Husqvarna 525iLK+TAB850 Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 525iLK+TAB850
  6. Operator's manual
Husqvarna 525iLK+TAB850 Operator's Manual

Husqvarna 525iLK+TAB850 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
525iLK+TAB850
EN
Operator's manual
2-23

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 525iLK+TAB850

Summary of Contents for Husqvarna 525iLK+TAB850

  • Page 1 525iLK+TAB850 Operator's manual 2-23...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Transportation, storage and disposal......18 Safety................4 Technical data.............. 19 Assembly..............11 Accessories..............20 Operation..............13 Registered trademarks..........21 Maintenance..............16 Declaration of Conformity..........22 Troubleshooting............18 Introduction Intended use Accessories on page 20 . Make sure to accessories in read this manual together with the approved accessory This power unit is a bare unit that only function...
  • Page 3 21. Bevel gear 22. Hole for locking pin 23. Trimmer head Use heavy-duty slip-resistant boots. 24. Cutting attachment guard Symbols on the product Only use non-metallic, flexible cutting attachments, i.e. trimmer WARNING! This product can heads with trimmer cord. be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others.

  • Page 4: Safety

    Manufacturer • the product has an accessory that is not from the manufacturer or not approved by the manufacturer. Husqvarna AB • the product is not repaired at an approved service Drottninggatan 2, SE-561 82 Huskvarna, Sweden, tel: center or by an approved authority.
  • Page 5 • Use personal protective equipment. Always wear • Use the power tool, accessories and tool bits etc. eye protection. Protective equipment such as dust in accordance with these instructions, taking into mask, non-skid safety shoes, hard hat or hearing account the working conditions and the work to be protection used for appropriate conditions will reduce performed.
  • Page 6 • Thoroughly inspect the area for wildlife where the is not contacting anything. A moment of inattention machine is to be used. Wildlife may be injured by the while operating the machine may result in injury to machine during operation. yourself or others.
  • Page 7 product. Do the safety checks, maintenance and • Under no circumstances may the design of the service instructions described in this manual. product be modified without the permission of the manufacturer. Always use original accessories. Non- • Faulty cutting attachment can increase the risk of authorized modifications and/or accessories can accidents.
  • Page 8 you have to move suddenly. Take great care when • Use a visor for face protection. A visor is not enough you work on sloping ground. for protection of the eyes. • Walk, never run. • Inspect the working area. Remove all loose objects, such as stones, broken glass, nails, steel wire, string etc.
  • Page 9 1. Make sure that the power trigger is locked when the CAUTION: All servicing and repair work lock is in its original position. on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below you must contact your service agent.
  • Page 10 The cutting attachment guard stops objects that ejects in • Use approved protective gloves. the direction of the operator. It also prevents injuries that • A defective or incorrect guard can cause injury. Do occur if you touch the cutting attachment. not use a cutting attachment that does not have an approved guard attached.

  • Page 11: Assembly

    Assembly To assemble the loop handle 2. Align the tab (A) with the arrow (B) on the coupling. 1. Attach the loop handle onto the shaft between the arrows. Do not place loop handle or suspension ring on label. 3. Push the shaft into the coupling until it clicks into position.
  • Page 12 To disassemble the two-piece shaft To adjust the harness 1. Turn the knob 3 turns or more to loosen the 1. Put on the harness. coupling. 2. Attach the harness to the harness support hook. 3. Adjust the length of the harness until the harness support hook is in level with your right hip.

  • Page 13: Operation

    Read and understand the safety chapter before you use the product. To connect the battery to the product WARNING: Only use Husqvarna original batteries with the product. 1. Make sure that the battery is fully charged. CAUTION: If the battery does not move easily into the battery holder, the battery is not installed correctly.
  • Page 14 • Keep the cutting attachment below waist level. time of operation for the product. The mode button has 3 speed levels. A lower level increases the time of • Keep body parts away from the hot surfaces. operation for the product. Use level 1 and level 2 if the •...
  • Page 15 3. Use 80 % speed when you cut grass near objects. 4. Use full speed when you move the product from side to side to cut grass. To cut the grass Make sure that the grass trimmer line is parallel to 1.

  • Page 16: Maintenance

    Fleet Services ™ 1. Download the Husqvarna Fleet Services app to your mobile device. ™ 2. Log on to the Husqvarna Fleet Services app. 3. Follow the instructions about how to pair the product ™ with Husqvarna Fleet Services Maintenance...
  • Page 17 Make sure that the bevel gear is filled correctly with grease, refer to the bevel gear on page 17 . If not, use Husqvarna bevel gear grease. Do a check of the connections between the battery and the product. Do a check of the connection between the battery and the battery charger.

  • Page 18: Troubleshooting

    Troubleshooting User interface LED display Possible faults Possible action Battery LED indicator flashes or- Low battery voltage. Charge the battery. ange Red error LED flashes Overload. The cutting attachment is jammed. deacti- vate the product. Remove the battery. Clean the cutting attachment from unwanted mate- rials.

  • Page 19: Technical Data

    Technical data Technical data 525iLK together with TAB850 Motor Motor type Husqvarna E-torq BLDC Speed of output shaft, 1/min 5800 Cutting width, mm Weight Weight without battery, kglb 2.9/6.4 Weight including battery (BLi200) kg/lb 4.2/9.3...

  • Page 20: Accessories

    525iLK together with TAB850 Vibration levels at handles, measured according to ISO 22867, m/s Equipped with trimmer head (original), left/right 1.4/1.5 Radio frequency data 525iLK Frequency range, GHz 2.4-2.4835 Output power , max dBm Approved batteries Battery BLi 200 Type Lithium-ion Battery capacity, Ah Nominal voltage, V...

  • Page 21: Registered Trademarks

    Bluetooth SIG, inc. and any use trademarks owned by of such marks by Husqvarna is under license. This is a specific number of an approved attachment within in an attachment group. The approved attachments are divided into attachment groups. Each attachment group has similar features and decals.

  • Page 22: Declaration Of Conformity

    Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Power Unit with Trimmer Attachment Brand Husqvarna Type / Model 525iLK+TAB850 Identification Serial numbers dating from 2023 and onwards...
  • Page 23 UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Power Unit with Trimmer Attachment Brand Husqvarna Type / Model 525iLK+TAB850 Identification Serial numbers dating from 2023 and onwards...
  • Page 24 Original instructions 1143042-26 2023-03-08...

Table of Contents