Whirlpool WFW5605MW Quick Start Manual

�
�
�
�
® ® (on some models)
This symbol will be displayed when the
®
FanFresh option is activated. The fan will turn
on and the load will tumble periodically for up to
12 hours.
End
Once the cycle is complete, "End" will display. Remove the load
promptly for best results.
5. CYCLE MODIFIERS
When you select a cycle, its default settings will light up. Touch to
adjust cycle modifiers on the washer before touching Start/Pause.
Additional wash modifiers or options selected after touching
Start/Pause may not activate.
Once a wash setting is selected, it is saved for the cycle selected.
To return to factory default cycle settings, unplug washer for
30 seconds; then plug back in. See online "Cycle Guide" for
default cycle settings.
NOTE: Some modifiers may increase or decrease the estimated
time remaining.
Temp
The recommended wash temperature is preset for each cycle. Some
preset temperatures can be changed. You may select a different wash
temperature based on the level of soil and type of fabric being
washed. For best results, use the warmest wash water safe for your
fabric, following the garment label instructions. All wash temperatures
feature a cold rinse.
Spin
The recommended spin speed is preset for each cycle. Some preset
speeds can be changed.
� Faster spin speeds mean shorter dry times, but may increase
wrinkling in your load.
� Slower spin speeds reduce wrinkling, but will leave your load more
damp.
Soil
The recommended soil level is preset for each cycle. Some preset soil
levels can be changed. For heavily soiled and sturdy fabrics, select the
Heavy Soil setting. For lightly soiled and delicate fabrics, select the
Light Soil setting. Lower soil level settings will help reduce tangling and
wrinkling.
6. UTILITY CYCLES
Clean Washer with affresh ® ®
Use this every 30 washes to keep the inside of your washer fresh and
clean. This cycle uses a higher water level. Use with affresh
Cleaner tablets or liquid chlorine bleach to thoroughly clean the inside
of your washer. When using this cycle, the drum should be empty. This
cycle should not be interrupted. See "Washer Care" in the "Washer
Maintenance and Care" section of your Owner's Manual.
Drain & Spin
This cycle removes excess water from the load or special-care items
washed by hand. Use this cycle after a power failure. For some fabrics,
you may choose to set a slower spin speed.
7. CYCLE OPTIONS
You may add or remove options for each cycle. Not all options can be
used with all cycles, and some are preset to work with certain cycles.
Options vary by model.
Steam Clean (on some models)
The Steam Clean option adds additional soak and wash time to many
cycles to help remove tough stains, as well as a steam boost for added
cleaning power. An integrated heater helps to maintain optimal wash
temperatures. See online "Cycle Guide" for cycles that allow the Steam
Clean option.
You can also touch and hold Steam Clean for 3 seconds to turn cycle
signals on or off.
Extra Rinse
Activate this option to add an extra rinse to most cycles. You can also
touch and hold Extra Rinse for 3 seconds to disable/enable the Control
Lock.
Wash & Dry (on some models)
Touch to add a drying cycle to your load after the wash cycle has
finished. The Wash & Dry option is designed to wash and dry small
loads overnight. This option is designed for 2–4 lightly soiled synthetic
garments, athletic uniforms, or workout wear. This option has an extra-
high-speed spin followed by intermittent tumbling and fan activation to
circulate air through the clothes.
IMPORTANT:
� Do not use dryer sheets.
� Do not dry comforters, towels, or large blankets.
® ®
FanFresh (on some models)
Touch and hold Wash & Dry for 3 seconds to activate/deactivate the
FanFresh ® option. Use the FanFresh
remove the load promptly. The washer will automatically activate the
fan after the cycle ends and tumble the load periodically for up to
12 hours.
TumbleFresh™ ™ (on some models)
Touch to activate/deactivate the TumbleFresh™ option. Use the
TumbleFresh™ option if you will be unable to remove the load
promptly. The washer will automatically tumble the load periodically for
up to 12 hours after the cycle ends.
Load & Go™ ™ (on some models)
Touch to select this option If you want to automatically add HE
detergent to the wash load at the proper time.
®
Washer
IMPORTANT: When using the dispenser cartridge with concentrated
liquid detergent, be sure to change the detergent concentration
settings in the control if the detergent used is different than factory
preset of 2x concentration. Change the detergent concentration setting
by touching and holding Temp and Soil for 3 seconds.
You can also touch and hold Load & Go™ for 3 seconds to set a
presoak.
PreSoak (on some models)
Touch to add a presoak time of your choice to a wash cycle.
® option if you will be unable to