder retains parameter settings, machining programs and the like, which requires to be backed up at the power OFF. Battery Q6BAT Battery cumulative data holding time 45,000 hours (At 0 to 45°C.
  • Page 95 MITSUBISHI CNC 3 Installation...

  • Page 96: Connection

    Connection...

  • Page 97: Precautions For Wiring

    MITSUBISHI CNC 4 Connection 4.1 Precautions for Wiring 4.1.1 Precautions when Connecting/Disconnecting Cables If the cable is connected/disconnected without turning the power OFF, the normal unit or peripheral devices could be damaged, and risks could be imposed. Disconnect each cable with the following procedures. (a) For the following type of connector, press the tabs with a thumb and forefinger in the direction of the arrow, and pull the connector off.
  • Page 98 E70 Series Connection Manual 4.1 Precautions for Wiring (b) For a flat cable type connector with latches, open the latches in the directions of the arrows, and pull the connector off. Open Pull For a flat cable type connector without latches, hold the connector with a thumb and forefinger, and pull the connector off.
  • Page 99 MITSUBISHI CNC 4 Connection (e) For the optical cable connector, pull off while holding down the lock button. Press Pull For the Ethernet connector, pull off while holding down the locked latch. (1) Press Pull CAUTION 1. Do not connect or disconnect the cables between units while the power is ON. 2.

  • Page 100: Precautions For Using Optical Communication Cable

    E70 Series Connection Manual 4.1 Precautions for Wiring 4.1.2 Precautions for Using Optical Communication Cable An optical communication cable is used for communication between the control unit and the drive unit. Special precautions, differing from the conventional cable, are required when laying and handling the optical communication cable.

  • Page 101: Precautions For Laying Optical Communication Cable

    MITSUBISHI CNC 4 Connection 4.1.2.3 Precautions for Laying Optical Communication Cable (1) Do not apply a force exceeding the cable's tolerable tension. Binding the cables too tight with tie-wraps could result in an increased loss or a disconnection. Use a cushioning material such as a sponge or rubber when bundling the cables and fix so that the cables do not move.

  • Page 102: Connection Of Control Unit

    E70 Series Connection Manual 4.2 Connection of Control Unit 4.2 Connection of Control Unit The method for connecting to each unit and device from the control unit is explained in this section. 4.2.1 Control Unit Connection System Drawing Control unit...

  • Page 103: Connecting With Power Supply

    MITSUBISHI CNC 4 Connection 4.2.2 Connecting with Power Supply Connect a general-purpose 24VDC stabilized power supply or PD25 power supply unit to the control unit. (1) When using general-purpose 24VDC stabilized power supply F070 cable DCIN +24V DCIN   (Note 2) DCIN 24VDC Control unit...

  • Page 104: Connecting With Emergency Stop Signal

    E70 Series Connection Manual 4.2 Connection of Control Unit 4.2.3 Connecting with Emergency Stop Signal Connect the emergency stop switch to EMG connector by F120 cable. Emergency stop switch F120 NC control unit Emergency stop switch NC control unit +24V...
  • Page 105 MITSUBISHI CNC 4 Connection <Drive unit (MDS-DJ-V1) external emergency stop: Example 2> NC control unit Stabilized power supply +24V 0V(LG) Emergency MDS-DJ stop switch NC control unit F120 +24V EMGIN MDS-DJ-V1 Emergency stop input circuit <Caution> (1) External emergency stop cannot substitute the emergency stop signal which is input to NC. It is a function which helps the NC emergency stop.

  • Page 106: Connecting With Operation Panel I/O Unit

    E70 Series Connection Manual 4.2 Connection of Control Unit 4.2.4 Connecting with Operation Panel I/O Unit Connect the operation panel I/O unit to the connector CG71. Operation panel Control unit I/O unit CG71 G011 cable CG71 <Related items> Cable drawing: "Cable G011 Cable"...

  • Page 107: Connecting With Drive Unit

    MITSUBISHI CNC 4 Connection 4.2.5 Connecting with Drive Unit Connect the optical communication cables from the NC to the each drive unit so that they run in a straight line from the NC to the drive unit that is a final axis. Up to 6 axes can be connected. Note that the number of connected axes is limited by the NC.

  • Page 108: Connecting With Mds-Dm2 Series

    E70 Series Connection Manual 4.2 Connection of Control Unit 4.2.5.1 Connecting with MDS-DM2 Series CAUTION Connect the NC and the drive units by the optical communication cables. The distance between the NC and the final drive unit must be within 30m and the bending radius within 80mm.

  • Page 109: Connecting With Mds-Dj Series

    MITSUBISHI CNC 4 Connection (2) When using the MDS-DJ unit together MDS-DM2-SPV MDS-DJ-V1 Spindle:1st axis 5th axis Servo:2nd/3rd/4th axis (Final axis) Connected to the NC Optical communication cable The optical communication cables from the NC to the final drive unit must be within 30m. 4.2.5.2 Connecting with MDS-DJ Series CAUTION Connect the NC and the drive units by the optical communication cables.

  • Page 110: Connecting With I/O Devices Via Cc-Link

    E70 Series Connection Manual 4.2 Connection of Control Unit 4.2.6 Connecting with I/O Devices via CC-Link CC-Link unit (FCU7-HN746) works as master station or local station of CC-Link (Ver.2 mode). Mount the CC-Link unit on the control unit's expansion card slot.
  • Page 111 MITSUBISHI CNC 4 Connection Wiring the cables to the CC-Link terminal block (1) Remove the sheath of the cable and isolate each internal wire from the shield mesh. (2) Remove the shield mesh and the coat of each internal wire. Twist the core wires. Shield mesh Approx.

