Sealey AUTO SERVICE VS004.V2 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
3Follow workshop Health & Safety rules, regulations and conditions when using this equipment.
p WARNING! Disconnect from air supply before changing accessories or servicing.
3 Maintain the equipment in good condition and replace any damaged or worn parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
p WARNING! Check that correct air pressure is maintained and DOES NOT exceed 100psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
3 Wear approved safety gloves and eye and ear protection.
3 Keep gun clean and in good working order for best and safest performance.
3 Keep children and unauthorised persons away from the work area.
7 DO NOT use the gun for a task it is not designed to perform.
WARNING! DO NOT use gun if damaged or thought to be faulty. Contact your local service agent.
p
p
7 DO NOT drop, throw or abuse the gun.
7 DO NOT carry the gun by the air hose, or yank the hose from the air supply.
7 DO NOT operate the gun if you are tired or under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT direct air from the air hose at yourself or others.
3 When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATION
Eliminates the introduction of bubbles and air-locks into the cooling system and dramatically reduces system filling time. No more time-consuming
system bleeding. Reduces fluid waste and messy spills. Automatically conducts system leak test. Two adaptors cover most radiators and header
tanks, including those of commercial vehicles. Simple operation requires workshop air supply and does not require fiddly interchange of vacuum
and fluid hoses - as found on other versions of this tool. Supplied with 1.5mtr of fluid hose.
Air Pressure (max) . . . . . . . . . . . . . . 90psi (6.21 bar)
Air Pressure (min) . . . . . . . . . . . . . . . 80psi (5.55 bar)
Air Consumption (max @ 90psi) . . . 180ltr/min(10cfm)
Air Connection . . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Filling Hose Length . . . . . . . . . . . . . . . . . . . 1500mm
3. AIR SUPPLY
Recommended hook-up is shown in fig. 1.
3.1. Ensure that the trigger is in the ‘Off’ position (out) when connecting the air supply.
WARNING! Ensure that the air supply is clean and does not exceed 100psi. Too high an air pressure or unclean air will shorten the life
p
of the gun, due to excessive wear, and may be dangerous, causing damage and/or personal injury.
3.2. Drain the air tank daily.
3.3. Clean compressor air inlet filter weekly.
3.4. Line pressure should be increased to compensate for unusually long air hoses (over 8 meters). The minimum hose size should be 1/4” I.D.
and fittings must have the same internal bore.
3.5. Keep hose away from heat, oil and sharp edges. Check hose for wear and make certain that all connections are secure.
INSTRUCTIONS FOR:
FAST FILL COOLANT GUN
Model No:
give you years of trouble free performance.
VS004.V2
VS004.V2 - 1 - 210405