Advertisement
Quick Links
SERVICE MANUAL
DISHWASHERS
FOR INTERNAL AND PARTNERS USE ONLY
© ELECTROLUX HOME PRODUCTS
Consumer Service - EMEA
Quality & Continuous Improvement - Technical Support
Dishwashers with electronic control system
SERVICE MODE & ALARM CODES
• EDW 1600
• EDW 1950
• EDW 3510
For internal and partners use only.
599 79 76 - 54 Rev 2
• EDW 1850
• EDW 2200
• EDW 4010
EN
Publication number
599 79 76 – 54
Edition: 12/2017 - Rev. 2
Advertisement
Related Manuals for Electrolux EDW 1600
Summary of Contents for Electrolux EDW 1600
- Page 1 Dishwashers with electronic control system SERVICE MODE & ALARM CODES • EDW 1600 • EDW 1850 • EDW 1950 • EDW 2200 SERVICE MANUAL • EDW 3510 • EDW 4010 DISHWASHERS FOR INTERNAL AND PARTNERS USE ONLY © ELECTROLUX HOME PRODUCTS Publication number For internal and partners use only.
- Page 2 Platform with single BLDC control in separate unit (MCB) Introduction & Purpose Chapter 1 Motor Control Board (DIVA2) User Interface – Introduction Chapter 2 Auto Door Opener EDW 1600 Chapter 3.1 EDW 1850 Chapter 3.2 EDW 1950 Chapter 3.3 Electrical appliances must be serviced only EDW 2200 Chapter 3.4...
- Page 3 User interface – Introduction According to hardware configuration of the dishwasher and User Interface – Modes and Function description marketing requirement, User Mode in individual models can be a Reset subset of above functions. “Reset” is a special kind of User Operation to stop or deselect a The User Mode functions are not described in this Service Manual running program.
- Page 4 User interface – Introduction Service Mode – Function description Alarm Reading and Actuator Test After accessed Service mode to get the saved alarms and test actuators. Details of alarm code displaying are in later Alarm Code section. LED Test / Delete Alarm Memory To test the LEDS and erase alarm codes from memory.
- Page 5 EDW1600 Reset EDW 1600 Press buttons S1+S2 simultaneously for at least 2 seconds to perform Reset function. Styling Overview Access Service Mode The Service Mode can only be accessed after the Reset function Location of LEDs and Push Buttons has been carried out and the appliance is switched off.
- Page 6 EDW1600 Alarm Reading and Actuator Test Actuator Number of Number in Actuator Comment After accessed Service mode (L1, L2 and L3 blinking): S1 Pressed Display 1. Press button S1 to show the first alarm code. Regeneration Valve L1 blinks to indicate the machine is in Alarm Reading. Drain Pump Off when water level The first alarm code saved is shown in the display.
- Page 7 EDW1600 Functional Test Cycle Enable/disable Pulse Wash After accessed Service mode (L1, L2 and L3 blinking): After accessed Service mode (L1, L2 and L3 blinking): 1. Press button S3 to start the test cycle. The cycle will not start if 1.
- Page 8 EDW1850 EDW 1850 Reset Press buttons S3+S4 simultaneously for at least 2 seconds to Styling Overview perform Reset function. Access Service Mode Location of LEDs and Push Buttons The Service Mode can only be accessed after the Reset function has been carried out and the appliance is switched off. Press and hold button S1+S2 simultaneously while turn the appliance on, keep holding the buttons for 4 seconds.
- Page 9 EDW1850 L1, L2 and L3 blink to indicate that Service mode is accessed. Actuator Number of Alarm Reading and Actuator Test Number in Actuator Comment S1 Pressed Display After accessed Service mode (L1, L2 and L3 blinking): Regeneration Valve 1. Press button S1 to show the first alarm code. Drain Pump L1 blinks to indicate the machine is in Alarm Reading.
- Page 10 EDW1850 Functional Test Cycle Enable/disable Pulse Wash After accessed Service mode (L1, L2 and L3 blinking): After accessed Service mode (L1, L2 and L3 blinking): 1. Press button S3 to start the test cycle. The cycle will not start if 1.
- Page 11 EDW1950 Reset EDW 1950 Press buttons S3+S4 simultaneously for at least 2 seconds to perform Reset function. Styling Overview Location of LEDs, Access Service Mode The Service Mode can only be accessed after the Reset function Location of LEDs and Push Buttons has been carried out and the appliance is switched off.
- Page 12 EDW1950 Alarm Reading and Actuator Test Actuator Number of Number in Actuator Comment After accessed Service mode (L1, L2 and L3 blinking): S1 Pressed Display 1. Press button S1 to show the first alarm code. Regeneration Valve L1 blinks to indicate the machine is in Alarm Reading. Drain Pump Off when water level The first alarm code saved is shown in the display.
- Page 13 EDW1950 Functional Test Cycle Enable/disable Pulse Wash After accessed Service mode (L1, L2 and L3 blinking): After accessed Service mode (L1, L2 and L3 blinking): 1. Press button S3 to start the test cycle. The cycle will not start if 1.