  • Page 112: Connecting With Rs-232C Device

    E70 Series Connection Manual 4.2 Connection of Control Unit 4.2.7 Connecting with RS-232C Device (1) Connect the RS-232C device to the connector SIO. Control unit F035 cable RS-232C device Cable name F034 cable General-purpose cable F035 cable See (2) SD1(TXD1)
  • Page 113 MITSUBISHI CNC 4 Connection (2) Example of wiring connections to the RS-232C device When connecting to the RS-232C device, refer to the following diagrams and cross the wiring for the transmission signals. Hand shaking No hand shaking upon RS/CS, ER/DR signals upon RS/CS, ER/DR signals SD(TXD) SD(TXD)

  • Page 114: Connecting With Skip Signal (Sensor)

    E70 Series Connection Manual 4.2 Connection of Control Unit 4.2.8 Connecting with Skip Signal (Sensor) Connect skip signals to the connector SKIP. Skip signals are used for processing high-speed signals. Always shield the cable. Control unit FCUA-R030 SKIP (Note) Connecting the skip signal cable to a wrong connector causes a damage on the control unit when turning ON the skip signal power supply.
  • Page 115 MITSUBISHI CNC 4 Connection <24V connection at COM terminal> Control unit SKIP R030 cable Stabilized power supply 24VDC(+) 1,5,11,15 24V connection at COM terminal (Note 1) NC recognizes input signals of 2ms or more as the valid skip signals. If machine contacts (relay, etc.) are used, malfunctions will occur due to chattering.

  • Page 116: Connecting With Synchronous Feed Encoder/ Manual Pulse Generator

    E70 Series Connection Manual 4.2 Connection of Control Unit 4.2.9 Connecting with Synchronous Feed Encoder/ Manual Pulse Generator Synchronous feed encoder (1ch) or 5V power supply type manual pulse generator (2ch) can be connected. Synchronous feed encoder OSE1024-3-15-68 R054 cable <Right angle>...

  • Page 117: Connecting With Safety Observing I/O Device

    MITSUBISHI CNC 4 Connection 4.2.10 Connecting with Safety Observing I/O Device Connect safety observing I/O device as the example below. (Below is an example where an MDS-DJ series drive unit is used.) Door open/close check sensor Control unit Drive unit DOOR1 MC_ct1 DC24V...

  • Page 118: Connection Of Operation Panel I/O Unit

    E70 Series Connection Manual 4.3 Connection of Operation Panel I/O Unit 4.3 Connection of Operation Panel I/O Unit 4.3.1 Operation Panel I/O Unit Connection System Drawing Operation panel I/O unit Control unit CG71 G011 cable CG71 R211 cable Remote I/O unit, scan I/O unit card...

  • Page 119: Connecting With Keyboard Unit

    MITSUBISHI CNC 4 Connection 4.3.2 Connecting with Keyboard Unit Connect the keyboard unit to the connector NCKB. The cable comes with the keyboard unit. Operation panel Keyboard unit I/O unit (Rear view) NCKB (Note) Firmly insert the connection cable until it is locked.

  • Page 120: Connecting With Manual Pulse Generator (Mpg)

    E70 Series Connection Manual 4.3 Connection of Operation Panel I/O Unit 4.3.3 Connecting with Manual Pulse Generator (MPG) Both 5V power supply type (UFO-01-2Z9) and 12V power supply type (HD60C) manual pulse generator can be used. Take the maximum cable length, etc. into consideration when selecting.

  • Page 121: Handle Numbers

    MITSUBISHI CNC 4 Connection 4.3.3.1 Handle Numbers Unit configuration decides handle Nos. "ENC": Connector on control unit "MPG": Connector on operation panel I/O unit Operation panel I/O unit (FCU7-DX71x/ DX72x/ DX73x/DX621) 1st handle 2nd handle 3rd handle Used "MPG" 1ch "MPG"...

  • Page 122: Wiring For 24V Common Input

    E70 Series Connection Manual 4.3 Connection of Operation Panel I/O Unit 4.3.4.1 Wiring for 24V Common Input For connection details, refer to the descriptions on machine input connector pin assignment in "(1) (Machine side) CG31/CG33/CG35 Machine input (CG31)", "(2) Machine input (CG33)", and "(3) Machine input (CG35)"...

  • Page 123: Wiring For Source Type Output (Fcu7-Dx621/Dx711/Dx721/Dx731)

    MITSUBISHI CNC 4 Connection 4.3.4.3 Wiring for Source Type Output (FCU7-DX621/DX711/DX721/DX731) Operation panel I/O unit (Card name : HN331/HN351/HN371/HN372) Machine side CG32 (CG34,CG36) *1 Additional wiring 24VDC 24VDC 24VDC 24VDC 24VDC 24VDC 24VDC Y200 Y201 Y202 Y203 Y204 Y205 Y206 Y207 Y208 Y209...

  • Page 124: Outline Of Analog Signal Output Circuit

    E70 Series Connection Manual 4.3 Connection of Operation Panel I/O Unit 4.3.4.4 Outline of Analog Signal Output Circuit Operation Panel I/O unit The analog signal output circuit can be used only for the FCU7-DX621/DX721.

  • Page 125: Connection Of Remote I/O Unit

    MITSUBISHI CNC 4 Connection 4.4 Connection of Remote I/O Unit This chapter describes the connection of the remote I/O unit and machine control signals. 4.4.1 Connection and Station No. Setting on Remote I/O Unit When connecting directly to the control unit Control unit Remote I/O unit FCUA-DX1x1...
  • Page 126 E70 Series Connection Manual 4.4 Connection of Remote I/O Unit When connecting to the operation panel I/O unit Control unit Remote I/O unit Operation panel I/O unit FCUA-DX1x1 FCU7-DX711 Occupies Station No.3 - 6 the station No. 1, 2, 7, 8...

