Advertisement
OFD
Read me first
This Startup Guide describes the instruction until the device become ready to use.
Safety Considerations - Must Read -
Follow the instructions given in this Startup Guide for proper operations and safe use of the device.
SAFETY INDICATIONS
This Startup Guide describes the device components with possible danger, hazards that may be caused by ignoring
warnings, and preventive actions against such hazards.
Components with possible danger are indicated with a warning label placed on or around them. In the User's Guide
or warning labels, "WARNING" or "CAUTION" is used to indicate a degree of danger. These terms are defined as
follows:
Failure to heed this sign could result in serious injury or death.
Failure to heed this sign could result in personal injury or damage to properties.
Precautions and notices against hazards are presented with one of the following three symbols. The individual
symbols are defined as follows:
Attention
This symbol indicates the presence of a hazard if the instruction is
ignored. An image in the symbol illustrates the hazard type.
Prohibited
This symbol indicates prohibited actions.
Action
An image in the symbol illustrates a particular prohibited action.
Mandatory
This symbol indicates mandatory actions.
Action
An image in the symbol illustrates a mandatory action to avoid a
particular hazard.
（Sample）
A content of
A symbol for
possible danger
arousing
attention
Do not install the device while the power is turned on.
Unplug the AC power cord from the main power source when installing/uninstalling the device to/from basic processing unit or connect it with the
enclosure. Failure to follow this warning may cause an electric shock.
SYMBOLS USED IN THIS USER'S GUIDE AND WARNING LABELS
Attention
Indicates that improper use may cause an electric shock.
Indicates that improper use may cause fingers to be caught.
Indicates that improper use may cause personal injury.
Prohibited Action
Indicates a general prohibited action or warning that cannot be
specifically identified.
Mandatory Action
Unplug the power cord. Otherwise, an electric shock or fire may be
caused.
1. Verify the packed contents
Verify the packed contents with the part list given below and ensure that all the components and parts are
present. Also, check that each item is undamaged. If a component or part is missing or damaged, contact
your dealer.
2. List of compatible cartridges
Cartridge
Type
Native Capacity*
DAT320
160GByte
DAT160
80GByte
DAT160
80GByte
(WORM)
DAT72
36GByte
DDS4
20GByte
DDS3
12GByte
○：Write/Read capable
－：Cannot be use
*1：Depending on the types of data used, such as data that difficult to compress or data
that already encrypted, actual data capacity may go under the native capacity after
processed through the compression engine.
N8151-99 Built-In DAT(USB)
Follow these steps to become familiar
with your server documentation and to
complete your installation successfully.
856-857262-001- A December,2009 First edition
Please keep it carefully.
(Sample)
(Electric shock)
(Sample)
(Do not touch the part)
(Sample)
(Disconnect the power cord)
A term indicating a hazard level
Indicates that improper use may cause fumes or fire.
Indicates a general notice or warning that cannot be specifically
identified.
Do not disassemble, repair, or modify the device. Otherwise, an
electric shock or fire may be caused.
Indicates a general mandatory action or warning that cannot be
specifically identified.
Parts name
1
N8151-99 Built-In DAT(USB)
2
Cleaning cartridge
3
USB interface cable
4
CD (Device driver ,User's Guide)
5
Screws
6
Getting Started! (this manual )
Drive
N8151-99
(DAT320)
＜This device＞
1
○
○
－
－
－
－
SAFETY NOTES
General Attention
Do not use in life-critical applications or applications requiring high reliability.
This device is not intended for integration with or control of facilities or equipment
that may affect human life or that require a high degree of reliability, such as medical
equipment, nuclear power facilities, aerospace instruments, and transportation
equipment. The manufacturer does not assume any liability for accidents resulting in
injury or death, or for any damages to property that may occur as a result of using
this device in such facilities, equipment, or control systems.
Do not use the Built-in DAT if any smoke, odor, or noise is present.
If smoke, odor, or noise is present, immediately turn off the POWER switch and
disconnect the power plug from the outlet, then contact your sales agent. Using the
Built-in DAT in such conditions may cause a fire.
Keep needles or metal objects away from the Built-in DAT.
Do not insert needles or metal objects into ventilation holes in the Built-in DAT.
Failure to follow this warning may cause an electric shock.
Keep water or foreign matter away from the Built-in DAT.
Do not let any kind of liquid (water etc.) or foreign matter (e.g.,pins or paper clips)
enter the Built-in DAT. Failure to follow this warning may cause an electric shock, a
fire, or a failure of the Built-in DAT. When such things accidentally enter the Built-in
DAT, immediately turn off the power and disconnect the power plug from the outlet.
Do not disassemble the Built-in DAT. Contact your sales agent.
Attention to Installing, Moving, Storing, Connection
Do not close the ventilation hole.
Do not close the ventilation hole in the front side of the Built-in DAT. Otherwise, Its
internal temperature will rise to cause malfunctions or a fire.
Do not connect/disconnect the interface cables before unplugging the power
plug.
Before connecting/disconnecting the interface cables, disconnect the power plug of
the main power unit from the outlet. If the power is off but the power plug is still
connected, you may get an electric shock.
Do not use the unspecified interface cables.
Use only the cable authorized by NEC and locate the device and connector before
connection. Use of an unauthorized cable or displaced connection may cause a
short circuit, resulting in a fire.
When handling or connecting the interface cables, keep the notes as follows:
■ Do not tread on cables.
■ Do not load on the cable.
■ Insert the cable connector as far as it goes.
■ Do not use damaged cables.
■ Do not use damaged connectors.
Do not use the equipment in the place where corrosive gases exist.
