Table of Contents
Advertisement
Quick Links
OWNER'S MANUAL
DISHWASHER
Before beginning installation, read these instructions
carefully. This will simplify installation and ensure that the
product is installed correctly and safely. Leave these
instructions near the product after installation for future
reference.
ENGLISH
DFB227** / DFB425** / DFB325**
MFL70282440
Rev.01_032222
Copyright © 2018-2022 LG Electronics Inc. All Rights Reserved.
www.lg.com
Advertisement
Table of Contents
Related Manuals for LG DFB227HM
Summary of Contents for LG DFB227HM
- Page 1 This will simplify installation and ensure that the product is installed correctly and safely. Leave these instructions near the product after installation for future reference. ENGLISH DFB227** / DFB425** / DFB325** www.lg.com MFL70282440 Rev.01_032222 Copyright © 2018-2022 LG Electronics Inc. All Rights Reserved.
-
Page 2: Table Of Contents
Control Panel ....................26 Wash Cycles ......................27 Options and Extra Functions ................28 Programme Table ....................31 Information for Test ..................33 Loading the Dishwasher .................34 Adding Cleaning Agents..................39 Refilling......................41 Useful Tips......................41 SMART FUNCTIONS LG ThinQ Application ..................42 Smart Diagnosis ....................44 MAINTENANCE Cleaning and Caring ..................45... - Page 3 TROUBLESHOOTING Before Calling for Service................49...
-
Page 4: Safety Instructions
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE The following safety guidelines are intended to prevent unforeseen risks or damage from unsafe or incorrect operation of the appliance. The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as described below. Safety Messages This symbol is displayed to indicate matters and operations that can cause risk. - Page 5 • Do not modify the power cord provided with the appliance. Please contact the LG Customer information centre to advise of its incompatibility. • This appliance should only be transported by two or more people holding the appliance securely.
- Page 6 • Connect the ground wire to the green ground connector in the terminal box. Operation • Immediately unplug the power plug and contact an LG Electronics customer information centre if you detect a strange sound, odour, or smoke coming from the appliance.
- Page 7 • In case of flood, disconnect the power plug and contact the LG Electronics Customer Information Centre. • Under certain conditions, hydrogen gas may be produced in a hot- water system that has not been used for two weeks or more.
- Page 8 SAFETY INSTRUCTIONS • Do not operate the appliance unless all enclosure panels are properly in place. • Use only detergents or wetting agents recommended for use in a appliance and keep them out of the reach of children. • Do not wash and dry articles that have been soaked in explosive substances such as gasoline, solvents, solvent-based detergent.
-
Page 9: Caution Statements
SAFETY INSTRUCTIONS • The door should not be left in the open position since this could present a tripping hazard. Maintenance • Never unplug the appliance by pulling on the power cable. Always grip the power plug firmly and pull straight out from the socket outlet. - Page 10 SAFETY INSTRUCTIONS Operation • Turn off the water tap and unplug the appliance if the appliance is to be left for an extended period of time, such as during vacations. • Do not place objects on the top of the appliance. •...
-
Page 11: Installation Parts And Specifications
INSTALLATION INSTALLATION Parts and Specifications NOTE • Appearance and specifications may change without notice to improve the quality of the appliance. Front View Interior View Top Wash Impeller Control Panel & Door Handle Upper Spray Arm Front Cover Lower Spray Arm Lower Cover Salt Container Cap Levelling Feet... - Page 12 INSTALLATION Accessories Funnel Noise Strap Cover Felt Moisture Barrier Tape (Aluminum tape) *1 Noise strips are provided: Lower - 1 EA, Front - 1 EA, Side - 2 EA *2 This feature is only available on some models. Specifications Model DFB425** DFB227** / DFB325** Power Supply...