  • Page 127: Station No. Setting When Using Multiple Remote I/O Units

    MITSUBISHI CNC 4 Connection 4.4.2 Station No. Setting when Using Multiple Remote I/O Units Multiple remote I/O units can be used, as long as the total No. of occupied stations connected with serial links is eight or less. (three/four or less when connected to the operation panel I/O unit). Unit type Number of occupied stations FCUA-DX101...
  • Page 128 E70 Series Connection Manual 4.4 Connection of Remote I/O Unit Setting example 3 FCUA-DX111 FCUA-DX121 ＋ ＋ ＋ ＋ Number of occupied stations: 2 Total number of occupied stations: 8 (Maximum configuration)
  • Page 129 MITSUBISHI CNC 4 Connection When connecting to the operation panel I/O unit Station No. 1, 2, 7, 8 (or 1, 2, 3, 7, 8) are occupied by the operation panel I/O unit. (Station No. 7 and 8 are reserved for manual pulse generator.) The maximum numbers of stations and I/O points assigned to remote I/O unit(s) via RIO3 are as follows.
  • Page 130 E70 Series Connection Manual 4.4 Connection of Remote I/O Unit Setting example 3 FCUA-DX111 FCU7-DX621/721/731 FCUA-DX101 FCUA-DX121 ＋ ＋ Number of occupied stations: 1 Total number of occupied stations: 3 (Maximum configuration)

  • Page 131: Connecting Fcua-Dx101/141 Unit With Machine Control Signal

    MITSUBISHI CNC 4 Connection 4.4.3 Connecting FCUA-DX101/141 Unit with Machine Control Signal Input Output Type of machine input/output signal and number of points 32 points 32 points FCUA-R300 / FCUA-DX101 FCUA-R301 DI-L FCUA-DX141 Machine signal FCUA-R300 / FCUA-R301 DO-L Machine signal <Outline of connection>...
  • Page 132 E70 Series Connection Manual 4.4 Connection of Remote I/O Unit <Signal assignment> FCUA-DX101/141 <CAUTION> Machine side DI-L When using two or more remote I/O units or control panel, etc. when connecting to the operation panel I/O unit, the signal assignment will differ. Refer to the "PLC Interface Manual"...

  • Page 133: Connecting Fcua-Dx141 Unit With Analog Input/Output Signal

    MITSUBISHI CNC 4 Connection 4.4.4 Connecting FCUA-DX141 Unit with Analog Input/Output Signal For the analog input/output signal, connect the FCUA-R031 cable to "AIO". Up to four input points and one output point can be connected for the analog input/output signal. When manufacturing the FCUA-R031 cable, use the FCUA-CS000 connector set (optional, with both ends).

  • Page 134: Connecting Fcua-Dx111 Unit With Machine Control Signal

    E70 Series Connection Manual 4.4 Connection of Remote I/O Unit 4.4.5 Connecting FCUA-DX111 Unit with Machine Control Signal Input Output Type of machine input/output signal and number of points 64 points 48 points FCUA-DX111 FCUA-R300 / FCUA-R301 DI-L Machine signal...
  • Page 135 MITSUBISHI CNC 4 Connection <Signal assignment> <CAUTION> When using two or more remote I/O units or when FCUA-DX111 connecting to the operation panel I/O unit, the DI-L DI-R signal assignment will differ. Refer to the "PLC Interface Manual" for details. The I/O assignment shows an example when the station No.

  • Page 136: Connecting Fcua-Dx121 Unit With Machine Control Signal

    E70 Series Connection Manual 4.4 Connection of Remote I/O Unit 4.4.6 Connecting FCUA-DX121 Unit with Machine Control Signal Analog Input Output Type of machine input/output signal and output number of points 64 points 48 points 1 point FCUA-DX121 FCUA-R300 /...
  • Page 137 MITSUBISHI CNC 4 Connection <Signal assignment> <CAUTION> When using two or more remote I/O units or when FCUA-DX121 connecting to the operation panel I/O unit, the signal assignment will differ. Refer to the "PLC Interface DI-L DI-R Manual" for details. The I/O assignment shows an example when the station No.

  • Page 138: Connection Of Mitsubishi Cnc Machine Operation Panel

    E70 Series Connection Manual 4.5 Connection of MITSUBISHI CNC Machine Operation Panel 4.5 Connection of MITSUBISHI CNC Machine Operation Panel Connect MITSUBISHI CNC Machine operation panel A to the remote I/O unit I/F of control unit or operation panel I/O unit.
  • Page 139 MITSUBISHI CNC 4 Connection <Software Interface> MITSUBISHI CNC Machine operation panel occupies RIO station No. 4 to 6. The device numbers for switch and LED on operation panel are fixed as listed below. The following lists the devices for using the RIO 1st channel. Device No.
  • Page 140 E70 Series Connection Manual 4.5 Connection of MITSUBISHI CNC Machine Operation Panel (2) MITSUBISHI CNC Machine operation panel A (Key switch/LED) MITSUBISHI CNC Machine operation panel A is equipped with 55 switches and 55 LEDs. They are allocated X device and Y device as in the figure below.
  • Page 141 MITSUBISHI CNC 4 Connection...

  • Page 142: Appendix 1 Cable

    Appendix 1 章 付録 Cable...
  • Page 143 MITSUBISHI CNC Appendix 1 Cable (Note) Symbols for writing cable drawings indicates twisted pair. indicates the shield sheath. indicates shield clamping to the grounding plate. (4) In the cable drawings, the partner of the twisted pair cable is given a priority, so the pin No. of the connectors at both ends are not necessary in number of order.