Make sure not to locate or use the server in the place where corrosive gases (sulfur
dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, ozone, etc) exist.
Also, do not set it in the environment where the air (or dust) includes components
accelerating corrosion (ex. sulfur, sodium chloride) or conductive metals. There is a
risk of a fire due to corrosion and shorts of an internal printed board.
High temperature
Immediately after the server is powered off, its internal components
such as hard disks are very hot. Leave the server until its
internal components fully cool down before installing/removing
any component.
User's guide in attached CD describe
detailed explanation.
© NEC Corporation 2009 No copying or modifying without permission of NEC Corporation.
3. Mounting on the Basic Processing Unit
The procedure for installing the drive in a server is as follows.
(1) Install the Built-In DAT as shown here.
Qty.
1
1
1
1
4
1
(2) Connect the 10-pin connector of USB interface
cable to the USB connector on mother board.
Connect the 4-pin connector of branched cable to
the FDD connector, and the USB connector on the
N8151-78
other end to the USB connector of Built-in DAT (USB).
(DAT160)
If you do not use the floppy disk drive, put the cable for
FDD connector in a vacant place in the server.
(3) Connect the cables to the drive as shown in the figure below.
－
Use the INT USB cable provided with the device.
○
(4)After connecting the USB cable, bundle the cable so that it does not
interfere with the other devices or fan.
○
(5) Attach the cover to the basic processing unit. Plug the
power cable to the outlet.
(6) Turn on the basic processing unit.
○
○
－
4.Using the ASR function
When using the ASR (Automated System Recovery*) function in Windows, you must download and install the
device driver files from a floppy disk. Prepare a blank floppy disk, and copy the files in the "Tape Driver" folder
on the supplied CD to the blank floppy disk.
The TapeDriver folder itself shall not be included in the directory tree.
*ASR (Automated System Recovery)
Windows Server 2003, this function backs up the OS, system state, hardware composition, and applications
on your computer, allowing you to restore them in one step when recovering from a crash. For more details on
using this function, refer to the manual for your OS and backup software.
Attention to Power or Power Cord
Do not install the device while the power is turned on.
Unplug the AC power cord from the main power source when installing/uninstalling
the device to/from basic processing unit or connect it with the enclosure. Failure to
follow this warning may cause an electric shock.
Insert the DC cable into the outlet as far as it goes.
Heat generation resulting from a halfway inserted DC cable (imperfect contact) may
cause a fire. Heat will also be generated if condensation is formed on dusty blades of
the halfway inserted cable, increasing the possibility of a fire.
Do not connect the Built-in DAT by unspecified cabling.
Connecting or cabling with DC cable should be done in accordance with the
procedure specified in the User's Guide.
Unspecified connecting or cabling may cause an electric shock or a fire.
Do not use any damaged power cord.
If the power cord is damaged, immediately replace it with a new part of same type.
Do not repair the damaged section for reuse. Otherwise, the section repaired with
vinyl tape or the like will be overheated to cause an electric shock or a fire.
Use the authorized cable only.
Use only the specified cable when connecting the Built-in DAT with a basic
processing unit. Use of an unspecified cable or connection by unspecified cabling
may cause a fire.
Attention to Handling or Maintenance
Do not disassemble, repair, or alter the Built-in DAT.
Never attempt to disassemble, repair, or alter the Built-in DAT
on any occasion other than described in this User's Guide. Failure
to follow this instruction may cause an electric shock or a fire
as well as malfunctions of the Built-in DAT.
Do not handle while the power plug is connected.
Before handling or cleaning the Built-in DAT, disconnect the power plug of the main
power unit from the outlet. If the power is off but the power plug is still connected,
you may get an electric shock.
Insert the cables into the connectors as far as it goes.
Heat generation resulting from a halfway inserted cables or Interface cables
(imperfect contact) may cause a fire. Heat will also be generated if condensation is
formed on dusty blades of the halfway inserted cable, increasing the possibility of a
fire.
Attention to Operation
Do not insert your hands into the cartridge load compartment.
Do not insert your hands into the cartridge load compartment. Otherwise, the fingers
will be caught/pinched by the Built-in DAT to cause an injury.
Do not touch the Built-in DAT when it thunders.
If it starts thundering, do not touch any part of the Built-in DAT and the server that
the Built-in DAT is installed. Failure to follow this warning may cause an electric
shock.
Keep away pets.
Keep away pets from the Built-in DAT. Insertion their hair or excrements may cause
a fire or an electric shock.
Printed on recycled paper.
The contents of this document may be changed without notice.
Some servers require the rails to be used. For
details on how to install the rails, refer to the
server's operating manual.
・When using the rails with this device,
use the screw holes in the front cover
illustrated in Fig. 1 (see Fig. 2). (Perform
the same operation on the opposite side.
Secure two screws on each side, four
screws total.)
In some cases, the rails may extend all
the way to the front cover molding. This
causes no problems.
When using the rails, adjust their
mounting positions so that the front cover
of this device is aligned with the front
covers of other standard components
(such as the DVD drive).
(The shape of the rails varies according
to the model of the device.) Depending
on the device, the front cover of this
device may not align with the front covers
of other standard components.
・Please adjust to move this product forward by about
Several milliswhen mounting
on Express5800/R140a-4
・ Always use the screws that are provided with this
device. The screws that are provided with this device
are metric screws (length: 4.0 mm). Using screws that
are longer than the screws that are provided with this
device could result in damage to the device.
However, if there are screws specified to this device,
please use them. There could also be precautions
about screws from server side, so refer also to the
User's Guide of the server.
USB interface
cable
DC power cable
(unused power supply
connector in the
computer)
Advertisement
