Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HP UPS R/T3000
Summary of Contents for HP UPS R/T3000
- Page 1 HP UPS R/T3000 User Guide Part Number 507932-002 December 2009 (Second Edition)
- Page 2 © Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
-
Page 3: Table Of Contents
UPS front panel ............................7 UPS front panel controls ..........................8 UPS front panel LED indicators ........................8 HP UPS R/T3000 models ..........................9 R/T3000 NA and R/T3000j JPN rear panel ....................9 R/T3000h NA and R/T3000h JPN rear panel ....................10 R/T3000 INT rear panel .......................... - Page 4 Attaching the ERM front bezel ......................35 Attaching the tower conversion stands ....................35 Continuing the installation ......................... 37 UPS operations ........................... 38 Modes of operation ............................ 38 Standby mode ..........................38 Operate mode ..........................38 Configure mode ..........................39 Battery mode ...........................
- Page 5 UPS spare parts list............................. 63 ERM spare parts list ............................ 64 Hardware options ............................64 Technical support ........................65 Before you contact HP ..........................65 HP contact information ..........................65 Warranty information ........................66 Limited warranty ............................66 $250,000 Computer Load Protection Guarantee ................... 66 Pre-Failure Battery Warranty ........................
- Page 6 Grounding methods to prevent electrostatic discharge ..................74 Acronyms and abbreviations ......................75 Index ............................77...
-
Page 7: Component Identification
Component identification UPS R/T3000 overview The HP UPS R/T3000 features a 2U rack-mount with convertible tower design and offers power protection for loads up to a maximum of 3300 VA/3000 W (these numbers might vary by model). To benefit from the latest product enhancements, update to the latest versions of UPS firmware and software. -
Page 8: Ups Front Panel Controls
UPS front panel controls Item Description Function Test/Alarm Reset button Silences UPS alarms ("Silencing an audible alarm" on page 42) Off button Places the UPS in Standby mode (on page On button Powers up the UPS ("Starting power to the load"... -
Page 9: Hp Ups R/T3000 Models
On—The load level is greater than 75%. Overload On—The load level is greater than 100%. On Bypass On Battery Utility For more information, see "LED troubleshooting (on page 52)" . HP UPS R/T3000 models UPS model Description R/T3000 NA and R/T3000j • Domestic/Japanese •... -
Page 10: R/T3000H Na And R/T3000H Jpn Rear Panel
Item Description REPO port Ground bonding screw USB communications port Serial communications port Load segment 1 (two NEMA 5-20T receptacles) Load segment 2 (two NEMA 5-20T receptacles) PDU output (NEMA L - 0R) receptacle (load segment 1) ERM connector Cord retention clip attachment locations Load segment circuit breakers Power cord with L5-30 plug Option slot... -
Page 11: R/T3000 Int Rear Panel
Item Description Cord retention clip attachment locations Ground bonding screw REPO port Power cord with L6-20 plug R/T3000 INT rear panel Item Description Option slot USB port Serial communications port Load segment 1 (one IEC-320-C19 receptacle) Load segment 2 (one IEC-320-C19 receptacle) Load segment 1 (three IEC-320-C13 receptacles) Load segment 2 (three IEC-320-C13 receptacles) ERM connector... -
Page 12: Erm Rear Panel
must be connected to a remote, normally-open switch (not supplied). The REPO switch is used in conjunction with a main disconnect device that removes the AC source from the input of the UPS. When the switch is closed: • The REPO feature immediately powers down protected devices and does not utilize the orderly shutdown procedure initiated by power management software. -
Page 13: Installation
Installation Precautions Save these instructions. This document contains important safety instructions that should be followed during installation, operation, and maintenance of the UPS and batteries. WARNING: A risk of personal injury from electric shock and hazardous energy levels exists. The installation of options and routine maintenance and service of this product must be performed by individuals who are knowledgeable about the procedures, precautions, and hazards associated with AC power products. -
Page 14: Selecting A Site
Do not use the battery if the recharge date has passed. If the date on the IMPORTANT: battery recharge date label has passed without the battery being recharged, contact an HP authorized service representative for directions. Transport the packaged unit to its installation location. - Page 15 To reduce the risk of personal injury or damage to the equipment, be sure that: WARNING: • The leveling feet are extended to the floor. The full weight of the rack rests on the leveling feet. • The stabilizing feet are attached to the rack if it is a single-rack installation. •...
- Page 16 Insert screws through the rack into the mounting rail and the front of each mounting bracket. Install cage nuts or clip nuts into the rear of the rack. Installation 16...
- Page 17 Insert screws through the mounting rail into the cage nuts or clip nuts. Tighten the wing nuts or hex nuts. Installation 17...
-
Page 18: Installing The Ups In A Rack
Install the rear stabilization bracket using wing nuts. Wait until the unit is installed and the brackets are adjusted before tightening the nuts. Installing the UPS in a rack Before installing the unit, review and adhere to all warnings provided in "Precautions (on page 13)." WARNING: A risk of personal injury or damage to the equipment exists. -
Page 19: Connecting The Battery Leads
Attach the chassis to the rack using the supplied screws. Connecting the battery leads To prevent personal injury from electric shock or damage to the equipment, WARNING: remove the battery lead labels, and verify that the ERM circuit breakers are in the Off position. -
Page 20: Attaching The Ups Front Bezel
Attaching the UPS front bezel Connecting the serial communications port CAUTION: Use only the computer interface cable supplied with the UPS to connect the communications port to the host computer. IMPORTANT: Power management software requires the communications port to be appropriately cabled to the host computer.