  • Page 144: Appendix 1.1 Cable Wire And Assembly

    E70 Series Connection Manual Appendix 1.1 Cable Wire and Assembly Appendix 1.1 Cable Wire and Assembly (1) Cable wire The specifications of the wire used for each cable, and the machining methods are shown in this section. When manufacturing the detector cable and battery connection cable, use the recommended wires shown below or equivalent products.
  • Page 145 MITSUBISHI CNC Appendix 1 Cable (2) Cable assembly Assemble the cable with the cable shield wire securely connected to the ground plate of the connector. Core wire Connect with a ground plate of connector. Shield Sheath (external conductor)

  • Page 146: Appendix 1.2 Cnp2E-1 Cable

    E70 Series Connection Manual Appendix 1.2 CNP2E-1 Cable Appendix 1.2 CNP2E-1 Cable Max. cable length: 30m Application: Motor side PLG cable Spindle side accuracy detector TS5690 cable Spindle drive unit side connector (3M) Spindle motor side connector   Receptacle: 36210-0100PL...

  • Page 147: Appendix 1.3 Cnp3Ez-2P/Cnp3Ez-3P Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.3 CNP3EZ-2P/CNP3EZ-3P Cable Max. cable length: 30m Application: Spindle side detector cable OSE-1024 cable CNP3EZ-2P (Straight) CNP3EZ-3P (Angle) Spindle drive unit side connector Spindle motor side connector (3M)   (DDK) Receptacle: 36210-0100PL Connector: MS3106A20-29S (D190) Shell kit: 36310-3200-008 Back shell: CE02-20BS-S (straight) (MOLEX)

  • Page 148: Appendix 1.4 Cnv22J-K1P / Cnv22J-K2P Cable

    E70 Series Connection Manual Appendix 1.4 CNV22J-K1P / CNV22J-K2P Cable Appendix 1.4 CNV22J-K1P / CNV22J-K2P Cable Max. cable length: 0.3m Application: For HF-KP (Servo) Motor side detector relay cable (motor side) Compatible with only IP65 CNV22J-K1P (load side angle) CNV22J-K2P (reverse load side angle)

  • Page 149: Appendix 1.5 Cnv2E-8P/Cnv2E-9P Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.5 CNV2E-8P/CNV2E-9P Cable Max. cable length: 30m Application: For HF/HF-H, HF-KP (Tool spindle) Motor side detector cable (for A48/A51/A74N(/A74)) / For HF-KP (Servo) Motor side detector relay cable (Drive unit side) (CNV2E-8P) CNV2E-8P (Straight) CNV2E-9P (Angle) Motor detector/ Drive unit side connector...

  • Page 150: Appendix 1.6 Cnv2E-Hp Cable

    E70 Series Connection Manual Appendix 1.6 CNV2E-HP Cable Appendix 1.6 CNV2E-HP Cable Max. cable length: 30m Application: MDS-B-HR unit cable Drive unit side connector (3M) MDS-B-HR unit side connector Receptacle: 36210-0100PL (Hirose Electric) Shell kit: 36310-3200-008 (MOLEX) Plug: RM15WTP-8S Connector set: 54599-1019 Clamp: RM15WTP-CP (10) 0.5mm...

  • Page 151: Appendix 1.7 Cnv2E-K1P / Cnv2E-K2P Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.7 CNV2E-K1P / CNV2E-K2P Cable Max. cable length: 10m Application: For HF-KP (Servo) Motor side detector cable Compatible with only IP65 CNV2E-K1P (load side angle) CNV2E-K2P (reverse load side angle) Servo drive unit side connector Servo motor detector connector (3M) (Tyco Electronics AMP)

  • Page 152: Appendix 1.8 Dg21 Cable

    E70 Series Connection Manual Appendix 1.8 DG21 Cable Appendix 1.8 DG21 Cable Max. cable length: 5m Application: Battery cable (For drive unit - battery unit) Drive unit side connector Battery unit side connector (Hirose Electric) (3M)   Connector: DF1B-2S-2.5R Connector: 10120-3000VE...

  • Page 153: Appendix 1.9 Dg22 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.9 DG22 Cable Max. cable length: 10m Application: Battery cable (For drive unit - drive unit) (Note) This cable is required to supply the power from the battery unit to multiple drive units. Drive unit side connector Drive unit side connector (Hirose Electric) (Hirose Electric)

  • Page 154: Appendix 1.10 Dg23 Cable

    E70 Series Connection Manual Appendix 1.10 DG23 Cable Appendix 1.10 DG23 Cable Max. cable length: 10m Application: Battery cable (For drive unit - battery box) (Note) The battery box side is connected using a bare conductor or a terminal bar.

  • Page 155: Appendix 1.11 Dg24 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.11 DG24 Cable Max. cable length: 10m Application: 5V spply/DO output cable (For drive unit - battery box) (Note) The battery box side is connected using a bare conductor or a terminal bar. Drive unit side connector Battery box side Connector :10120-3000VE...

  • Page 156: Appendix 1.12 Dg25 Cable

    E70 Series Connection Manual Appendix 1.12 DG25 Cable Appendix 1.12 DG25 Cable Max. cable length: 10m Application: Battery cable (For drive unit - battery box) Drive unit side connector Battery box side (Hirose Electric) Connector : DF3-2S-2C Contact : DF3-2428SCC 0.2mm...

  • Page 157: Appendix 1.13 F023/F024 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.13 F023/F024 Cable Max. cable length: 20m Application: Manual Pulse Generator (5V spec) HANDLE HANDLE HA1A HA1B HA2A HA2B [HANDLE] Wire material: UL1061-2464 [1ch][2ch] Connector: 10120-3000VE AWG22×6P Crimp terminal: V1.25-3 Case: 10320-52F0-008 Recommended manufacturer: Oki Recommended manufacturer: JST Recommended manufacturer: 3M Electric Cable...

