Electrolux EIDW1805KS Installation Instructions Manual

Built-in dishwasher
Hide thumbs Also See for EIDW1805KS:

Advertisement

Installation
Instructions
If you have questions, call 1-877-4ELECTROLUX (US) or 1-877-435-3287, 1-800-
245-8352 (Canada) or visit our website at: www.electroluxappliances.com
BEFORE YOU BEGIN
Read these Instructions completely and
carefully.
IMPORTANT
governing codes and ordinances.
• Note to Installer – Be sure to leave these instruc-
tions for the consumer's and local inspector's use.
• Note to Consumer– Keep these instructions with
your Owner's Manual for future reference.
• Skill Level– Installation of this dishwasher re-
quires basic mechanical and electrical skills.
Proper installation is the responsibility of the
installer. Product failure due to improper installa-
tion is not covered under the ELECTROLUX
Appliance Warranty.
• Completion Time – 1 to 3 Hours. New installa-
tions require more time than replacement installa-
tions.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Observe all
Built-In
Dishwasher
IMPORTANT
MUST be installed to allow for future removal from
the enclosure if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner's Manual
for available custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGs
shown throughout these instructions. While per-
forming installations described in this booklet,
gloves, safety glasses or goggles should be worn.
WARNING
To reduce the risk of electrical shock,
fire, or injury to persons, the installer
must ensure that the dishwasher is
competely enclosed at the time of
installation.
The dishwasher

Advertisement

Table of Contents
loading

Summary of Contents for Electrolux EIDW1805KS

  • Page 1: Installation Instructions

    Proper installation is the responsibility of the installer. Product failure due to improper installa- tion is not covered under the ELECTROLUX Appliance Warranty. • Completion Time – 1 to 3 Hours. New installa- tions require more time than replacement installa- tions.
  • Page 2: Parts Supplied

    PARTS SUPPLIED : Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). Two Phillips head, color matched toekick screws (in literature package). MATERIALS YOU WILL NEED: Ferrule, compression nut and 90° Elbow (3/8" NPT external thread on one end, opposite end sized to fit water supply) Thread seal tape...
  • Page 3: Prepare Dishwasher Enclosure

    Installation Preparation PREPARE DISHWASHER ENCLOSURE Plumbing and Electric Service Must Enter Shaded Area Figure A • The rough cabinet opening must be at least 24" deep and 17 5/8" to 18" wide. The opening should be 32.5" max. height. • The dishwasher must be installed so that drain DRAIN REQUIREMENTS •...
  • Page 4: Prepare Electrical Wiring

    PREPARE ELECTRICAL WIRING WARNING FOR PERSONAL SAFETY: Re- move house fuse or open circuit breaker before beginning installa- tion. Do no use an extension cord or adapter plus witthis appliance. ELECTRICAL REQUIREMENTS: • This appliance must be supplied with 120V, 60Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.
  • Page 5: Prepare Hot Water Line

    Installation Instructions PREPARE HOT WATER LINE • The line may enter from either side, rear or floor within the shaded area shown in Figure F. • The line may pass throughthe same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2"...
  • Page 6: Step 2 Adjust Leveling Legs

    Installation Instructions STEP 2 ADJUST LEVELING LEGS • Move the dishwasher close to the installation location and lay it on its back. • Measure installation height and dishwasher height. Extend leveling legs out from the dishwasher base, 1/4" less than installation height.
  • Page 7 STEP 5 POSITION WATER LIND AND HOUSE WIRING • Position water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher and components under dishwasher. STEP 6 INSERT DRAIN HOSE THROUGH CABINET •...
  • Page 8: Step 9 Level Dishwasher

    Installation Instructions STEP 8 POSTION DISHWASHER UNDER COUNTERTOP • Check to be sure that wires are secure under the dishwasher and not pinced or in contact with door springs or other dishwasher compo- nents TIP: Check tub insulation blanket, if equipped. It should be positioned so it is not bunched up or interfering with door springs.
  • Page 9: Step 10 Secure Dishwasher To Countertop Or Cabinet

    Installation Instructions STEP 10 SECURE DISHWASHER TO COUNTERTOP OR CABINET In this step you will need the 2 Phillips special head screws set aside prior to Step 1. The dishwasher must be secured to the countertop or the cabinet sides. When countertops are mad of wood, use Method 1.
  • Page 10: Step 12 Connect Drain Line

    Installation Instructions STEP 12 CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES The drain hose molded end will fit 5/8", 3/4" or 1" diameter connections on the air gap, waste tee or disposer. Cut on the marked line as required for your installation.
  • Page 11: Step 13 Connect Power Supply

    STEP 13 CONNECT POWER SUPPLY Skip this step if equipped with power cord. Verify that power is turned off at the source. • Remove junction box cover "A". • Locate the three dishwasher wires, (white, black and green) with stripped ends. Insert dishwasher wires through the small hole in the junction box "B".
  • Page 12: Step 15 Dishwasher Wet Test

    STEP 15 DISHWASHER WET TEST Turn on power supply (or plug power cord into outlet, if equipped). Turn dial to Normal "Wash" position. Close door. Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and power are turned on.

Table of Contents