TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 1 Safety Precautions 1.1. General Guide Lines 1. It is advisable to insert an isolation transformer in the AC supply before servicing a hot chassis. 2. When servicing, observe the original lead dress, especially the lead dress in the high voltage circuits.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 3 Disassembly for Service This flowchart indicates disassembly items of the cabinet parts and circuit boards in order to find the items necessary for servicing, when reassembling, perform the procedures in the reverse order.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ Note: Board ground wires may have to be disconnected to disassemble some boards. All ground wires must be reconnected using jumper leads if necessary before power is applied to Receiver for service.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 3.9. Rear Cover (Bottom) 3.10. Disassembly For CRT Removal 1. Remove (16) screws. To facilitate CRT replacement, the complete CRT mounting chassis does not need to be removed.
Page 11
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 7. Release CRT anode lead from CRT chassis wire clamp and all other wires from holders. 8. Wire the anode lead wire. 9. Lift out CRT assembly with lens assembly and other CRT neck assemblies.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 4 Service Hints 4.1. Service position for Main 4.3. Service Position for K-Board chassis 1. Remove the Speaker Grille. 2. Remove the K-Board by (4) screws. 1. Remove the Rear Cover (Bottom) by removing (16) screws and (1) screws around its perimeter.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 4.5. Service Position for G-Board 1. Remove the Speaker Grille. 2. Remove the Terminal Door by (4) screws. 3. Remove the G-Board by (2) screws.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 5 Self Check 1. Self-Check is used to automatically check the bus lines and hexadecimal code of the TV set. 2. To get into the Self -Check mode press the down (...
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 6 Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Mode.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 7 CRT Set Up Caution: 7.2. Electrical Focus Adjustment Insure yoke plugs on the A-Board are reconnected before 1. Receive a monoscope pattern. turning the Receiver ON to prevent damage to the horizontal output transistor and/or CRTs.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 7.4. Centering Magnet Adjustment 1. Receive a monoscope pattern. 2. Set that Fine convergence data (Service mode1) is clear (no correction). 3. Set that V-Pos data (Service mode1) is [130].
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 8 Deflection Adjustment Caution 8.1.3. V-Amp, V-Linear and V-Pos 1. The following adjustment have to be carried out one Adjustment with PAL signal (100i/50p) and with NTSC signal 1.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10 Convergence Adjustment The convergence adjustment is set separately for each Adjust the convergence for each of the 50/100Hz and 50/100Hz/ 60/100Hz input (NTSC, PAL/ SECAM). The 60/120Hz inputs so that they are aligned with the other colours.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10.2. Convergence Adjustment Procedure 1. Input a monoscope pattern of PAL. 2. Enter the Service Mode1. 3. Select the Coarse Convergence by pushing "RED" or "GREEN" buttons. Then push "YELLOW" button, and push Position and [N] buttons to set the data to zero.
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10.3. Coarse Convergence Adjustment mode 10.3.1. Green Coarse Convergence Adjustment 10.3.1.1. Reparation Push the "SOUND" button, and select the Green Adjustment mode.Push the "2" button, and select the "Border and Cross"...
Page 35
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10.3.1.3. "G-SIZE (H)" adjustment Push the "TV/AV" buttons, and select the "G-SIZE (H)".Push the "Volume up/down" buttons, and adjust the boarder line on either side of test pattern is aligned with the edge of the screen frame.
Page 36
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10.3.1.7. "G-CORNER" adjustment Push the "TV/AV" buttons, and select the "G-CORNER".Push the "Volume up/down" buttons, and adjust the "G-CORNER" to become the following figure. 10.3.1.8. "G-KEY" adjustment Push the "TV/AV"...
Page 37
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10.3.2. Red Coarse Convergence Adjustment 10.3.2.1. Reparation Push the "SOUND" button, and select the Red Adjustment mode.Push the "2" button, and select the "Border and Cross" pattern.Push the "MUTE" button, and select the "Yellow" colour.Push the "POSITION" button, and adjust the "R-STATIC" so that the Red color of pattern is aligned with Green colour of pattern.
Page 38
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10.3.2.6. "R-LINEAR" adjustment Push the "TV/AV" buttons, and select the "R-LINEAR".Push the "Volume up/down" buttons, and adjust the "R-LINEAR". (Refer to Fig. C.) 10.3.2.7. "R-PIN (V)" adjustment Push the "TV/AV"...
Page 39
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10.3.3.6. "B-LINEAR" adjustment Push the "TV/AV" buttons, and select the "B-LINEAR".Push the "Volume up/down" buttons, and adjust the "B-LINEAR". (Refer to Fig. C.) 10.3.3.7. "B-PIN (V)" adjustment Push the "TV/AV"...
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10.4. Fine Convergence Adjustment 8. Use the Position Buttons to adjust each point so that the 10.4.1. Green Convergence Adjustment Green Crosshatch Pattern is aligned with the vertical and 1.
Page 41
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 10.4.2. Red Convergence Adjustment 1. Push the "MUTE" button twice and change to the Red Adjustment of Yellow Colour. 2. Repeat the same steps described for the Green Conv.Adj.
Page 42
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ Fine Convergence Control Chart...
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 11 Location of Lead Wiring 11.1. Location of Lead Wiring (1) 11.2. Location of Lead Wiring (2)
Page 46
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ INSERTION OF CONNECTOR LR1, LR2, LG1, LG2, LG3, LG4, LG5, LG6, LG7, LB1, LB2, LR20, LG20, LB20 NOTICE FOR WORE DRESSING 1. Confirm that the lead line isn’t hitting the metallic part of the neck print after CRT neck print (R, G, B) insertion.
Page 47
TX-51P800X / TX-51P800HM / TX-51P800HQ / TX-43P800X / TX-43P800HM / TX-43P800HQ / TX-43P800HZ 11.4. Location of Lead Wiring (4) The Anode Lead 1. It inserts Anode lead tip in the back to FBT (the fly background transformer), and it makes turn on the right and it locks it.