- Page 14 EDW2200 EDW 2200 Reset Press the S3 which is dedicated to this function. Styling Overview Access Service Mode The Service Mode can only be accessed after the Reset function has been carried out and the appliance is switched off. Location of LEDs and Push Buttons EDW2200 is a touch key model.
- Page 15 EDW2200 Alarm Reading and Actuator Test Actuator Number of Number in Actuator Comment After accessed Service mode (L1, L2 and L3 blinking): S1 Pressed Display 1. Press button S2 to show the first alarm code. Regeneration Valve L1 blinks to indicate the machine is in Alarm Reading. Drain Pump Off when water level The first alarm code saved is shown in the display.
- Page 16 EDW2200 Functional Test Cycle Enable/disable Pulse Wash After accessed Service mode (L1, L2 and L3 blinking): After accessed Service mode (L1, L2 and L3 blinking): 1. Press button S5 to start the test cycle. The cycle will not start if 1.
- Page 17 EDW3510 Reset EDW 3510 Press the Program Key for at least 2 seconds, and then follow the instructions on the screen to perform Reset function. Styling Overview Access Service Mode EDW3510 is a touch key model. After Reset an off/on, press button S2+S4 simultaneously for at least 4 seconds to access Service Mode.
- Page 18 EDW4010 Reset EDW 4010 Press the Program Key for at least 2 seconds, and then follow the instructions on the screen to perform Reset function. Styling Overview Access Service Mode EDW4010 is a touch key model. After Reset an off/on, press button S5+S7 simultaneously for at least 4 seconds to access Service Mode.
- Page 19 Alarm Codes Alarm Code Description Alarm management • i00 Code family: Low mains voltage The electronic board makes sure the dishwasher operates within certain Alarm codes are defined in families of alarms and current voltage limits. If during a cycle the voltage drops below the lowest limit, the alarms, displayed as electronic board suspends all loads and interrupts the cycle under way.
- Page 20 Alarm Codes • i40 Codes - family : Analogue pressure sensor code: during dynamic filling problem • Acoustic signal and visual alarm, depending on the appliance customization; the program can be restarted. • The water level defined is not reached within the time limit set. •...
- Page 21 Alarm Codes • i46 • i55 code: Calibration invalid, pressure signal too high code: DCLink undervoltage • The warning is set if the sensor signal is out of range for an empty dw, • Alarm is set when the Vbat voltage on motorcontrolboard will be detected signal high.
- Page 22 Alarm Codes • i59 • i5B (i5H) code: WP current read ADC - fault code: WP/DP current plausibility • • Alarm is set if there is detected a fault in the current reading chain on MCB; Alarm is set if currents are not changing within 2.5 s with less than 0.0275 incl.
- Page 23 Alarm Codes Current production specific • i60 Code - family : Heating Element Problem This range includes the following PBs and PB firmware releases: This family has different meaning depending on PB and PB firmware PB100 releases. PB101 PB150 with P150R110 or later Past production specific This range includes the following PBs and PB firmware releases: A heating alarm is NOT always caused by failure of heater.
- Page 24 Alarm Codes • i64 • i6A code: heater restorable code: NTC on heater element value out of range • The alarm is stored and displayed only in service mode; the washing • The alarm is stored and displayed only in service mode; the washing program continues running program continues running •...
- Page 25 Alarm Codes • i80 Code - family : Auto Door Opener • i90 Code - family : Configuration Problem • i80 • i91 code: Auto door opener malfunction code: checksum MCF • The error is set if the auto door opener sense signal indicates that it has •...
- Page 26 Alarm Codes • iB0 (iH0) Code - family : Sensor Problem iB1 (iH1) code: turbidity sensor error • Note: “B” may be displayed as “H” in the 7-segment display • The alarm is set if lose contact with the turbidity sensor, could be because the connection to the sensor is lost.
- Page 27 Alarm Codes • iC0 Code - family : Communication Problem • iD1 code: no signal • The alarm is stored and displayed only in service mode. • iC0 code: user interface communication • If the washing pump is activated but there is no tacho signal for 5 sec then the heating element is temporarily deactivated.
- Page 28 Alarm Codes • iF1 code: high water level • The alarm is stored and displayed only in service mode. • The alarm condition is recognized if the safety water level is exceeded for more than 4 sec. • A drain phase is activated until the water level drops below the safety level. •...
- Page 29 Alarm Codes Service Code Reason Type User User failure Action in case of failure happens User Indication Family visible indication code read before March (Platform specific) 2017 Zero cross or low voltage stop Nothing User interface off & remaining time adaptation off Nothing Fill_D –...
- Page 30 Alarm Codes Service Code Reason Type User User failure Action in case of failure happens User Indication Family visible indication code read before March (Platform specific) 2017 Please OBSERVE that i6x family has different meaning depending on PBs and PB firmware versions DIVA, DIVA2, Heating problem warning...
- Page 31 Alarm Codes Service Code Reason Type User User failure Action in case of failure happens User Indication Family visible indication code read before March (Platform specific) 2017 Auto Door Opener malfunction abort Cycle will be terminated and electronic switched to reset on-condition Auto Door Opener timeout warning warning Nothing...