Page 1
DC-DA280 INSTRUCTION MANUAL Micro Component System LINE FM MODE REPEAT PRESET MEMORY VOLUME TUNER SOUND TUNING /BAND PRESET REMOTE CONTROLLER RB-DA280 ENGLISH ESPAÑOL...
Page 2
CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE FOR STRÅLING. VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRR ÄR URKOPPLAD.
Page 3
To an AC outlet Fig. 1 Screws (not supplied) Fig. 3b Fig. 3a Remote sensor Within approx. 7 meters Two R03 batteries (not supplied) LINE FM MODE REPEAT PRESET MEMORY VOLUME TUNER SOUND /BAND TUNING PRESET REMOTE CONTROLLER RB-DA280 Fig. 4 Fig. 2...
Page 4
Fig. 5a Fig. 5b LINE FM MODE REPEAT PRESET MEMORY VOLUME TUNER SOUND TUNING /BAND PRESET REMOTE CONTROLLER RB-DA280 Fig. 5c Fig. 5d Fig. 6 Cotton swab Capstan Pinch roller 4, 5. Head Fig. 7 Fig. 8 Fig. 9 Side A Side B Break out tab A for side A.
ENGLISH PRECAUTIONS CONTROLS (Fig. 5) The apparatus shall not be exposed to dripping or splashing. General (Fig. 5a) Do not use where there are extremes of temperature (below 5°C or 1. Power button (Y OFF, Z ON) exceeding 35°C) or where direct sunlight may strike it. 2.
Inserting batteries (Fig. 2) 5. Press the CD button. Play starts from the first track. Note: Always remove batteries if the remote control is not to be used for a month or more. Batteries left in the unit may leak and cause damage. Remote control range (Fig.
2. Select a track by using the E or F button. To preset stations (Remote control only) The number buttons on the remote control can also be used. Up to 24 stations for FM band, 12 stations for AM band, can be preset. 1.
Recording copyright material without permission of the copyright owners is usually an infringement. If you wish to re-record copyright material, permission from the copyright owner is necessary. SANYO does not approve of, and cannot be held responsible for, any unlawful use of this machine.
80 Hz to 135 kHz 145(W) x 230(H) x 170(D) mm Signal-to-noise ratio: Weight: 40 dB 1.2 kg (per speaker) Wow/flutter: 0.15% (WRMS) Specifications subject to change without notice. Fast forward/rewind time: Approx. 110 sec. (C-60) (SP) 1AD6P1P1584-A SANYO Electric Co., Ltd.
Clean a lens with swab of the cotton which moistened it with alcohol, cleaning paper or cleaning disc appointed. Specified cleaning disc : LC-1 (Part code : 645 026 1961 ..manufactured by SANYO.) Show a clean procedure in the following in reference by swab of cotton.
CD PLAYER ADJUSTMENTS (2) Checking the "eye" pattern 1. Switch "ON" the POWER. (RF) 2. Connect an oscilloscope to TP1 (RF) and TP4 (VC). OSCILLOSCOPE 3. Load the test disc. 4. Press the PLAY button. (VC) 5. Check to be sure that the "eye" pattern is at the center of waveform and that the diamond shape is clearly defined.
Page 13
TUNER ADJUSTMENTS (for UK) • Use a plastic screw driver for adjustments. • MODE : ST (Stereo) • Speaker impedance : 4 ohm • TUNING TP13 T2002 L2154 L2153 TP11 FM : 87.5 - 108MHz TP15 TP14 XF233 TP24 MW: 522 - 1611kHz 520 - 1610kHz XF221 L2104...
Page 14
TUNER ADJUSTMENTS (for SP) • Use a plastic screw driver for adjustments. • MODE : ST (Stereo) • Speaker impedance : 4 ohm • TUNING FM : 87.5 - 108MHz AM : 522 - 1611kHz TP13 520 - 1610kHz T2002 TP11 L2153 XF233...
Page 21
IC BLOCK DIAGRAM & DESCRIPTION IC101 LA9241ML (Servo Signal Processor) No. Pin Name I/O Function No. Pin Name I/O Function FIN2 I Connection Pin for Photo Diode of Pickup. I Input Pin for Tracking Jump Signal from Digital FIN1 I FIN2 + FIN1 = RF, FIN2 - FIN1 = FE I Signal Processor.
Page 22
IC BLOCK DIAGRAM & DESCRIPTION IC102 LC78622NE (Digital Signal Processor) No. Pin Name I/O Function No. Pin Name I/O Function DEFI I Input terminal for detect signal of defect TEST3 I Test pin. I Input terminal for test. TEST4 I Test pin. O The phase comparison output terminal for - Non connection.