Sealey SA56 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
‰
WARNING! Disconnect from air supply before changing accessories or servicing.
‰
Maintain the tool in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Wear approved safety eye/face shield, ear defenders and hand protection.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non essential persons away from the working area.
9
DO NOT use the tool for a task it is not designed to perform.
8
WARNING! DO NOT use tool if damaged or thought to be faulty. Contact a Sealey service agent.
‰
DO NOT use tool unless you have been instructed in its use by a qualified person.
8
DO NOT carry the tool by the air hose, or yank the hose from the air supply.
8
DO NOT operate tool if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry tool with your hand on the power trigger in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. INTRODUCTION
Pistol grip design for increased control and manoeuvrability. Finger tipped control and polished aluminium housing with alloy head. Suitable for
cutting straight lines in steel metal sheet up to 1.2mm thickness.
3. SPECIFICATION
Model no ....................................................................... SA56
Air consumption ............................................................. 4cfm
Consumable parts
Replacement blade outer right ................................. SA56.31
Replacement blade outer left ................................... SA56.32
Replacement blade centre ....................................... SA56.33
Inlet size ....................................................................1/4"BSP
Max. cutting capacity ....................................... 1.2mm (steel)
Noise power/pressure .......................................... 99/88dB(A)
Operating pressure ....................................................... 90psi
Vibration/uncertainty ............................................. 4/0.13m/s²
4. PREPARATION
4.1. AIR SUPPLY
4.1.1. Recommended hook-up procedure is shown in fig.1.
4.1.2. Ensure tool valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.3. You will require an air pressure of 90psi, and an air flow according to specification.
WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the tool. Too high an air pressure and/or
‰
unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.4. Drain the air tank daily. Water in the air line will damage the tool.
4.1.5. Clean air inlet filter weekly.
4.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 meters). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
4.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
4.2. COUPLINGS
4.2.1. Vibration may cause failure if a quick change coupling is connected directly to the tool. To overcome this, connect a leader hose to the
tool. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See figs.1 & 2.
© Jack Sealey Limited
All manuals and user guides at all-guides.com
PISTOL TYPE AIR SHEARS
MODEL NO:
Wear ear Wear hand
protection protection
Original Language Version
SA56
fig.1
fig.2