Advertisement
Available languages
Available languages
Read me first
Be sure to read this Startup Guide carefully before using this product and retain it for reference.
This document provides information required to your product safely and properly.
Keep this document nearby so that you may use refer to it as necessary. Before using this product, be sure to read this guide
and "User's Manual" (in website : http://www.nec.com/express/).
SAFETY INDICATIONS
This Safety Precautions describes the device components with possible danger, hazards that may be caused by ignoring warnings,
and preventive actions against such hazards.
Components with possible danger are indicated with a warning label placed on or around them. In the User's Guide or warning
labels, "Warning" or "Caution" is used to indicate a degree of danger. These terms are defined as follows:
Indicates there is a risk of death or serious personal injury
Indicates there is a risk of burns, other personal injury, or property damage
Precautions and notices against hazards are presented with one of the following three symbols. The individual symbols are defined
as follows:
This symbol indicates the presence of a hazard if the instruction is ignored.
Attention
An image in the symbol illustrates the hazard type.
Prohibited
This symbol indicates prohibited actions.
Action
An image in the symbol illustrates a particular prohibited action.
This symbol indicates mandatory actions.
Mandatory
An image in the symbol illustrates a mandatory action to avoid a particular
Action
hazard.
Symbols to draw attention
Description of warning
Do not install the device while the power is on.
Unplug the AC power cord from the main power source when installing/uninstalling the device to/from basic processing
unit or connect it with the enclosure. Failure to follow this warning may cause an electric shock.
SYMBOLS USED IN THIS USER'S GUIDE AND WARNING LABELS
Attention
Indicates that improper use may cause an electric
shock.
Indicates that improper use may cause fingers to be
caught.
Indicates that improper use may cause personal injury
due to high temperature.
Prohibited Action
Indicates a non-particular and mandatory action.
Do not touch by the wet hand. Otherwise, an electric
shock may be caused.
Mandatory Action
Unplug the power cord. Otherwise, an electric shock or
fire may be caused.
N8151-139 Internal RDX Drive (USB)
GZS-000650-001-01
March 2018 Second edition
Please keep this document carefully.
(Example)
(Electric shock Risk)
(Example)
(Do not disassemble)
(Example)
(Disconnect a plug)
A term indicating a degree of danger
Indicates that improper use may cause fumes or fire.
Indicates a non-particular notice or warning.
Do not disassemble, repair, or modify the device.
Otherwise, an electric shock or fire may be caused.
Do not touch any component other than specified.
Otherwise, an electric shock or personal injury such as
bums may be caused.
Indicates a non-particular and mandatory action. Make
sure to follow the instruction.
NOTES SAFETY
General Attention
Do not use in life-critical applications or applications requiring
high reliability.
This device is not intended for integration with or control of facilities
or equipment that may affect human life or that require a high
degree of reliability, such as medical equipment, nuclear power
facilities, aerospace instruments, and transportation equipment.
The manufacturer does not assume any liability for accidents
resulting in injury or death, or for any damages to property that may
occur as a result of using this device in such facilities, equipment,
or control systems.
Do not use the Internal RDX Drive if any smoke, odor, or noise
is present.
If smoke, odor, or noise is present, immediately turn off the POWER
switch and disconnect the power plug from the outlet, then contact
your sales agent. Using the Internal RDX Drive in such conditions
may cause a fire.
Keep needles or metal objects away from the Internal RDX
Drive.
Do not insert needles or metal objects into ventilation holes in the
Internal RDX Drive. Failure to follow this warning may cause an
electric shock.
Keep water or foreign matter away from the Internal RDX Drive.
Do not let any kind of liquid (water etc.) or foreign matter (e.g., pins
or paper clips) enter the Internal RDX Drive. Failure to follow this
warning may cause an electric shock, a fire, or a failure of the
Internal RDX Drive. When such things accidentally enter the Internal
RDX Drive, immediately turn off the power and disconnect the
power plug from the outlet. Do not disassemble the Internal RDX
Drive. Contact your sales agent.
Attention to Installing, Moving, Storing, Connection
Do not close the ventilation hole.
Do not close the ventilation hole in the front side of the Internal RDX
Drive. Otherwise, Its internal temperature will rise to cause
malfunctions or a fire.