-
Page 13: Preparing Cabinet Opening
INSTALLATION Preparing Cabinet Opening • Install the appliance on a flat and stable area. Do not place any objects in-between the floor and base or leg off the appliance. Choosing the Proper Location NOTE • This installation must be conducted by qualified service personnel to ensure it has been installed correctly. - Page 14 INSTALLATION Lay down the appliance and pull on both the Remove the double-sided tape from the lower hooks at the bottom of the lower cover. and front strips. Attach the black coloured lower strip to the bottom of the lower cover. Pull on the lower cover to remove it.
- Page 15 INSTALLATION Attaching the Strip to the Remove the 2 screws on the back. Appliance Side Cabinet To reduce noise attach the strip to the appliance sides, if the opening space allows. Remove the double-side tape from the side strips. Pull the top cover backwards after removing Attach the side strip to the front of the side the two screws and then lift it up to remove it.
-
Page 16: Levelling The Appliance
INSTALLATION Levelling the Appliance Clean and dry the underside of the counter top on which the tape will be attached. Checking the Level Levelling the appliance prevents unnecessary leakage and poor washing. Check whether the appliance is perfectly level after installation. •... -
Page 17: Installing The Drain Hose
INSTALLATION Check the opening of door and repeat if • This should be available from a plumbing shop necessary until the door opens and closes or a hardware store. properly. Connection to the Waste Spigot Check the waste spigot when initially installing. An error can occur when the waste spigot below the sink is not drilled out properly. -
Page 18: Preparing Water And Electrical Connections
INSTALLATION Preparing Water and Method 1 Electrical Connections When the drain hose is connected to a waste spigot, the hose must be looped up to the underside of the bench top and secured. Connecting the Hose to the Water Tap Connect the water supply hose to the water tap. -
Page 19: Final Installation Check
INSTALLATION Final Installation Check • Use sealant tape or sealing compound on the tap’s thread to avoid water leaks. Testing the Dishwasher • Make sure that the line is not kinked or sharply bent. Turn on electrical power. NOTE Turn on house water supply. •... - Page 20 INSTALLATION Error Possible Cause and Solution Code Water supply line kinked under dishwasher. • Feed the drainage and supply hoses through the hole under the sink. Then gradually slide the dishwasher into the cabinet while pulling on the hoses under the sink to take up any slack.
-
Page 21: Operation Operation Overview
OPERATION OPERATION Operation Overview • Make certain that no dishes or utensils are in the path of the spray arms. Using the Appliance • Do not place one dish on top of another. Press the Power button. • The unit will turn on. Check the indicators. Check that there is rinse aid and dishwasher salt present. -
Page 22: Before Using
OPERATION Method 2 NOTE You can check water hardness by using the test • It is not recommended to rinse the dishes strip included in the product. manually before operating the dishwasher Immerse all reaction zones of the test strip for because it increases water and energy about a second. - Page 23 OPERATION Water Hardness Table Water Hardness Softeni Ratio mmol/l mg/l ng level °d °e °f Range (Ca+Mg) (Ca) <4 <5 <7 <0.7 <29 Soft 4 - 7 5 - 9 7 - 13 0.7 - 1.3 29 - 50 1:24 7 - 14 9 - 17.5 13 - 25...
- Page 24 OPERATION Remove the lower rack and remove the cap of rust or damage to the appliance if the left the salt dispenser located on the left side of the unwashed. filters. Before using the appliance for the first time, it is necessary to pour 1 kg of dishwasher salt and 1 litre of water at the same time if intending to use the water softener system.
- Page 25 OPERATION Close the lid to lock the dispenser. Rinse aid is NOTE dispensed automatically during the final rinse cycle. • The Rinse Aid Refill icon will illuminate when more rinse aid is needed. CAUTION • If you notice cloudy spots, streaks or water •...
