Sealey Siegen S0100 Instructions

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear ear
instruction protection
manual
1. sAFetY
wArninG! ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
‰
wArninG! disconnect from air supply before changing accessories or servicing.
‰
maintain the wrench in good condition and replace any damaged or worn parts. use genuine parts only. unauthorised parts may be
9
dangerous and will invalidate the warranty.
wArninG! check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are secure.
9
Only use impact sockets which are specifically designed for use with an impact wrench.
9
Wear approved safety eye/face shield, ear defenders and hand protection.
9
wArninG! due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we
‰
recommend you wear suitable respiratory protection.
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non-essential persons away from the working area.
9
dO nOt use the wrench for a task it is not designed to perform.
8
wArninG! dO nOt use wrench if damaged or thought to be faulty (contact service Agent).
‰
dO nOt use wrench unless you have been instructed in its use by a qualified person.
8
dO nOt carry the wrench by the air hose, or yank the hose from the air supply.
8
dO nOt operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
dO nOt carry wrench with your hand on the trigger in order to avoid unintentional starting.
8
dO nOt direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. intrOductiOn
fitted with rocking dog hammer and hardened impact anvil. features four-position adjustable air/torque control and reversible action. suitable for
diY enthusiast and light garage use.
3. speciFicAtiOn
model no: ...................................................................... s0100
drive: .................................................................................. 1/2"
Working torque: ..............................................220lb.ft (299nm)
maximum torque: ............................................260lb.ft (354nm)
ultimate torque: ..............................................390lb.ft (530nm)
free speed: ................................................................ 7000rpm
Air consumption: ................................................................5cfm
operating pressure: .......................................................... 90psi
Air inlet size: ................................................................ 1/4"BsP
Weight: .............................................................................2.2kg
noise power/pressure: ......................................... 106/95dB(A)
Vibration/uncertainty: .............................................9.21/1.5m/s²
4. prepArAtiOn
4.1. Air supply
4.1.1. recommended hook-up procedure is shown in fig.1.
4.1.2. ensure wrench air valve (or trigger) is in the "off" position (i.e. released) before connecting to the air supply.
4.1.3. You will require an air pressure of 90psi, and an air flow according to specification.
wArninG! ensure the air supply is clean and does not exceed 90 psi while operating the wrench. too high an air pressure and
‰
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.4. drain the compressor air tank daily. Water in the air line will damage the wrench.
4.1.5. clean air inlet filter weekly. line pressure should be increased to compensate for unusually long air hoses (over 8 metres). the minimum
hose diameter should be 1/4" i.d. and fittings must have the same inside dimensions.
4.1.6. Keep hose away from heat, oil and sharp edges. check hose for wear, and make certain that all connections are secure.
© Jack sealey limited
instructions for
Air impAct wrench 1/2" sq. drive
model no:
Wear eye Wear a mask
protection
Original Language Version
s0100
s0100 | issue 2 17/03/17