  • Page 158: Appendix 1.14 F034/F035 Cable

    E70 Series Connection Manual Appendix 1.14 F034/F035 Cable Appendix 1.14 F034/F035 Cable Max. cable length: 15m (the maximum length of the cable when connected to the control unit via other units) Application: RS232C I/F cable (for control unit) SD1(TXD1) RD1(RXD1)

  • Page 159: Appendix 1.15 F070 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.15 F070 Cable Max. cable length: 30m Application: 24VDC power cable DCIN DCIN +24V +24V [DCIN] Connector: 2-178288-3 Wire material: B-18(19)U×2SJ-1×9 Crimp terminal: V1.25-3 or V1.25-4×2 Contact: 1-175218-5 ×3 Recommended manufacturer: Recommended manufacturer: JST Recommended manufacturer: Tyco Sumitomo Electric Industries Electronics...

  • Page 160: Appendix 1.16 F110 Cable

    E70 Series Connection Manual Appendix 1.16 F110 Cable Appendix 1.16 F110 Cable Max. cable length: 15m Application: 24VDC power cable for PD25/PD27 DCIN DCOUT CF01 DCOUT DCIN AWG16 +24V +24V CF01 AWG22 ACFAIL ACFAIL [DCIN] Connector: 2-178288-3 [DCOUT] Contact: 1-175218-5 ×3...

  • Page 161: Appendix 1.17 F120 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.17 F120 Cable Max. cable length: 30m Application: Emergency stop cable B22-9 EMG IN EMG IN [EMG] Wire material: B-22(19)U×2SJ-1×9 Connector: 005057-9403 Crimp terminal: V1.25-3 ×2 Recommended manufacturer: Contact: 0016020103 ×3 Recommended manufacturer: JST Sumitomo Electric Industries Recommended manufacturer: MOLEX...

  • Page 162: Appendix 1.18 F170 Cable

    E70 Series Connection Manual Appendix 1.18 F170 Cable Appendix 1.18 F170 Cable Max. cable length: 15m Application: ON/OFF switch cable for PD25/PD27 ON/OFF PD25 ON/OFF OFF-1 P-OFF OFF-2 ON-1 ON-2 P-ON [ON/OFF] Connector: 1-178288-5 Wire material: DPVVSB 3P×0.3mm Crimp terminal: V1.25-3 or V1.25-4...

  • Page 163: Appendix 1.19 F221 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.19 F221 Cable Max. cable length: 30m Application: Analog output [AO] Wire material: B-22(19)×2SJ-1×9 Connector: 10120-3000VE Crimp terminal: V1.25-3 Recommended manufacturer: Contact: 10320-52F0-008 Recommended manufacturer: JST Sumitomo Electric Industries Recommended manufacturer: 3M (Note 1) Follow the instruction of the machine side in connecting the shield. Do not connect on the base I/O unit side.

  • Page 164: Appendix 1.20 F320/F321 Cable

    E70 Series Connection Manual Appendix 1.20 F320/F321 Cable Appendix 1.20 F320/F321 Cable Max. cable length: 50m Application: Manual Pulse Generator (12V spec) HANDLE HANDLE HA1A HA1B HA2A HA2B [HANDLE] Wire material: UL1061-2464 [1ch][2ch] Connector: 10120-3000VE AWG22×6P Crimp terminal: V1.25-3 Case: 10320-52F0-008...

  • Page 165: Appendix 1.21 F351 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.21 F351 Cable Max. cable length: 50m Application: DI/DO CG31,CG32,CG33,CG34,CG35,CG36 [CG31, CG32, CG33, CG34, CG35, CG36] Wire material: B40-S Connector: 7940-6500SC Recommended manufacturer: Strain relief: 3448-7940 Oki Electric Cable Recommended manufacturer: 3M (Note) This cable is used to connect the operation panel I/O unit. Select FCUA-R300, which doesn’t have strain relief, when connecting to remote I/O unit.

  • Page 166: Appendix 1.22 Fcua-R030 Cable

    E70 Series Connection Manual Appendix 1.22 FCUA-R030 Cable Appendix 1.22 FCUA-R030 Cable Max. cable length: 20m Application: SKIP input cable SKIP SKIP SKIP0 SKIP0 SKIP1 SKIP1 SKIP2 SKIP2 SKIP3 SKIP3 SKIP4 SKIP4 SKIP5 SKIP5 SKIP6 SKIP6 SKIP7 SKIP7 [SKIP] Wire material: UL1061-2464 Connector: 10120-3000VE AWG22×6P...

  • Page 167: Appendix 1.23 Fcua-R031 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.23 FCUA-R031 Cable Max. cable length: 30m Application: Analog input/output (for remote I/O unit) [AIO] Wire material: UL1061-2464 Connector: 10120-3000VE AWG24×6P Crimp terminal: V1.25-3 ×10 Case: 10320-52F0-008 Recommended manufacturer: Recommended manufacturer: JST Recommended manufacturer: 3M Oki Electric Cable (Note) Fold the cable shield over the sheath, and wrap copper foil tape over it.

  • Page 168: Appendix 1.24 Fcua-R050/R054 Cable

    E70 Series Connection Manual Appendix 1.24 FCUA-R050/R054 Cable Appendix 1.24 FCUA-R050/R054 Cable Max. cable length: 30m Application: Synchronous encoder - control unit FCUA-R050 FCUA-R054 ENC1 ENC1A (ENC2A) ENC1A*(ENC2A*) ENC1B (ENC2B) ENC1B*(ENC2B*) ENC1Z (ENC2Z) ENC1Z*(ENC2Z*) [FCUA-R050 cable] Connector: MS3106B20-29S Cable clamp: MS3057-12A...