-
Page 26: Control Panel
OPERATION Control Panel Control Panel Features For Steam Models Power • Press Power button to turn power on and off. • After the cycle is complete, the power automatically turns off for purposes of safety and economy. • If there is a power surge, power outage, or disruption of any kind, power is automatically turned off for safety. -
Page 27: Wash Cycles
OPERATION Chime On/Off • To activate or deactivate the button sounds, press and hold Dual Zone and Energy Saver simultaneously for 3 seconds. The error alert sound cannot be turned off. Cancel • The drain pump activates and the cycle cancels. Once the appliance finishes draining, the power turns off. -
Page 28: Options And Extra Functions
OPERATION Machine Clean Dual Zone This cycle is for cleaning the inside of the appliance. This option automatically sets the spray intensity to Use the cycle without dishes in the appliance. It soft for the upper spray arm and strong for the eliminates residual soils, odor, white spots, lower spray arm. - Page 29 OPERATION • When the rinse aid is empty, this option is The Auto Open Dry feature enhances the drying selected automatically. performance by opening the door automatically during the drying stage within the displayed program time. For optimum drying results wait until the program ends before unloading the Delay Start dishwasher.
- Page 30 OPERATION • Depending on the model, the lamp may be located either on the front of the appliance or the top of the door. Red (left) The red lamp flashes when the appliance encounters an error. For more information about the error, see the Error Code part of the TROUBLESHOOTING section.
-
Page 31: Programme Table
OPERATION Programme Table Programme Guide For Steam Models Wash Rinse Program Soil Level Pre-wash Main wash Rinse Heating rinse Auto All levels (50 - 55 ℃) (70 ℃) Intensive Heavy (75 ℃) (70 ℃) Delicate Light (55 ℃) (70 ℃) Refresh (75 ℃) Moderate... - Page 32 OPERATION Available Options NOTE • The Energy Saver option is not available with the High Temp or Extra Dry option. • The Delay Start option can be selected for every washing programme in this table. For Steam Models Programm Energy Dual Zone Half Load Steam...
-
Page 33: Information For Test
OPERATION Information for Test Cutlery Rack Information for Water Efficiency Test (EN50242) Appliance loaded in accordance with standard specifications. For water efficiency labelling program, please select Eco as the recommended program for normally soiled tableware at rated dishwasher capacity. For Models with Auto Open Dry Function •... -
Page 34: Loading The Dishwasher
OPERATION Lower Rack • Make sure that all items do not touch each other. Items not Suitable for Dishwashers The combination of high water temperature and dishwasher detergents may damage certain items. Do not wash the following items. • Copper or anodised aluminium •... - Page 35 OPERATION Loading the Upper Rack To make it easier to load larger dishes, the front row of tines can be folded down. Daily Use Load The upper rack is suitable for delicate items such as, small plates, long cutlery, cups, glasses and appliance safe plastic items.
- Page 36 OPERATION • The rack on the left pops free at the back. CAUTION The rack on the right pops free at the front. • The spray arms must not be blocked by items that are too tall or hang through the baskets. Test for free movement by manually rotating the spray arms.
- Page 37 OPERATION Raising the Rack There are three available positions for adjusting the height of the upper rack to create more space. Lift the rack at the centre of each side until the rack locks into place in the upper position. It is not necessary to lift the lock levers to raise the rack.
- Page 38 OPERATION Place forks and spoons in the cutlery basket with NOTE their handles downwards. • To set the rack to the middle position, it may be easier to lower the rack all the way down and then raise each side of the rack individually until it clicks into place.
-
Page 39: Adding Cleaning Agents
OPERATION rack help keep utensils separated to avoid damage of different sizes. Remove dishes before adjusting and improve cleaning. the tray. Adjust the tray by sliding the lever. Removing the Cutlery Rack The entire cutlery rack can be removed if more space is needed on the upper rack for larger items. - Page 40 OPERATION • The amount of detergent needed depends on the cycle, load size, and soil level of dishes. Amount of detergent • Put detergent into the detergent compartment Programme Pre-wash Main wash before starting any cycle, except the Rinse cycle. (onto the lid) (dispenser) Push the button on the dispenser lid to open...
