Pioneer AXM-P8000 Installation Manual

AXM-P8000
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit
est conforme à CEMA.
Printed in Japan
<CRD3882-B> UC <KSNNF> <04E00000>
Installation
Note: 3. Attach the display unit to dashboard
• Before finally installing the unit, connect the
or console.
wiring temporarily, making sure it is all connect-
ed up properly, and the unit and the system work
Tapping screw
properly.
• Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.
• Consult with your nearest dealer if installation
Double faced tape
requires the drilling of holes or other modifica-
tions of the vehicle.
• Install the unit where it does not get in the dri-
Dashboard or
ver's way and cannot injure the passenger if there
console
is a sudden stop, like an emergency stop.
Installing the display unit
Drill 2 to 2.5 mm diameter holes.
Installation using the bracket
Installation using Velcro tape
1. Attach bracket (A) to the display • Thoroughly wipe off the surface before affixing
the velcro tape.
unit.
1. Affix the velcro tape (rough surface)
Display unit
to the display unit.
Display unit
Screw
Bracket (A)
Velcro tape (rough surface)
2. Attach bracket (B).
2. Attach the display unit to dashboard
or console.
Dashboard or
console
Binding screw
Bracket (B)
Washer
Velcro tape
(soft surface)
<ENGLISH>
Installation using the double faced tape Installing the hide-away unit
• Thoroughly wipe off the surface before affixing
the double faced tape.
Installation using Velcro tape
• Thoroughly wipe off the surface before affixing
Dashboard or console the velcro tape.
Hide-away unit
Double faced tape
Velcro tape
Display unit
Car mat or chassis
Connecting the Units <ENGLISH>
Note:
• This unit is for vehicles with a 12-volt battery • To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
and negative grounding. Before installing it in a
unused speaker leads without fail. There is a pos-
recreational vehicle, truck, or bus, check the bat-
sibility of short-circuiting if the leads are not
tery voltage.
insulated.
• To avoid shorts in the electrical system, be sure
to disconnect the ≠ battery cable before begin- • To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
ning installation.
is black. Connect the connectors of the same col-
• Refer to the owner's manual for details on con-
ors correctly.
necting the power amp and other units, then
make connections correctly. • If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
• Secure the wiring with cable clamps or adhesive
switch, the red lead of the unit should be con-
tape. To protect the wiring, wrap adhesive tape
nected to a terminal coupled with ignition switch
around them where they lie against metal parts.
ON/OFF operations. If this is not done, the vehi-
• Route and secure all wiring so it cannot touch
cle battery may be drained when you are away
any moving parts, such as the gear shift, hand-
from the vehicle for several hours.
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
• Don't pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protec- ACC position No ACC position
tion circuit may fail to work when it should.
• Never feed power to other equipment by cutting
• The black lead is ground. Please ground this lead
the insulation of the power supply lead of the
separately from the ground of high-current prod-
unit and tapping into the lead. The current capac-
ucts such as power amps.
ity of the lead will be exceeded, causing over-
If you ground the products together and the
heating.
ground becomes detached, there is a risk of dam-
• When replacing fuse, be sure to use only fuse of
age to the products or fire.
the rating prescribed on the fuse holder.
• Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this prod-
uct to another product, refer to the supplied
manuals of both products and connect cords that
have the same function.