NEC Express5800/R120f-1M Getting Started

Getting Started!
Be sure to read this guide carefully before using this
server and retain it for reference.
This document provides information required to use your server safely and properly.
Keep this document nearby so that you may refer to it as necessary. Before using this server, be sure to read
this guide and "User's Guide" (in the DVD provided with this server). For details of names in this document,
refer to Names and Functions of Parts in the "User's Guide".
Tips for your health and safety
Using a computer extensively may affect different parts of your body. Here are tips you should
follow while working on a computer to minimize strain on your body.
• Keep proper posture • Adjust the angle, brightness, and contrast of the
display to suit your preferences.
• Adjust the angle of keyboard • Take a break. Light exercise is also recommended.
The following describes the procedures from opening the carton box to
starting using this product. Be sure to follow these steps.
Instruction Manuals
To see User's Guide in EXPRESSBUILDER, follow the steps below.
(1) Turn on a computer on which Windows was installed.
(2) Insert the attached EXPRESSBUILDER DVD into the computer.
The following menu automatically appears.
(3) Click Instruction Manuals on the menu.
Express5800/R120f-1M
Step 1
Open the carton box, and then make sure you have all the accessories listed below:
Express5800/R120f-1M server × 1
●
EXPRESSBUILDER × 1
●
● Getting Started (This guide) × 1
First Edition,
September 2014
● SAS/SATA cable (when RAID controller is not installed)
Safety Precautions and Regulatory Notices × 1
●
Security key (attached to Front Bezel)
●
Important: Keep the accessories in a safe place.
Step 2
Install internal optional devices. (Go to Step 3 if you have not purchased options.)
Note: See Installing Internal Optional Devices in the "User's Guide" and the guide provided with
the optional device.
Step 3
Determine the location to place this product.
Set up a rack in an appropriate place, and then mount the server in the rack.
Note: See Proper Location and Connection in the "User's Guide".
The environment that satisfies the
following conditions
<Operating>
Ambient temperature:
10˚C to 35˚C/10˚C to 40˚C
Humidity: 20% to 80%
Temperature gradient: ±10˚C/hour
Air pressure: 749 to 1040 hpa
<Storage>
Ambient temperature:
5˚C to 40˚C
Humidity: 10% to 80%
Temperature gradient: ±15˚C/hour
Air pressure: 749 to 1040 hpa
Check the accessories.
Slide rail (outer rail) × 2
●
Slide rail (inner rail) × 2
●
● Front Bezel
Install internal optional devices.
Place the product to a proper location.
Do not use in the environment where
corrosive gas is generated.
There must be 1 m clearance in
front and behind the unit, 60 cm
on each side, and 40 cm above.
Outlet or UPS within
reach of the provided cord
Attach stabilizers.
Outlet or UPS equipped
with AC 100V/200V and
parallel bipolar ground
On the flat and robust board
Step 4
Connect cables.
Connect the cables to the server.
Note: See Proper Location and Connection in the "User's Guide".
FRONT
Display unit*
Finally, connect the
provided power cord
1
to an outlet. *
When installing
multiple racks,
be sure to
anchor them
together.
REAR
USB device
*1 Connect the power cord to a circuit breaker of up to 15 A.
*2 Either one can connect with a display unit.
USB device
2
Display unit*
2
Hub, switching hub, etc.
1000BASE-T/
100BASE-TX/
10BASE-T
Data LAN port
1 2 3 4
Management
LAN port
M
100BASE-T/
10BASE-T
Device with serial interface