Related Manuals for Panasonic PAN1782
Summary of Contents for Panasonic PAN1782
- Page 1 PAN1782 ® Bluetooth Low Energy Module Product Specification Rev. 1.0 Wireless Connectivity...
- Page 2 PAN1782 Bluetooth Module Overview Bluetooth • LE 2 Mbps high speed PHY, LE long range The PAN1782 is a Bluetooth 5.1 Low Energy (LE) coded PHY module based on the Nordic nRF52833 single chip • controller. LE advertising extensions (advertising on 40 channels total) •...
- Page 3 If the signed version of the Product Specification has not been returned to Panasonic within 30 days after receipt of the product, the specification or approval sheet shall be deemed to be accepted by you.
- Page 4 IN149 Informational Notice v1.1 Information on Software The PAN1782 module does not contain any software ex works, i.e. software is provided by 3rd party suppliers only. The essential software resources can be found on the partner website of Nordic Semiconductor https://www.nordicsemi.com/.
-
Page 5: Table Of Contents
PAN1782 Bluetooth Module Table of Contents About This Document ......................... 7 Purpose and Audience ......................7 Revision History ......................... 7 Use of Symbols ......................... 7 Related Documents ........................7 Overview .............................. 8 Block Diagram ........................... 9 Pin Configuration ........................10 Peripherals .......................... - Page 6 PAN1782 Bluetooth Module Appendix ............................41 Ordering Information ........................ 41 Contact Details ........................42 Product Specification Rev. 1.0 Page 6 of 42...
-
Page 7: About This Document
1.1 Purpose and Audience This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN1782 module. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as “PAN1782” and “module” within this document. -
Page 8: Overview
PAN1782 Bluetooth Module 2 Overview 2 Overview The PAN1782 is a Bluetooth 5.1 Low Energy (LE) module based on the Nordic nRF52833 single chip controller. The Bluetooth 5.1 features additionally a higher symbol rate of 2 Mbps using the high speed LE 2M PHY or a significantly longer range using the LE coded PHY at 500 kb/s or 125 kb/s. -
Page 9: Block Diagram
PAN1782 Bluetooth Module 2 Overview 2.1 Block Diagram Product Specification Rev. 1.0 Page 9 of 42... -
Page 10: Pin Configuration
PAN1782 Bluetooth Module 2 Overview 2.2 Pin Configuration Pin Assignment Top View Pin Functions Pin Name Pin Type Description Ground Connect to ground P0.30/AIN6 Digital BI/Analog Input GPIO/Analogue signal to ADC/COMP P0.18/nRESET Digital BI GPIO/Low active RESET Do not connect Power Connect 1.7 V to 3.6 V in Normal Voltage Mode... - Page 11 PAN1782 Bluetooth Module 2 Overview Pin Name Pin Type Description Do not connect Do not connect P0.28/AIN4 Digital BI GPIO or UART_RTS or Analogue signal to ADC/COM UART_RTS P0.11 Digital BI GPIO or UART_CTS UART_CTS Do not connect Do not connect...
-
Page 12: Peripherals
PAN1782 Bluetooth Module 2 Overview Pin Name Pin Type Description P0.03/AIN1 Digital BI GPIO or UART_RXD or Analogue signal to ADC/COM UART_RXD Do not connect Ground Connect to ground Ground Connect to ground Ground Connect to ground Do not connect... -
Page 13: Bluetooth Features
PAN1782 Bluetooth Module 2 Overview 2.4 Bluetooth Features • Bluetooth 5.1 LE • Supports Bluetooth 5.1 LE high speed and long-range modes • AOA and AOD direction finding Product Specification Rev. 1.0 Page 13 of 42... -
Page 14: Detailed Description
PAN1782 Bluetooth Module 3 Detailed Description 3 Detailed Description 3.1 Dimensions The dimensions are in millimeters. Top View 15.60 Item Dimension Tolerance Remark Width 8.70 ±0.30 Length 15.60 ±0.30 Height 2.00 ±0.20 With case Product Specification Rev. 1.0 Page 14 of 42... -
Page 15: Footprint
PAN1782 Bluetooth Module 3 Detailed Description 3.2 Footprint The dimensions are in millimeters. Top View 3.00 1.00 1.20 0.60 2.40 5.00 15.60 Product Specification Rev. 1.0 Page 15 of 42... -
Page 16: Packaging
PAN1782 Bluetooth Module 3 Detailed Description 3.3 Packaging The module is a mass production status product and will be delivered in the package described below. 3.3.1 Tape Dimensions 3.3.2 Packing in Tape Direction of unreeling (for customer) component Top cover tape more... - Page 17 PAN1782 Bluetooth Module 3 Detailed Description 3.3.3 Component Direction 3.3.4 Reel Dimension Product Specification Rev. 1.0 Page 17 of 42...
- Page 18 PAN1782 Bluetooth Module 3 Detailed Description 3.3.5 Package Label Example: (1T) Lot code (1P) Customer order number, if applicable (2P) Order number (9D) Date code Quantity (HW/SW) Hardware/software version 3.3.6 Total Package Product Specification Rev. 1.0 Page 18 of 42...
