Husqvarna 535LK Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 535LK
  6. Operator's manual

Husqvarna 535LK Operator's Manual

Hide thumbs Also See for 535LK:
Table of Contents

Advertisement

Quick Links

Download this manual
535LK
EN
Operator's manual
2-23

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 535LK

Summary of Contents for Husqvarna 535LK

  • Page 1 535LK Operator's manual 2-23...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Troubleshooting............18 Safety................3 Transportation, storage and disposal......19 Assembly................ 9 Technical data.............. 19 Operation..............11 Accessories..............20 Maintenance..............14 Declaration of Conformity..........22 Introduction Intended use Note: National regulations can set limit to the operation of the product. The product is used with a trimmer head to cut grass.

  • Page 3: Safety

    23. Combination wrench Symbols on the product Air purge bulb. WARNING! Be careful and use the product correctly. This product can cause serious injury or death to the operator or others. Read the operator's manual carefully Choke. and make sure that you understand the instructions before you use this product.
  • Page 4 Maintenance on page the adjacent area if the instructions in the qualified specialists. Refer to 14 . manual are not obeyed. • All covers, guards and handles must be fitted before you start the product. Ensure that the spark plug cap Note: Used to give more information that is necessary and ignition lead are undamaged to avoid the risk of...
  • Page 5 you have to move suddenly. Take great care when • Do not use a product with a defective muffler. you work on sloping ground. • Keep all parts of your body away from the rotating cutting attachment and hot surfaces. •...
  • Page 6 • Keep first aid equipment near. 1. Press the throttle trigger lockout (A) and make sure that the throttle control is released (B). When you release the handle the throttle control and the throttle trigger lockout both move back to their initial positions.
  • Page 7 6. Release the throttle and make sure that the cutting also prevents injuries that occur if you touch the cutting attachment stops and remains at a standstill. If the attachment. cutting attachment rotates with the throttle in the idle position the carburettor idle setting must be checked. Maintenance on See instructions under the chapter page 14 .
  • Page 8 Note: Do not remove the muffler from the product. that is in bad condition. Return product to a Husqvarna dealer/service station if the • Make sure that the muffler is correctly attached to muffler is defective.

  • Page 9: Assembly

    Safety instructions for maintenance • Never start the product if the product is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines. WARNING: Always stop the engine • Always put the product on a flat surface and make before you do any work on the sure the cutting attachment cannot come in contact cutting attachment.
  • Page 10 2. Align the tab of the cutting attachment (A) with the 4. Pull the attachment straight out of the coupling. arrow of the coupling (B). 3. Carefully push the shaft into the coupling until you hear a click. To assemble the cutting attachment guard and trimmer head 1.

  • Page 11: Operation

    (RON). There is a risk that use of lower keeps the components of the engine more clean. This octane grade causes knocking. This gives extends the life of the engine. Husqvarna alkylate fuel is rise to high engine temperature, which can not available in all markets.
  • Page 12 • If Husqvarna two-stroke oil is not available, use a 4. Tighten the fuel tank cap carefully. different two-stroke oil of good quality for air-cooled 5. Move the product 3 m (10 ft) or more away from the engines. Speak to your servicing dealer to select the refueling area and fuel source before starting.
  • Page 13 To prepare the product for start CAUTION: Do not pull the starter rope all the way out and do not let go off 1. Press the air purge again and again until the fuel the starter rope handle when the starter starts to fill the bulb.

  • Page 14: Maintenance

    To adjust the idle speed WARNING: If the cutting attachment does not stop when you Your Husqvarna product is designed and made to adjust the idle speed, turn to your specifications that decrease harmful emissions. nearest servicing dealer. Do not use the •...
  • Page 15 • The idle speed is correct when the engine operates 2. Some mufflers have a special spark arrester screen. smoothly in all positions. The idle speed must be Clean the spark arrestor screen with a wire brush below the speed when the cutting attachment starts if your product has this type of muffler.
  • Page 16 2. Fins on the flywheel. • Increased wear to engine parts. 3. Cooling fins on the cylinder. • Too much fuel consumption. 4. Cylinder cover (directs cool air over the cylinder). To clean the air filter 5. Muffler cover. 6. Muffler plate. CAUTION: A air filter that is damaged, very dirty or soaked with fuel must always be...
  • Page 17 5. If the grease level is too low fill the bevel gear with More extensive work must be carried out by an Husqvarna bevel gear grease. Fill slowly and turn authorized service workshop. the drive shaft as you apply the bevel gear grease, stop at the correct level (B).

  • Page 18: Troubleshooting

    Maintenance Daily Weekly Monthly Examine the starter and the starter rope for damages. Examine the vibration damping elements for damages and cracks. Clean the outside of the spark plug. Remove it and do a check of the electrode To examine the spark plug on gap.

  • Page 19: Transportation, Storage And Disposal

    • When the product is no longer in use, send it to • Ensure that the product is cleaned and that a a Husqvarna dealer or discard it at a recycling complete service is carried out before long-term location. storage.

  • Page 20: Accessories

    535LK Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Walbro Spark plug Champion RCJ 6Y Electrode gap, mm Fuel and lubrication system Manufacturer/type of carburettor Zama EL36D Fuel tank capacity, litre/cm 0.6/600 Weight Without fuel, cutting attachment and guard, kg...
  • Page 21 588 11 79-01 Alloy (Ø 2,0-3,3 mm cord) 588 11 79-01 588 11 79-01 Approved attachments Use with Clean sweep attachment SR600-2 535LK Hedge trimmer attachment HA110 535LK Hedge trimmer attachment HA850 535LK Hedge trimmer attachment HA200 535LK Hedge trimmer attachment HA860...

  • Page 22: Declaration Of Conformity

    Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Trimmer Brand Husqvarna Type / Model 535LK Identification Serial numbers dating from 2022 and onwards...
  • Page 23 UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Trimmer Brand Husqvarna Type / Model 535LK Identification Serial numbers dating from 2022 and onwards complies fully with the following UK regulations:...
  • Page 24 Original instructions 1143317-26 2022-11-21...

Table of Contents