DeWalt DCMCS575 Original Instructions Manual
Hide thumbs
Also See for DCMCS575:
- Original instructions manual (20 pages) ,
- Original instructions manual (208 pages) ,
- Instruction manual (35 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for DeWalt DCMCS575
Summary of Contents for DeWalt DCMCS575
- Page 1 DCMCS574 DCMCS575...
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A Fig. B Fig. C Fig. D...
- Page 4 Fig. E Fig. F 1/4" (6 mm) Fig. G Fig. H Fig. I Fig. J Fig. K...
- Page 5 Maximum Chain Speed (no‑load) 99 dB(A) (DCMCS574)/100 dB(A)DCMCS575, Maximum Cutting Length Uncertainty (K) Oil Capacity 1.8 dB(A) (DCMCS574)/2.0 dB(A)DCMCS575, Weight (without battery pack) (guaranteed sound power) 102 dB(A) Noise values and/or vibration values (triax vector sum) according to These products also comply with Directive 2014/30/EU and EN60745‑2‑13:2009+A1:2010:...
- Page 6 2.12 *Date code 201811475B or later CAUTION: Indicates a potentially hazardous situation Uncertainty (K) which, if not avoided, may result in minor or 1.8 dB(A) (DCMCS574)/2.0 dB(A)DCMCS575, moderate injury. (guaranteed sound power) NOTICE: Indicates a practice not related to 102 dB(A) personal injury which, if not avoided, may result in These products conform to the following UK Regulations property damage.
- Page 7 English parts. Damaged or entangled cords increase the risk of changing accessories, or storing power tools. Such electric shock. preventive safety measures reduce the risk of starting the power tool accidentally. e ) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord d ) Store idle power tools out of the reach of children suitable for outdoor use reduces the risk of electric shock.
- Page 8 English 6) Service k ) Cut wood only. Do not use chain saw for purposes not intended. For example: do not use chain saw for a ) Have your power tool serviced by a qualified repair cutting metal, plastic, masonry or non‑wood building person using only identical replacement parts.
- Page 9 English 2 . Do not over reach. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 3 . Keep proper footing and balance at all times. • Do not attempt operations beyond your capacity or 4 .
- Page 10 English Mains Plug Replacement • Low‑Kickback Chain ‑ A chain that complies with the kickback performance requirements of ANSI B175.1–2012 (U.K. & Ireland Only) (when tested on a representative sample of chain saws.) If a new mains plug needs to be fitted: Normal Cutting Position ‑...
- Page 11 English • Make sure that cord is located so that it will not be Charge Indicators stepped on, tripped over, or otherwise subjected to Hot/Cold Pack Delay* damage or stress. Do not use an extension cord unless it is absolutely • * The red light will continue to blink, but a yellow indicator light necessary.
- Page 12 English Battery Packs CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping Important Safety Instructions for All or falling hazard. Some tools with large battery packs Battery Packs will stand upright on the battery pack but may be easily When ordering replacement battery packs, be sure to include knocked over.
- Page 13 The Use Wh rating might The following tools operate on a 54 volt battery pack: indicate 108 Wh (1 battery implied). DCMCS574, DCMCS575, Cat #3 Storage Recommendations These battery packs may be used: DCB546, DCB547, DCB548, 1. The best storage place is one that is cool and dry away DCB549.
- Page 14 The DCMCS574 chainsaw is designed for cutting logs up to Wear head protection. 40 cm in diameter. The DCMCS575 chainsaw is designed for cutting logs up to Wear gloves. 45 cm in diameter. DO nOT use under wet conditions or in presence of flammable liquids or gases.
- Page 15 DT20688-QZ and a replacement 45 cm bar DT20687-QZ. 10. Follow the instructions in the section Adjusting • The DCMCS575 chain saw requires a replacement 50 cm chain Chain Tension. DT20690-QZ and a replacement 50 cm bar DT20689-QZ. Adjusting Chain Tension (Fig. A, E–G) Saw Chain and Guide Bar Oiling (Fig. A)
- Page 16 English nOTE: Use a high quality bar and chain oil for proper saw chain • Use a firm grip with your left hand on the front and bar lubrication. As a temporary substitute, a non-detergent handle 13 and your right hand on the rear SAE30 weight motor oil can be used.
- Page 17 English 1. To turn the unit on, push down on the the lock off lever 2 use wedges to open the cut and drop the tree along the shown in Fig. J, and squeeze the trigger switch 1 . Once the desired line of fall.
- Page 18 English MAINTENANCE 2. Place the bottom spike 23 of the chainsaw behind the area of the initial cut as shown below. Your power tool has been designed to operate over a long 3. Turn the chainsaw on then rotate the saw chain and bar period of time with a minimum of maintenance.
- Page 19 English Protecting the Environment Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste. Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries according to local provisions.
- Page 20 Belgique et WALT ‑ Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be luxembourg België en luxemburg enduser.BE@sBDinc.com Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)