-
Page 41: Refilling
OPERATION • Use of an unsuitable detergent and rinse aid any spilled salt inside the appliance may cause rust may result in a risk of damage, corrosion, poor or damage to the appliance if the left unwashed. washing results, poor drying or leakage. When the salt refill icon illuminates, it means the •... -
Page 42: Smart Functions
Allows you to set various options on the appliance and in the application. Push Alert When the cycle is complete or the appliance has problems, you have the option of receiving push notifications on a smartphone. The notifications are triggered even if the LG ThinQ application is off. - Page 43 Internet service provider or refer to your On your smartphone, disconnect to your home Wi- wireless router manual. Fi network. • LG ThinQ is not responsible for any network connection problems or any faults, Run the LG ThinQ application. malfunctions, or errors caused by network connection.
-
Page 44: Smart Diagnosis
SMART FUNCTIONS LG Electronics will also provide open source code to the instructions for audible diagnosis provided you on CD-ROM for a charge covering the cost of in the LG ThinQ application. performing such distribution (such as the cost of... -
Page 45: Maintenance
MAINTENANCE MAINTENANCE To maintain performance and prevent problems, Food residue may be stuck in the narrow gaps check the outside and inside of the appliance, inside the appliance after completion of washing. including filters and spray arms regularly. Wipe off all food residue. WARNING •... - Page 46 MAINTENANCE white vinegar into shallow bowl and place in upper Clean the filters with a soft brush under rack. Run Auto cycle. Do not use detergent. When running water. Reassemble the filters before the cycle is finished, restart. reinstalling them. CAUTION •...
- Page 47 MAINTENANCE When cleaning is necessary, remove the upper NOTE spray arm by turning the nut on the bottom of the spray arm 1/8 turn counterclockwise and • When assembling, rotate it firmly until it clicks. pulling down. Cleaning the Spray Arms If the spray arm holes are blocked by any food residue, dishes may not be cleaned well due to Remove food particles by rinsing or shaking...
- Page 48 MAINTENANCE After assembly, check whether the spray arms • When reassembling the seal and the filter, rotate freely. ensure that they free from dirt or grit that may have come from the water supply. Cleaning the Water Supply Hose Filter Seasonal Maintenance and Storage Unplug the appliance.
- Page 49 The appliance is equipped with an automatic error-monitoring system to detect and diagnose problems at an early stage. If this appliance does not function properly or does not function at all, check the following before you call LG Electronics service centre. Symptoms Possible Cause &...
- Page 50 TROUBLESHOOTING Symptoms Possible Cause & Solution Motor trouble • Call for service if the same problem occurs again. Vario motor trouble • Call for service if the same problem occurs again. Operation Symptoms Possible Cause & Solution Noise Some level of noise is normal during operation. •...
- Page 51 TROUBLESHOOTING Symptoms Possible Cause & Solution Water remains in sump Drain hose is kinked or clogged. after completion of • Adjust hose or clear blockage. cycle. Water may remain if the power supply was lost before normal end of the course or was manually disconnected.
- Page 52 TROUBLESHOOTING Symptoms Possible Cause & Solution Black or gray marks on Aluminum items rubbing dishes during cycle dishes • Reposition the dishes. Yellow or brown film Coffee or tea stains on inside surfaces of • Eliminate the stain by using a stain removal product. appliance Yellow water remains When initially using the appliance, Yellow water may generate in the...
- Page 53 TROUBLESHOOTING Symptoms Possible Cause & Solution Odour The previous cycle was stopped before completion and residual water remains in the appliance. • Turn on the power, run the Cancel cycle option to remove the residual water, then run the Turbo cycle using detergent but with the appliance empty.
- Page 54 • Find the Wi-Fi network connected to your smartphone and remove it, then not connected to the register your appliance on LG ThinQ. Wi-Fi network. Mobile data for your smartphone is turned on. • Turn off the Mobile data of your smartphone and register the appliance using the Wi-Fi network.
- Page 55 Memo...