Do not connect/disconnect the interface cables before
unplugging the power plug.
Before connecting/disconnecting the interface cables, disconnect
the power plug of the main power unit from the outlet. If the power
is off but the power plug is still connected, you may get an electric
shock.
Do not use the unspecified interface cables.
Use only the cable authorized by NEC and locate the device and
connector before connection. Use of an unauthorized cable or
displaced connection may cause a short circuit, resulting in a fire.
When handling or connecting the interface cables, keep the notes
as follows:
■ Do not tread on cables.
■ Do not load on the cable.
■ Insert the cable connector as far as it goes.
■ Do not use damaged cables.
■ Do not use damaged connectors.
Do not use the equipment in the place where corrosive gases
exist.
Make sure not to locate or use the server in the place where
corrosive gases (sulfur dioxide, hydrogen sulfide, nitrogen dioxide,
chlorine, ammonia, ozone, etc) exist.
Also, do not set it in the environment where the air (or dust) includes
components accelerating corrosion (ex. sulfur, sodium chloride) or
conductive metals. There is a risk of a fire due to corrosion and
shorts of an internal printed board.
High temperature
Immediately after the server is powered off, its internal components
such as hard disks are very hot. Leave the server until its internal
components fully cool down before installing/removing any
component.
© NEC Corporation 2017 No copying or modifying without permission of NEC Corporation.
Attention to Operation
Do not insert your hands into the cartridge load compartment.
Do not insert your hands into the cartridge load compartment.
Otherwise, the fingers will be caught/pinched by the Internal RDX
Drive to cause an injury.
Do not touch the Internal RDX Drive when it thunders.
If it starts thundering, do not touch any part of the Internal RDX
Drive. Failure to follow this warning may cause an electric shock or
a fire.
Keep away pets.
Keep away pets from the Internal RDX drive. Insertion their hair or
excrements may cause a fire or an electric shock.
Attention to Power or Power Cord
Do not hold the DC cable with a wet hand.
Do not disconnect/connect the cable while your hands are wet. Failure
to follow this warning may cause an electric shock.
Do not install the device while the power is turned on.
Unplug the AC power cord from the main power source when
installing/uninstalling the device to/from server or connect it with the
enclosure. Failure to follow this warning may cause an electric
shock.
Insert the DC cable into the outlet as far as it goes.
Heat generation resulting from a halfway inserted DC cable
(imperfect contact) may cause a fire. Heat will also be generated if
condensation is formed on dusty blades of the halfway inserted
cable, increasing the possibility of a fire.
Do not connect the Internal RDX Drive (USB) by unspecified
cabling.
Connecting or cabling with DC cable should be done in accordance
with the procedure specified in the User's Guide.
Unspecified connecting or cabling may cause an electric shock or a
fire.
Do not use any damaged power cord.
If the power cord is damaged, immediately replace it with a new part
of same type. Do not repair the damaged section for reuse.
Otherwise, the section repaired with vinyl tape or the like will be
overheated to cause an electric shock or a fire.
Use the authorized cable only.
Use only the specified cable when connecting the Internal RDX
drive with a server. Use of an unspecified cable or connection by
unspecified cabling may cause a fire.
Attention to Handling or Maintenance
Do not disassemble, repair, or alter the Internal RDX Drive.
Never attempt to disassemble, repair, or alter the Internal RDX Drive
on any occasion other than described in this User's Guide. Failure
to follow this instruction may cause an electric shock or a fire as well
as malfunctions of the Internal RDX Drive.
Do not handle while the power plug is connected.
Before handling or cleaning the Internal RDX Drive, disconnect the
power plug of the main power unit from the outlet. If the power is off
but the power plug is still connected, you may get an electric shock
or may cause a fire by short-circuit.
Insert the cables into the connectors as far as it goes.
Heat generation resulting from a halfway inserted cables or
Interface cables (imperfect contact) may cause a fire. Heat will also
be generated if condensation is formed on dusty blades of the
halfway inserted cable, increasing the possibility of a fire.
Detailed handling of this device is described in the User's Guide.
Please download the User's Guide for the appropriate product from
the following URL.
http://www.nec.com/express/
Please also read the sure User's Guide before using this equipment.
Printed on recycled paper
The contents of this document may be changed without notice.
Advertisement