  • Page 169: Appendix 1.25 Fcua-R211 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.25 FCUA-R211 Cable Max. cable length: 30m (the maximum length of the cable when connected to the control unit via other units) Application: Remote I/O (with terminal block) between remote I/O, remote I/O-CNC control unit, remote I/O-Operation panel I/O unit, remote I/O-MITSUBISHI CNC machine operation panel A RIO1,RIO2,RIO3(FCUA-R211)

  • Page 170: Appendix 1.26 Fcua-R300/Fcua-R301 Cable

    E70 Series Connection Manual Appendix 1.26 FCUA-R300/FCUA-R301 Cable Appendix 1.26 FCUA-R300/FCUA-R301 Cable Type: FCUA-R300 Max. cable length: 50m Application: DI/DO cable (one side connector) (for remote I/O unit) DI-L/DO-L, DI-R/DO-R [DI-L/DO-L,DI-R/DO-R] Wire material: B40-S Connector: 7940-6500SC Recommended manufacturer: Recommended manufacturer: 3M...
  • Page 171 MITSUBISHI CNC Appendix 1 Cable Machine control panel, electric cabinet, etc. FCUA-R300 FCUA-R301 RA : Relay PL : Pilot lamp Connector pin correspondence Terminal FCUA- Terminal FCUA- block BX1F DX1xx block BX1F DX1xx...

  • Page 172: Appendix 1.27 G011 Cable

    E70 Series Connection Manual Appendix 1.27 G011 Cable Appendix 1.27 G011 Cable Max. cable length: 0.5m Application: Connection between NC unit and operation panel I/O unit G011 3.3V KBCS0* KBCS1* KBCS2* KBAD0 KBAD1 KBAD2 KBD0 KBD1 KBD2 KBD3 KBRES* RDYOUT* BUZOUT* 3.3V...

  • Page 173: Appendix 1.28 G023/G024 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.28 G023/G024 Cable Max. cable length: 20m (the maximum length of the cable when connected to the control unit via other units) Application: Manual Pulse Generator cable (5V) (for connection to control unit) HA1A HA1B HA2A HA2B...

  • Page 174: Appendix 1.29 G071 Cable

    E70 Series Connection Manual Appendix 1.29 G071 Cable Appendix 1.29 G071 Cable Max. cable length: 0.5m Application: 24VDC relay cable for MITSUBISHI CNC machine operation panel DCOUT DCIN R : Red W : White G : Green [DCOUT] [DCIN] Connector: 2-178288-3...

  • Page 175: Appendix 1.30 G300 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.30 G300 Cable Max. cable length: 10m Application: LAN cross cable (Shielded cable is recommended when the length will be 1m or more) G300 White White Green Green Green Green White White Orange Orange Orange Orange Blue...

  • Page 176: Appendix 1.31 G301 Cable

    E70 Series Connection Manual Appendix 1.31 G301 Cable Appendix 1.31 G301 Cable Max. cable length: 1m Application: LAN straight cable (Shielded cable is recommended when the length will be 1m or more) G301 White White Green Green Green Green White...

  • Page 177: Appendix 1.32 G380 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.32 G380 Cable Max. cable length: 30m Application: Optical communication cable for wiring between drive units (outside panel) for optical communication repeater unit Use when the cable length is 10m or more to 30m or less. Section with reinforced sheath Section without reinforced sheath...

  • Page 178: Appendix 1.33 G395 Cable

    E70 Series Connection Manual Appendix 1.33 G395 Cable Appendix 1.33 G395 Cable Max. cable length: 10m Application: Optical communication cable for wiring between drive units (outside panel) for wiring between NC-drive units Use when wiring outside of the panel with a cable of 10m or less.

  • Page 179: Appendix 1.34 G396 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.34 G396 Cable Max. cable length: 10m Application: Optical communication cable for wiring between drive units (inside panel) Use when wiring in the panel with a cable of 10m or less. [OPT] Wire material: ESCA Premium Connector: PF-2D103 Recommended manufacturer: Recommended manufacturer:...

  • Page 180: Appendix 1.35 G460 Cable

    E70 Series Connection Manual Appendix 1.35 G460 Cable Appendix 1.35 G460 Cable Max. cable length: 0.5m Application: Cable between MITSUBISHI CNC machine operation panel A and MITSUBISHI CNC machine operation panel B RSW1 SUBP RSW2 SW-NO SW-NO SW-C SW-C [RSW1][RSW2]...

  • Page 181: Appendix 1.36 Mr-Bks1Cbl-A1-H / Mr-Bks1Cbl-A2-H Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.36 MR-BKS1CBL-A1-H / MR-BKS1CBL-A2-H Cable Max. cable length: 10m Application: <200V Series> Brake cable for HF-KP MR-BKS1CBL-A1-H (load side angle) MR-BKS1CBL-A2-H (reverse load side angle) Servo motor brake connector (Japan Aviation Electronics) Connector: JN4FT02SJ1 Hood, Socket insulator, Bushing and Ground nut Contact:...

  • Page 182: Appendix 1.37 Mr-Pws1Cbl-A1-H / Mr-Pws1Cbl-A2-H Cable

    E70 Series Connection Manual Appendix 1.37 MR-PWS1CBL-A1-H / MR-PWS1CBL-A2-H Cable Appendix 1.37 MR-PWS1CBL-A1-H / MR-PWS1CBL-A2-H Cable Max. cable length: 10m Application: <200V Series> Power cable for HF-KP MR-PWS1CBL-A1-H (load side angle) MR-PWS1CBL-A2-H (reverse load side angle) Servo motor power supply connector...

  • Page 183: Appendix 1.38 R-Tm Terminator Connector

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.38 R-TM Terminator Connector Application: Terminator for OPI interface R-TM R-TM TXRX* TXRX [R-TM] Connector: 1-178288-3 (X type) Contact: 1-175216-2 ×2 Recommended manufacturer: Tyco Electronics Resistor: 100Ω 1/4W (Note 1) The parts used shall be Mitsubishi recommended parts. Equivalent parts may be used providing they are compatible with the specifications.