-
Page 19: Case Marking
PAN1782 Bluetooth Module 3 Detailed Description 3.4 Case Marking Example: Brand name Hardware/software version Order number Lot code Status: ES or empty for MP 2D barcode, for internal usage only Marking for Pin 1 Bluetooth logo Product Specification Rev. 1.0... -
Page 20: Specification
PAN1782 Bluetooth Module 4 Specification 4 Specification All specifications are over temperature and process, unless indicated otherwise. 4.1 Default Test Conditions 25 °C ± 10 °C Temperature: 40 % to 85 % RH Humidity: 3.3 V Supply Voltage: 4.2 Absolute Maximum Ratings The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. -
Page 21: Recommended Operating Conditions
PAN1782 Bluetooth Module 4 Specification 4.3 Recommended Operating Conditions The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ. Max. Unit... -
Page 22: Bluetooth
Up to 111 dB 4.6 Access Port Protection APPROTECT The PAN1782 with order number ENW89858A1KF supports the APPROTECT feature. A special sequence of commands is necessary during production programming. These commands ensure that the built-in Bluetooth Device Address is preserved when the access port protection is enabled. - Page 23 --recover, --debugreset, or --pinreset operations will work from now on. It is possible to disable the access port protection again using the option recover, but the complete PAN1782 module is erased including the built-in Bluetooth Device Address. For details how to prevent this during application development, please refer to the “PAN1782 EVB User Guide (“Bluetooth Address...
-
Page 24: Antenna Placement Recommendation
✓ Keep this module away from other high frequency circuits. ✓ Refer to the recommended pattern when designing a board. The antenna requires a cutout area of 5 mm × 3 mm under the PAN1782 module. This “Keep out Area” shall be located in every layer under the module antenna. - Page 25 PAN1782 Bluetooth Module 4 Specification Antenna Placement Recommendation All dimensions are in millimeters. Use a ground plane in the area surrounding the module wherever possible. Use stitching vias to GND left and right from the “Keep out Area” and on the...
-
Page 26: Reliability Tests
PAN1782 Bluetooth Module 4 Specification 4.8 Reliability Tests The measurement should be done after the test module has been exposed to room temperature and humidity for one hour. No. Item Limit Condition 1 Variable Vibration Test Electrical parameters should be Freq.: 20 Hz~2 000 Hz, Acc.: 17 G to... -
Page 27: Recommended Soldering Profile
PAN1782 Bluetooth Module 4 Specification 4.9 Recommended Soldering Profile • Reflow permissible cycles: 2 • Opposite side reflow is prohibited due to module weight • More than 75 percent of the soldering area shall be coated by solder •... -
Page 28: Cautions
PAN1782 Bluetooth Module 5 Cautions 5 Cautions Failure to follow the guidelines set forth in this document may result in degrading of the module functions and damage to the module. 5.1 Design Notes 1. Follow the conditions written in this specification, especially the control signals of this module. -
Page 29: Usage Condition Notes
PAN1782 Bluetooth Module 5 Cautions 5.3 Usage Condition Notes 1. Take measures to protect the module against static electricity. If pulses or transient loads (a large load, which is suddenly applied) are applied to the modules, check and evaluate their operation before assembly of the final products. -
Page 30: Other Cautions
7.2.2 Product For further information please refer to the Panasonic website Information. Product Specification Rev. 1.0 Page 30 of 42... -
Page 31: Restricted Use
Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting. -
Page 32: Regulatory And Certification Information
PAN1782 pre-certification becomes invalid. The Nordic FTPAN-254 workaround is meant for designs using an PA/LNA RF front end, which is not feasible with the PAN1782. Therefore, it is not useful to implement Nordic FTPAN-254. For further certification requests for other radio software please contact ... -
Page 33: Federal Communications Commission (Fcc) For Us
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. - Page 34 "Contains FCC ID: T7V1782". Due to the PAN1782 model size, the FCC identifier is displayed on the product package and in the installation instruction only. It cannot be displayed readable on the module’s label due to the limited size.
-
Page 35: Innovation, Science, And Economic Development (Ised) For Canada
The radiated output power of the PAN1782 with a mounted ceramic antenna (FCC ID: T7V1782) is below the FCC radio frequency exposure limits. Nevertheless, the PAN1782 shall be used in such a manner that the potential for human contact during normal operation is minimized. - Page 36 The end customer has to assure that the device has a distance of more than 15 mm from the human body under all circumstances. If the end customer application intends to use the PAN1782 in a distance smaller 15 mm from the human body, SAR evaluation has to be repeated by the OEM.
- Page 37 The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is IC: 216Q-1782 ...
-
Page 38: European Conformity According To Red (2014/53/Eu)
Panasonic inclus, ainsi que la notification ci-dessus. L’ identifiant IC est IC: 216Q-1782 7.1 Ordering Cet identifiant est valide pour tous les modules PAN1782 Information. Dans tous les cas les produits finaux doivent indiquer sur leur emballage externe la mention suivante: "Contient IC: 216Q-1782”. -
Page 39: United Kingdom Conformity According To Statutory Instrument Si 2017/1206
The end customer equipment must meet the actual Safety/Health requirements according to RED. PAN1782 and its model versions in the specified reference design can be used in all countries of the European Economic Area (Member States of the EU, European Free Trade Association States [Iceland, Liechtenstein, Norway]), Monaco, San Marino, Andorra, and Turkey. -
Page 40: Bluetooth
The end customer equipment must meet the actual Safety/Health requirements according to SI 2017/1206. PAN1782 and its model versions in the specified reference design can be used in the UK. 6.6 Bluetooth The final Bluetooth end product listing needs to be created by using the following IDs: Bluetooth 5.1... - Page 41 PAN1782 Bluetooth Module 7 Appendix 7 Appendix 7.1 Ordering Information Variants and Versions Order Number Brand Name Description ENW89858A1KF PAN1782 Bluetooth Low Energy Module with Antenna 1 500 Access Port Protection APPROTECT HW Empty Flash Abbreviation for Minimum Order Quantity (MOQ). The default MOQ for mass production is 1 500 pieces, fewer only on customer demand.
- Page 42 PAN1782 Bluetooth Module 7 Appendix 7.2 Contact Details 7.2.1 Contact Us Please contact your local Panasonic Sales office for details on additional product options and services: For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic website “Sales &...