Advertisement
3.
SPECIFICATION
i
Model No: ......................................................CP108VMTBO
Noise Power...................................................................84dB
Noise Pressure ..............................................................73dB
No Load Speed: ....................................... 5000 - 18000 OPM
Vibration ................................................................. 0.571m/s
Uncertainty ................................................................. 1.5m/s
Battery: ............... 10.8V 2Ah - 4Ah Lithium-ion (not included)
Consumable parts
CP108VBP - 2Ah Battery, CP108VBP4 - 4Ah Battery.
Replacement parts
Mains charger ..................................................... CP108VMC
Accessories:
Sanding Paper .........................................................SMTA11
Backing Pad ............................................................. SMTA12
Scraper .................................................................................
Cutting Blade .........................................................................
4.
OPERATION
WARNING: Remove battery before fitting tool or maintenance is carried out.
‰
4.1.
To remove the battery from the equipment, depress the spring loaded button on the battery pack. Remove the battery pack by sliding
out. DO NOT touch the metal battery terminals.
4.2.
USING THE TOOL (FIG.1)
4.2.1.
Ensure that you have read, understood and comply with all the safety instructions in Section 1.
4.2.2.
Remove battery from tool. Depress tab on front face of battery and slide battery off the tool.
4.2.3.
To fit the required accessory tool bit lift the quick release handle (fig.1).
4.2.4.
Unscrew the locking collar from the drive shaft (fig.2).
4.2.5.
Locate the accessory tool onto the drive shaft spigots and refit locking collar until tight.
4.2.6.
Close quick release handle and confirm firm attachment of accessory tool.
4.2.7.
Refit battery and, ensuring that the speed controller is set to speed 1 (fig.2), slide the On/Off switch to On position.
4.2.8.
Select appropriate tool speed for the task in hand.
4.2.9.
When finished, remove the tool bit, clean the tool and tool bit and store in a cool, dry place out of the reach of children.
5. MAINTENANCE
WARNING: Always disconnect from power source before carrying out any inspection, maintenance or cleaning.
‰
5.1.
GENERAL INSPECTION
5.1.1.
Regularly check that all the fixing screws are tight.
5.1.2.
Repairs should be carried out by an authorised service centre.
5.2.
CLEANING
WARNING: Always wear protective equipment including eye protection and gloves when cleaning this tool.
‰
5.2.1.
Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the device's service life.
5.2.2.
Clean the body of your machine with a soft brush, or dry cloth.
5.2.3.
Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a damp cloth is recommended.
5.2.4.
Water must never come into contact with the tool. Ensure the tool is thoroughly dry before using it.
5.2.5.
If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable).
5.3.
LUBRICATION
5.3.1.
Lightly lubricate all moving parts at regular intervals with a suitable spray lubricant.
5.4.
BRUSHES
5.4.1.
Over time the carbon brushes inside the motor may become worn
5.4.2.
Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking.
5.4.3.
If you suspect that the brushes may be worn, have them replaced at an authorised service centre.
5.5.
STORAGE
5.5.1.
Store this tool carefully in a secure, dry place out of the reach of children.
© Jack Sealey Limited
2
2
fig.2
fig.1
Original Language Version
CP108VMTBO Issue 1
02/12/22
Advertisement
