Advertisement
4. CONTENTS
Chisel Tip (1)
Anvil Tip (2)
Needle Tip (3)
Hot Knife (4)
Heat Shrink Deflector Nozzle (5)
Lead Free Solder (6)
Soldering Sponge (7)
Tip Holder/Cap (8)
Pointed Tip (9)
Stand (10)
5. OPERATION
5.1.
The tip of the appliance can be adjusted to 3 different degrees
of angle. Press the incline adjustment button (fig.1.1) and
position the appliance head according to the desired inclination.
5.2.
Press the safety lock button (fig.1.2) and at the same time lower
the ignition lever (fig.1.3) using your thumb.
This action will ignite the appliance.
NOTE: The butane flame may be barely visible in certain light conditions.
5.3.
Hold the ignition lever (fig.1.3) and release the safety lock button (fig.1.2).
5.4.
Move the continuous flame switch (fig.1.4) to the right for a constant flame.
5.5.
Adjust the flame power by moving the adjustment lever (fig.1.5) to the right to increase the power or to the left to decrease it.
5.6.
To switch off the appliance, move the continuous flame switch (fig.1.4) to the left, this will cut off the gas supply and extinguish the
flame.
5.7.
Ensure flame is extinguished and gas is off after each use.
5.8.
Stop the operation every 5 minutes to cool the tool.
6. MAINTENANCE
6.1.
REFILL
6.1.1.
Fill only with butane gas. It may be hazardous to attempt to fill with other types of gas.
6.1.2.
Refill in a well-ventilated area, away from flame, combustible materials and other persons.
6.1.3.
Please make sure the fire is off before refilling.
6.1.4.
Placing the soldering iron in an upside-down position, Insert the gas canister into the torch refilling valve.
Fill slowly. DO NOT overfill. When gas starts to Flow out, stop filling
6.1.5.
6.1.6.
After filling, wipe lighter and hands dry before igniting.
6.1.7.
After refilling operation the gas takes some minutes to stabilize.
6.1.8.
For next refilling, let the torch cool down for 5 Minutes before filling the tank.
6.2.
REPLACEMENT OR INSTALLATION OF INSERTS
WARNING! ALWAYS LEAVE TO COOL COMPLETELY THE TOOL BEFORE TO REMOVE OR REPLACE THE INSERTS.
‰
6.2.1.
Be sure to use the insert right for the job you want.
6.2.2.
Use only the inserts that fit perfectly on the tool. The inserts that DO NOT fit perfectly can result in uncontrolled and dangerous
flame. Remove the tip by turning the ring nut (fig.1.6) anticlockwise. Remove the tip and install the desired one. Tighten with the
ring nut (fig.1.6) by turning it clockwise.
6.2.3.
Tighten the inserts securely. For the completely heating of the inserts it is necessary to wait for 25 seconds.
6.3.
CLEANING
6.3.1.
Turn off the soldering iron and let it cool completely before cleaning.
6.3.2.
The outside unit can be cleaned with a damp cloth with a little mild detergent.
6.3.3.
Clean the tip on the sponge when it is still warm.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
AK2971 Issue 1 04/01/2023
fig.1
REGISTER YOUR
PURCHASE HERE
Advertisement