  • Page 184: Appendix 1.39 Sh21 Cable

    E70 Series Connection Manual Appendix 1.39 SH21 Cable Appendix 1.39 SH21 Cable Max. cable length: 30m Application: Power supply communication cable Power backup unit communication cable Cable for Auxiliary axis/Servo drive units SV1, SV2 SVTXD SVTXD SVTXD* SVTXD* SVALM SVALM...

  • Page 185: Appendix 1.40 Sh41 Cable

    MITSUBISHI CNC Appendix 1 Cable Appendix 1.40 SH41 Cable Max. cable length: 1m (the maximum length of the cable when connected to the control unit via other units) Application: Remote I/O cable between remote I/O, remote I/O-CNC control unit, remote I/O-Operation panel I/O unit, remote I/O-MITSUBISHI CNC machine operation panel A (between remote I/O units in a panel) RIO1,RIO3(CSH41)

  • Page 186: Appendix 1.41 List Of Cable Connector Sets

    E70 Series Connection Manual Appendix 1.41 List of Cable Connector Sets Appendix 1.41 List of Cable Connector Sets Type Application Package contents Connector (3M) Shell kit (3M) 10120-3000VE x 2pcs. 10320-52F0-008 x 2pcs. FCUA-CS000 Control unit - General I/O units...
  • Page 187 MITSUBISHI CNC Appendix 1 Cable...

  • Page 188: Appendix 2 Emc Installation Guidelines

    Appendix 2 章 付録 EMC Installation Guidelines...

  • Page 189: Appendix 2.1 Introduction

    MITSUBISHI CNC Appendix 2 EMC Installation Guidelines For details of the drive section (servo/spindle drive unit), refer to the "EMC Installation Guidelines" of instruction manuals for each drive unit. Appendix 2.1 Introduction EMC Directives became mandatory as of January 1, 1996. The subject products must have a CE mark attached indicating that the product complies with the Directives.

  • Page 190: Appendix 2.3 Emc Measures

    E70 Series Connection Manual Appendix 2.3 EMC Measures Appendix 2.3 EMC Measures The main items relating to EMC measures include the following. (1) Store the device in a sealed metal panel. (2) Ground all conductors that are floating electrically. Decrease the impedance.

  • Page 191: Appendix 2.4.2 Measures For Door

    MITSUBISHI CNC Appendix 2 EMC Installation Guidelines Appendix 2.4.2 Measures for Door (1) Use metal for all members configuring the panel. (2) When joining the door, use a gasket to lower the impedance of the contacting sections, or use a structure with a large contact area as shown below.

  • Page 192: Appendix 2.5 Measures For Wiring In Panel

    E70 Series Connection Manual Appendix 2.5 Measures for Wiring in Panel Appendix 2.5 Measures for Wiring in Panel Cables act as antennas to propagate unnecessary noise, and thus must be appropriately shielded and treated. The following measures must be sufficiently considered for the cables (SH21/G018/F012/FCUA-R211) that carry out high-speed communication.

  • Page 193: Appendix 2.5.2 Shield Treatment Of Cables

    MITSUBISHI CNC Appendix 2 EMC Installation Guidelines Appendix 2.5.2 Shield Treatment of Cables Use shielded cables for the cables wired outside the panel. Use a shield clamp within 10cm of the lead-out port from the panel. (Refer to "EMC Countermeasure Parts: Shield Clamp Fitting".) (1) DC power supply cable [F110/F070 cable] Shield clamp...
  • Page 194 E70 Series Connection Manual Appendix 2.5 Measures for Wiring in Panel (3) Servo communication cable [SH21 cable] Shield clamp Control panel Control panel Control unit Drive section unit SH21B cable Ferrite core Use a shield clamp within 10cm from the panel's inlet/outlet.

  • Page 195: Appendix 2.6 Emc Countermeasure Parts

    MITSUBISHI CNC Appendix 2 EMC Installation Guidelines Appendix 2.6 EMC Countermeasure Parts Appendix 2.6.1 Shield Clamp Fitting The effect can be improved by directly connecting the cable's shield sheath to the grounding plate as shown below. Install the grounding plate near the outlet (within 10cm) of each panel, and press against the grounding plate with the clamp fitting.

  • Page 196: Appendix 2.6.2 Ferrite Core

    E70 Series Connection Manual Appendix 2.6 EMC Countermeasure Parts Appendix 2.6.2 Ferrite Core The ferrite core is mounted integrally with the plastic case. This can be installed with one touch without cutting the interface cable or power supply cable. This ferrite core is effective against common mode noise, allowing measures against noise without affecting the quality of the signal.

  • Page 197: Appendix 2.6.3 Surge Absorber

    MITSUBISHI CNC Appendix 2 EMC Installation Guidelines Appendix 2.6.3 Surge Absorber Make sure that the surge does not directly enter the AC line of the general-purpose stabilized power supply (user- prepared) supplying power to the control unit and DIO. Select the following product or equivalent for the surge absorber. Refer to the manufacturer catalog for detailed characteristics, outline and connection methods of the surge absorber.
  • Page 198 E70 Series Connection Manual Appendix 2.6 EMC Countermeasure Parts (3) Example of surge absorber installation An example of installing the surge absorber in the machine control panel is shown below. A short-circuit fault will occur in the surge absorber if a surge exceeding the tolerance is applied. Thus, install a circuit protection breaker in the stage before the surge absorber.

  • Page 199: Appendix 2.6.4 Selection Of Stabilized Power Supply

    MITSUBISHI CNC Appendix 2 EMC Installation Guidelines Appendix 2.6.4 Selection of Stabilized Power Supply Consider the following characteristics when selecting the stabilized power supply (prepared by machine manufacturer). Use a power supply that complies with CE Marking or that follows the safety standards given below. Stabilized power supply selection items Item Standard setting...

