Advertisement
ACC96WK_US
4/27/06
2:33 PM
Page 2
LG Electronics, Inc.
Limited Warranty - USA
This LG Electronics product, will be repaired or replaced, at LG's option, if it proves to be defective in material or work-
manship, under normal use, during the warranty period ("Warranty Period") listed below, effective from the date ("Date
of Purchase") of original consumer purchase of the product. This warranty is good only to the original purchaser of the
product and effective only when used in the United States, excluding U.S. Territories.
WARRANTY PERIOD:
HOW SERVICE IS HANDLED:
LABOR: 90 days from the Date of Purchase.
Call 1-800-243-0000 for instructions on getting the
defective unit repaired or replaced.
PARTS: One Year from the Date of Purchase.
Please retain dated sales receipt and your box to return
the unit to LG for repair or replacement.
* Parts replaced are warranted for the remaining portion of
Shipping both ways will be paid by LG during the Warranty
the original warranty period.
Period. After the Warranty Period, you pay inbound ship-
ping charges and LG pays return shipping charges.
Visit our website at: http://www.lgservice.com
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY
IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. LG ELECTRONICS WILL
NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES OF ANY NATURE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROF-
ITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT OR
OTHERWISE. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an
implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you
may also have other rights that may vary from state to state.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
•
Damages or operating problems that result from shipping, installation, adjustment of user controls, calibration,
maintenance or failure to maintain, or separate system components; and
•
Damages or operating problems that result from normal wear and tear, misuse, abuse, operation outside environ-
mental specifications or contrary to the requirements or precautions in the Operating Guide, accident, lightning
strikes or other natural causes, unauthorized modification or alteration, incorrect electrical current or voltage,
reception problem caused by inadequate home antenna or faulty antenna connections, computer software, insti-
tutional or commercial use, or other causes not arising out of defect in material or workmanship.
Therefore, the cost of repair or replacement of such defective product shall be borne by the consumer.
CUSTOMER INTER-ACTIVE CENTER NUMBERS:
For nearest Authorized Service Center, Where to buy,
Call 1-800-243-0000 (24 hours a day, 365 days per year)
Product Assistance, or Customer Assistance
and select appropriate options from the menu.
Or visit our website at http://www.lgservice.com
LG ELECTRONICS U.S.A., INC.
1000 SYLVAN AVENUE
ENGLEWOOD CLIFFS, NJ
Setup
Note:
If there is a product with a strong electromagnetic field near-
by, interference may occur.
(Ex : Micro wave oven)
Wireless TX
LED indicator
Displays the operating
status.
LED indicator of Wireless TX
* LED indicator - "BLUE"
The main set is turned on, everthing is connected and
transmitting.
* LED indicator - "RED"
The Wireless TX is in standby mode.
* LED indicator - "OFF (No display)"
The main set is turned off.
DC IN connector
ID/CHANNEL (ID./CH.)
button
SOUND SIGNAL
connector
ID./CH.
DC IN
SIGNAL
Wireless RX
LED indicator
Displays the operated
status.
LED indicator of Wireless RX
* LED indicator - "BLUE"
The Wireless TX is receiving a signal of Wireless TX.
* LED indicator - "RED"
The Wireless RX is in standby mode.
ID. button (or ID button)
Wireless speaker connector
Power cord
P/N : 3834RV0052F
Issue O
Note:
Printed in Indonesia
If there is no audio signal for longer than 5 minutes, the unit
and transmitter will automatically swith to a power saving
mode. In power saving mode, both LEDs will turn red. LEDs
will turn blue when an audio signal returns.
If you operate main unit then wireless speakers (rear speak-
ers) sound within a few seconds in standby mode.
Changing a channel of Wireless
Connection
TX and Wireless RX
Connect the speakers to the front (right, left) or center
If there is a similar wireless product nearby, interference may
speaker connectors at the main set.
occur. In this case, change to another channel using
Connect the subwoofer to the woofer connector.
ID/CHANNEL (ID./CH.) button of Wireless TX.
Connect the power cord of the Wireless RX to the outlet,
Manual setting
then connect the Wireless RX and the rear speaker (right,
left) with the speaker cable.
Press ID/CHANNEL (ID./CH.) button for about 3
Connect the DC IN connector of the Wireless TX and the
seconds.
Wireless TX (DC 7V OUT) connector at the main set with
If the wireless TX and wireless RX signals do not match after
the DC power cable.
operating as above, operate it again about three times.
Connect the SOUND SIGNAL connector of the Wireless
TX and rear (right, left) speaker of connectors of the main
Auto setting
set with the sound signal cable.
1 Disconnect the DC power cable from the Wireless TX.
Set the distance between this unit and Wireless RX within
2 Connect the DC power cable Wireless TX while you
10m.
pressing the ID/CHANNEL (ID.CH.) button of Wiress
TX.
- The blue LED indicator
will flicker
.
3 Disconnect the DC power cable from the Wireless TX
and release the ID/CHANNEL (ID.CH.) button of Wiress
TX.
4 Connect the DC power cable Wireless TX.
Note:
The wireless speakers may not receive the changed channel of trans-
mitter. In this case set the ID as below.
Setting an ID of Wireless TX and
Wireless RX
When the unit is manufactured,the ID is already set.
If an interference occurs or you use a new Wireless RX, set
a new ID.
1. Set the wireless TX and wireless RX within 50cm of
eachother.
2. Turn the Wireless TX and Wireless RX on.
3. Press the ID/CHNNEL (ID./CH.) button of Wireless TX and
ID button of Wireless RX at the same time for about 3 sec-
onds.
4. Release the ID/CHNNEL (ID./CH.) button of Wireless TX
and ID button of Wireless RX.
- ID is set up.
Notes:
If there is a product with a strong electromagnetic field nearby,
interference may occur.
Do not operate a portable transmitter (such as a wireless network
device) near this product.
About Ferrite Core
Be sure to attach the ferrite core to the speaker cables (for
connecting to this unit).
This ferrite core can reduce noises.
How to attach the ferrite core
1 Press the stopper [a] of the ferrite core to open.
2 Wind the cable once on the ferrite core.
3 Close the ferrite core unitl it clicks.
Note:
Attach the ferrite core near the unit (Refer to the fig.3 and com-
ment.).
Notes:
Optimum performance can be implemented only when the
Wireless TX and the Wireless RX within distance of 2m to 10m is
used since communication failure may occur if longer distance is
used.
Be sure to match the speaker cable to the appropriate terminal on
the components: + to + and – to –. If the cables are reversed, the
sound will be distorted and will lack base.
It takes about a few seconds (and may take longer) for the Wireless
TX and Wireless RX to communicate with each other.
When the unit is turned off, the Wireless RX is in standby mode
(off) automatically after about 10 seconds.
If the Wireless RX is turned off, the wireless speaker will not func-
tion.
Center
Front speaker
Front speaker
speaker
(Right)
(Left)
Wireless TX
SIGNAL
ID./CH.
DC IN
Red
Sound signal
Black
cable
DC power cable
Subwoofer
Wireless RX
Rear speaker
Rear speaker
(Right)
(Left)
The length here is
as short as
possible.
Advertisement
