Huawei PDU8000 Quick Installation Manual page 2

Tools / 安装工具
Phillips/Flat-head
Hammer drill
Adjustable wrench Socket wrench
screwdriver
套筒扳手
活动扳手
十字 / 一字螺丝刀
Wire stripper COAX crimping tool
Hydraulic pliers Diagonal pliers
剥线钳 液压钳 压线钳
Measuring tape Protective gloves Insulated gloves Heat gun
卷尺
防护手套 绝缘手套
Short-handle Phillips
Electroprobe Step ladder (2 m)
Electrician's knife
screwdriver (85 mm)
电笔
人字梯(2m)
电工刀
短柄十字螺丝刀(85mm)
Circuit breaker Layout / 空开示意图
NOTE / 说明
Cabinet dimensions (H x W x D): 2200 mm x 600 mm x 1200 mm
机柜尺寸（高×宽×深）：2200mm×600mm×1200mm
Input circuit breakers
输入空开
1QF 2QF
Surge protective
device (SPD) and SPD
circuit breaker FS QFS
防雷器及防雷空开
Output circuit breakers
输出空开
2
Installing a precision PDC / 安装精密配电柜
Checking Before Installation / 安装前检查
Open the packing case, and check that all components listed in the packing list are intact. Ensure that all components
are available before cleaning up the package materials. If components or fittings are damaged during transportation or
do not comply with the order contract, make records onsite and contact the local Huawei regional office or
Claw hammer representative office immediately.
冲击钻
羊角锤
打开包装箱，根据装箱清单检查设备的配件是否齐全、是否在运输过程中损坏。清除包装材料之前，要确保所有配件都
已找到。如设备和配件在运输中损坏或与订货合同不符，应及时现场记录，并与华为公司当地分公司或办事处代表联系。
Installing the Cabinet / 安装机柜
Move the cabinet from the wood pallet to the ground.
Level 将机柜从木栈板移动至地面。
斜口钳 水平尺
Plan the cabinet installation position based on the following figure.
参考下图规划机柜安装位置。
Unit: mm
单位：mm
热风枪
Drill holes using a hammer drill and install expansion bolts.
用冲击钻钻孔并安装膨胀螺栓。
Align the cabinet with mounting holes, and use a level to level the cabinet by adjusting the leveling feet.
将机柜对齐安装孔，配合水平尺调节地脚螺栓使机柜水平。
Insert bolts into the mounting holes and partially tighten the bolts.
将螺栓插入安装孔并预紧固。
NOTE / 说明
The positions and number of circuit
breakers in the figure are for reference
only. The actual product prevails.
空开位置和数量仅为示意，具体请以实
物为准。
NOTE / 说明
1. Wrench a leveling foot clockwise to elevate the cabinet, or wrench it counterclockwise to lower the cabinet. The
adjustable height ranges from 0 mm to 8 mm.
顺时针方向将机柜调高，逆时针方向调低。地脚调节范围：0mm～8mm。
2. Adjust four leveling feet to avoid damage to the cabinet. Adjusting only one leveling foot may cause the cabinet to tilt.
机柜调平过程中，不要只调节一方地脚的高度，尽量四方地脚协调调节，以免机柜倾斜造成机柜损坏。
Tighten the bolts in diagonal order.
按对角线顺序交叉紧固螺栓。
1110
1200
Bottom view of the precision PDC / 精密配电柜底部视图
NOTE / 说明
If the cabinet is installed on a support, skip
steps 2 and 3.
如果机柜安装在支架上，步骤2、3可省略。
NOTE / 说明
The following table lists the tightening
torque of different bolts.
各螺栓紧固扭矩说明如下表所示。
Bolts / Recommended Torque
螺栓 / 推荐扭矩 (N· m)
M8 13
M10 27
M12 47
M16 120
3
Installing Input and Output Cables / 安装输入输出线缆
Input cables / 输入接线
The ground terminal is identified by a
接地端子通常以
5 5 . 0 0 0 0
Cables are routed in and out from the top.
进出线方式：上进上出。
Left view of the precision PDC / 精密配电柜左视图
Output cables / 输出接线
Left view of the precision PDC / 精密配电柜左视图 Right view of the precision PDC / 精密配电柜右视图
4
NOTE / 说明
sign.
标识。
NOTE / 说明