  • Page 200: Appendix 3 Restrictions For Lithium Batteries

    Appendix 3 章 付録 Restrictions for Lithium Batteries...

  • Page 201: Appendix 3.1 Restriction For Packing

    MITSUBISHI CNC Appendix 3 Restrictions for Lithium Batteries Appendix 3.1 Restriction for Packing The United Nations Dangerous Goods Regulations "Article 12" became effective from 2003. When transporting lithium batteries with means subject to the UN Regulations, such as by air transport, measures corresponding to the Regulations must be taken.

  • Page 202: Appendix 3.1.1 Target Products

    E70 Series Connection Manual Appendix 3.1 Restriction for Packing Appendix 3.1.1 Target Products The following Mitsubishi NC products use lithium batteries. If the lithium metal content exceeds 1g for battery cell and 2g for battery, the battery is classified as dangerous good (Class9).

  • Page 203: Appendix 3.1.2 Handling By User

    MITSUBISHI CNC Appendix 3 Restrictions for Lithium Batteries Appendix 3.1.2 Handling by User The following technical opinion is solely Mitsubishi's opinion. The shipper must confirm the latest IATA Dangerous Goods Regulations, IMDG Codes and laws and orders of the corresponding export country. These should be checked by the company commissioned for the actual transportation.

  • Page 204: Appendix 3.1.3 Reference

    E70 Series Connection Manual Appendix 3.1 Restriction for Packing (2) When packaged by user The user must follow UN Regulations when packing, preparing for shipping and preparing the indications, etc. (a) Packing a lithium battery falling under Class 9 Consult with The Ship Equipment Inspection Society of Japan for details on packaging.

  • Page 205: Appendix 3.2 Products Information Data Sheet (Er Battery)

    MITSUBISHI CNC Appendix 3 Restrictions for Lithium Batteries Appendix 3.2 Products information data sheet (ER battery) MSDS system does not cover the product used in enclosed state. The ER battery described in this section applies to that product. This description is applied to the normal use, and is provided as reference but not as guarantee. This description is based on the lithium battery's (ER battery) hazardous goods data sheet (Products information data sheet) which MITSUBISHI has researched, and will be applied only to the ER batteries described in the previous section "Restriction for Packing".
  • Page 206 E70 Series Connection Manual Appendix 3.2 Products information data sheet (ER battery) (7) Stability and reactivity Stability Stable under normal handling condition. Do not mix multiple batteries with their terminals uninsulated. This may cause a short- Condition to avoid circuit, resulting in heating, bursting or ignition.

  • Page 207: Appendix 3.3 Issuing Domestic Law Of The United States For Primary Lithium Battery Transportation

    MITSUBISHI CNC Appendix 3 Restrictions for Lithium Batteries Appendix 3.3 Issuing Domestic Law of the United States for Primary Lithium Battery Transportation Federal Aviation Administration (FAA) and Research and Special Programs Administration (RSPA) announced an additional regulation (interim final rule) for the primary lithium batteries transportation restrictions item in "Federal Register" on Dec.15 2004.

  • Page 208: Appendix 3.4 Restriction Related To Eu Battery Directive

    This symbol mark is according to the directive 2006/66/EC Article 20 Information for end-users and Annex II. Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and/or reused. This symbol means that batteries and accumulators, at their end-of-life, should be disposed of separately from your household waste.
  • Page 209 MITSUBISHI CNC Appendix 3 Restrictions for Lithium Batteries...

  • Page 210: Appendix 4 Precautions For Compliance To Ul/C-Ul Standards

    Appendix 4 章 付録 Precautions for Compliance to UL/c-UL Standards...
  • Page 211 MITSUBISHI CNC Appendix 4 Precautions for Compliance to UL/c-UL Standards Observe the following matters to comply with UL/c-UL Standards. Refer to "Instruction Manual for Compliance with UL/c-UL Standard"(BNP-B2429-002) for details. (1) Selection of external 24VDC power supply unit (The unit shall be prepared by the machine tool builder.) This NC system complies with the UL Standards on the condition that the stabilized power supply unit supplying 24VDC to each unit is a UL-approved part.
  • Page 212 Revision History Date of Manual No. Revision details revision Dec. 2012 IB(NA)1501151-A First edition created. The construction of chapters and sections were revised. - "5 EMC Installation Guidelines" to Appendix 2. - "6 Restrictions for Lithium Batteries" to Appendix 3. Dec.
  • Page 213 Global Service Network AMERICA EUROPE MITSUBISHI ELECTRIC AUTOMATION INC. (AMERICA FA CENTER) MITSUBISHI ELECTRIC EUROPE B.V. Central Region Service Center GOTHAER STRASSE 10, 40880 RATINGEN, GERMANY 500 CORPORATE WOODS PARKWAY, VERNON HILLS, ILLINOIS 60061, U.S.A. TEL: +49-2102-486-0 / FAX: +49-2102-486-5910...
  • Page 214 MITSUBISHI ELECTRIC AUTOMATION (CHINA) LTD. (CHINA FA CENTER) Singapore Service Center China (Shanghai) Service Center 307 ALEXANDRA ROAD #05-01/02 MITSUBISHI ELECTRIC BUILDING SINGAPORE 159943 1-3,5-10,18-23/F, NO.1386 HONG QIAO ROAD, CHANG NING QU, TEL: +65-6473-2308 / FAX: +65-6476-7439 SHANGHAI 200336, CHINA...
  • Page 215 Every effort has been made to keep up with software and hardware revisions in the contents described in this manual. However, please understand that in some unavoidable cases simultaneous revision is not possible. Please contact your Mitsubishi Electric dealer with any questions or comments regarding the use of this product. Duplication Prohibited This manual may not be reproduced in any form, in part or in whole, without written permission from Mitsubishi Electric Corporation.

Table of Contents