Advertisement
The fixture controlled by the Z-Wave In-Wall Smart Switch must not exceed 960W (incandescent); 1800W (15A) Resistive or 1/2 HP Motor. The switch is designed only for use with permanently installed fixtures.
Insert wires into holes, do not wrap wires around screws.
Do not remove screws.
CONNECTING YOUR DEVICE TO A Z-WAVE NETWORK
Now you have complete control to turn your fixture ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller. If your Z-Wave certified controller features remote access, you can now control your fixture from your mobile devices.
REMOVING AND RESETTING THE DEVICE
RETURNING SWITCH TO FACTORY DEFAULTS
Quickly press ON (top) button 3 times, then, immediately press the OFF (bottom) button 3 times. The LED will flash ON/OFF 5 times when completed successfully.
Note: This should only be used in the event your network's primary controller is missing or otherwise inoperable.
CHANGING THE COLOR OF THE PADDLE
This step is optional. Before installation, you may want to change the color of the paddle to match your wallplate or décor.
This device supports Association Command Class (3 Groups)
SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture at the service panel. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the switch. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation consult a qualified electrician.
MULTI-SWITCH WIRING
The Honeywell Add-on switch is required for Multi-Switch 3-way or 4-way installations. Connecting the traveler terminal of this switch to a standard, non-Honeywell switch will cause damage or result in improper function. If this switch is a part of a 3-way or 4-way multi-switch installation, do not connect the traveler wire or apply power until Honeywell Add-on switches are correctly installed. For more information on 3-Way or 4-Way installations, view the manual or quick-start guide that comes with the Honeywell Add-on switch.
SINGLE-SWITCH WIRING
Before you start; you may wish to change the paddle color to match your wallplate or decor. Please proceed to Section 5.
GROUND — Green/Bare
LINE OR LOAD — Black (connected to power or lighting)
LINE OR LOAD — Black (connected to power or lighting)
TRAVELER — Red/Other (only in 3-way installations)
NEUTRAL — White
Match these screw terminals to the wires connected to the existing switch.
OBSERVE IMPORTANT WIRING INFORMATION
This switch is rated for and intended to only be used with copper wire.
WIRE GAUGE REQUIREMENTS
Use 14 AWG or larger wires suitable for at least 80°C for supplying Line (HOT), Load, Neutral, Ground and Traveler connections.
WIRE STRIP LENGTH
BASIC OPERATION
The connected light can be turned ON/OFF in two ways:
MANUAL CONTROL
The front panel rocker switch allows the user to turn ON/OFF the connected fixture.
CYCLE LED LIGHT
The LED below the switch acts as a guide light or status indicator.
How to cycle through options: Press up three times and down once quickly.
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. Allnon-battery operated nodes within the network willact as repeaters regardless of vendor to increase reliability of the network.
ZW4008
Power: 120VAC, 60Hz.
Signal (Frequency): 908.4/916 MHz
Maximum Loads: 960W, incandescent, 1/2HP Motor or 1800W (15A) resistive
Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module.
Operating Temperature Range: 32-104°F (0-40°C)
Type 1 enclosure, independently mounted (vertical position only), operating control: type 1.c action, pollution degree (2), impulse voltage (2500V), software class A
For indoor use only.
Specifications subject to change without notice due to continuing product improvement.
Jasco Products warrants this product to be free from manufacturing defects for two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights and you may also have other rights which vary from state to state. Please contact Customer Service at 1-855-698-8324 between 7AM – 8PM CST or via www.byjasco.com if the unit should prove defective within the warranty period.
Z-Wave ® Certified Wireless lighting Control
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Honeywell ZW4008, 39348 - Smart Switch Quick Start Guide
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the ZW4008 that isn't answered in the manual? Leave your question here.